Raven RS1 Installation Manual

Case IH Patriot 4440 Model Year 2017-2018 Raven RS1™ HDU Guidance and Steering Installation Manual 016-5032-109 Rev. D 4/2020 E35334 ...

We Solve Great Challenges. DISCLAIMER While every effort has been made to ensure the accuracy of this document, Raven Industries assumes no responsibility for omissions and errors. Nor is any liability assumed for damages resulting from the use of information contained herein. Raven Industries shall not be responsible or liable for incidental or consequential damages or a loss of anticipated benefits or profits, work stoppag ...

016-5032-109 Rev. D i Chapter 1 Important Information.......................................................................................... 1 Safety ...............................................................................................................................................................................1 Displays and Control Consoles .................................................................................. ...

ii Case IH Patriot 4440 Model Year 2017-2018 Raven RS1™ HDU Guidance and Steering Installation Manual ...

1 CHAPTER 1IMPORTANT INFORMATION SAFETY Follow the operation and safety instructions included with the implement and/or controller and read this manual carefully before installing or operating this Raven system. • Follow all safety information presented within this manual. Review implement operation with your local dealer. • Contact a local Raven dealer for assistance with any portion of the installation, service ...

HYDRAULIC SAFETY When installing or servicing a hydraulic system or hydraulic components, be aware that hydraulic fluid may be extremely hot and under high pressure. Caution must be exercised. • Always wear appropriate personal protective equipment when installing or servicing hydraulic systems. • Never attempt to open or work on a hydraulic ...

3 IMPORTANT INFORMATION RECOMMENDATIONS AND BEST PRACTICES HOSE ROUTING The word “hose” is used to describe any flexible, fluid carrying components. Use the following guidelines and recommendations when connecting and routing hoses while installing or maintaining this Raven system: • Leave protective caps/covers over hose ends until connecting the end into the hydraulic system to help prevent ...

• Protect harnessing from sharp bends, twisting, or flexing over short distances and normal implement operation. • Connectors and splices should not be located at bending points or in harness sections that move. • Ensure sufficient length for free movement of the implement during normal operation and prevent pulling, pinching, catching, or ...

5 CHAPTER 2INTRODUCTION Congratulations on your purchase of the RS1 HDU system! The following instructions are designed to assist with the proper installation of the RS1 HDU system. Refer to the RS1 Calibration & Operation Manual (P/N 016-4010-001) for assistance with calibrating the software and using the RS1 HDU system. PREPARING FOR INSTALLATION Before installing the RS1 HDU system, park the machine where the ground is leve ...

UPDATES Updates for Raven manuals as well as software updates for Raven consoles, and product controllers are available at the Applied Technology Division web site: https://portal.ravenprecision.com Sign up for e-mail alerts to receive notifications when updates for your Raven products are available on the Raven web site. At Raven Industries, we ...

7 INTRODUCTION KIT CONTENTS This section contains a list of the components that are included in the RS1 HDU kit. Before beginning the system installation, compare the items in the kit with the components on this list. If you have questions about the kit, contact your Raven dealer. FIGURE 1. RS1 HDU Installation Kit (P/N 117-5032-109 Rev. C) 7 +  1  1  1  1  1  1  ...

FIGURE 2. Hydraulic Installation Kit (P/N 117-0199-081 Rev. D) FIGURE 3. Wheel Angle Sensor Kit (P/N 117-0192-049 Rev. E) 2 6 PART # QTY DESCRIPTION 333-0012-028 1 FTG R ., ADAPTER, SWIVEL RUN TEE, -8 O FS M/M/F 333-0012-051 1 FTG 4 - E ., PLUG, - O RING, INT RNAL HEX 333-0012-069 3 FTG R ., ADAPTER, SWIVEL RUN TEE, -6 O FS M/M/F 333 ...

9 CHAPTER 3HYDRAULIC SYSTEM INSTALLATION WARNING Hydraulics are under pressure. Care should always be taken with a system that has been pressurized. Before beginning the RS1 hydraulic installation, turn off the machine and relieve pressure by turning the steering wheel left and right. When disconnecting or purging hydraulic hoses, be aware that the hydraulic fluid within the machine’s system may be extremely hot and under h ...

INSTALL FITTINGS ON THE STEERING VALVE Before mounting the steering valve (P/N 334-0003-088) on the machine, install the proper fittings in the valve. This prepares the valve for installation and simplifies the hose connection process later in the procedure. FIGURE 1. Fittings Installed on the Steering Valve Fitting Part Number Port Fitting - - ...

11 HYDRAULIC SYSTEM INSTALLATION INSTALL FITTINGS ON THE DUAL TRANSDUCER HYDRAULIC MANIFOLD FIGURE 2. Fittings Installed on the Flow Switch 1. Install a -6 ORFS (M) to -6 SAE O-ring (M) straight adapter fitting (P/N 333-0012-084) in Ports A2 and B3 of the dual transducer hydraulic manifold (P/N 334-003-085). 2. Install the pressure transducers in Ports A1 and B1 of the dual transducer hydraulic manifold. MOUNT THE STEERING VALVE INSTA ...

FIGURE 4. Mounting Bracket Installed 2. Mount the hydraulic valve mounting bracket (P/N 107-0171-705) to the machine’s radar bracket using the bolts removed in step 1. MOUNT THE STEERING VALVE FIGURE 5. Steering Valve Installed on Mounting Bracket 1. Mount the steering valve (P/N 334-0003-088) to the valve mounting bracket (P/N 107-0171-705) ...

13 HYDRAULIC SYSTEM INSTALLATION FIGURE 6. Pressure Hose Installed 3. Install a -6 ORFS M/M/F swivel run tee adapter fitting (P/N 333-0012-069) on the steel pressure line. 4. Connect the machine’s pressure hose to the opposite end of the installed tee fitting. 5. Install the 90° end of the supplied hydraulic hose (P/N 214-1000-657) on the 90° end of the installed tee fitting. 6. Connect the straight end of the installed hydraulic ...

INSTALL THE LEFT AND RIGHT STEERING HOSES 1. Locate and disconnect the machine’s left steering hose from the right steering cylinder. NOTE: The left steering hose is connected to the fitting located closest to the center of the machine. 2. Route and connect the left steering hose to the Port A2 of the installed flow switch (P/N 334-0003-085). ...

15 HYDRAULIC SYSTEM INSTALLATION HYDRAULIC SYSTEM DIAGRAM Before RS1 Installation After RS1 Installation Connect between steel line and hose Dual Transducer Hydraulic Manifold Right Steering Cylinder Left Steering Cylinder Pump Machine’s Steering Orbital Machine’s Steering Orbital Pump Steering Valve ...

...