ROHO JetStream Pro Manual 

Text of ROHO JetStream Pro Manual 

JetStream Pro™ Lateral Pads

Operations Manual s h a p e f i t t i n g t e c h n o l o g y ® PROVIDER: THIS MANUAL MUST BE GIVEN TO THE USER OF THIS PRODUCT. USER: BEFORE USING THIS PRODUCT, READ THIS ENTIRE MANUAL AND SAVE FOR FUTURE REFERENCE. Manuel d’utilisation des coussins latéraux JetStream Pro™ FOURNISSEUR : CE MANUEL DOIT ÊTRE REMIS À L’UTILISATEUR DE CE PRODUIT. UTILISATEUR : AVANT D’UTILISER CE PRODUIT, LIRE CE MANUEL EN ENTIER

TABLE OF CONTENTS

Intended Use 2 Warnings & Precautions 3 Parts Detail 4 Attachment & Adjustment Instructions 5-6 Cleaning and Disinfecting 7 Maintenance 7 Disposal 7 Warranty / Contact Information 8 ©The ROHO Group, Inc. 2007 The following are trademarks and registered marks of The ROHO Group, Inc.: ROHO®, shape fitting technology®, and JetStream Pro®. The ROHO Group

The JetStream Pro Lateral Pads are designed to assist

in maintaining functional posture, as well as promote stability. JetStream Pro Lateral Pads are designed to be used only with the JetStream Pro Adjustable Back Replacement System. The Pads come in Large (Swing Away or Stationary) and Ac- tive (Stationary only) sizes. The Pads consist of aluminum hardware covered by foam and a removable nylon cover, and attach to the Lateral Bracket. Each

• THIS LATERAL PAD OPERATIONS MANUAL IS SUPPLEMENTAL TO AND

DOES NOT REPLACE THE JETSTREAM PRO BACK ATTACHMENT OR ADJUST- MENT PROCEDURES. • As with any addition to your wheelchair, the Lateral Pads may affect the stability of the wheelchair. Consult with your clinician. • Check screws, bolts, brackets, and hinges for wear, breakage, and tight- ness daily. Retighten loose screws following the Attachment Instructions in this manual. DO NOT continue to

A. Lateral Bracket - Comes in Standard (left or right) and Low

sizes. Attaches Pad to inside of Carbon Fiber Shell. B. M6 x 20 mm screws - Used to attach Lateral Bracket to carbon fiber shell. Qty. 2 per Lateral Bracket. C. Washers - Used to attach Lateral Bracket to carbon fiber shell. Qty. 2 per Lateral Bracket. D. Nuts - Used to attach Lateral Bracket to carbon fiber shell. Qty. 2 per Lateral Bracket. E. M5

ATTACHMENT & ADJUSTMENT INSTRUCTIONS

Notes: • Before installation, remove existing JetStream Pro Back, leaving the Bracket Clamps in place on the wheelchair back posts. Note existing height, depth and angle orientation before removing the Carbon Fiber Back. • Install Lateral Pads before the JetStream Pro Back is installed on wheelchair. • After Lateral Pads are installed but before Lateral Pad height, width and angle adjustments are made, install and

PAD / COVER REMOVAL

STEP 1. Loosen each screw (M5 x 10mm) (part E) from Lateral Bracket (part A) using 3mm Allen wrench. STEP 2. Remove each screw (M5 x 10mm) (part E) and Pad (part F). STEP 3. Repeat steps 1-2 for opposite side. STEP 4. On the side opposite of the bracket, pull the cover (part G) over the edge of the foam & remove cover. NOTE: Use 3mm Allen wrench. ATTACHMENT & ADJUSTMENT INSTRUCTIONS PAD HEIGHT ADJUSTMENT STEP 1. Remove each screw (M5 x

CLEANING & DISINFECTING

Cleaning and Disinfecting are two separate processes. To be effective, cleaning must precede disinfecting. Cleaning the Cover: Remove the cover by following instructions on the Attach- ment & Adjustment Instructions Page. Machine wash in hot water. No bleach. Tumble dry low. Cleaning the Brackets and Hardware: Using a soft cloth, hand wash the brackets and hardware with mild soap and warm water. Rinse thorougly. Towel dry with a so

ROHO Wheelchair Owners Instructions: