Riello ricloud Quick Start Manual

WiFi Box: Wireless (only main sup- ply) In this installation the OTBus confi- guration is not working. WiFi Box RF internet WiFi WiFi 230 V BeSMART server TA TA RiCLOUD INSTALLATION B Ricloud: NOT cabled (Wireless) WiFi Box: Wired WiFi Box BeSMART server internet WiFi WiFi RF RF 230 V TA RiCLOUD WiFi Box BeSMART RF SET PROG RESET ESC MODE BeSMART server internet WiFi WiFi 230 V RF OT Note: for all other types of different installation refer to the installer manual.

WiFi Box: Wireless (only main supply) TA WiFi Box 230 V RiCLOUD WiFi OT WiFi Box WiFi 230 V RiCLOUD

WiFi Box: Wireless (only main supply) TA Boiler RF receiver 230 V RiCLOUD RF OT Boiler RF receiver 230 V RiCLOUD RF

WiFi Box: Wireless (only main supply) TA WiFi Box 230 V RiCLOUD WiFi Boiler RF receiver 230 V RF OT WiFi Box WiFi 230 V RiCLOUD Boiler RF receiver 230 V RF

system WiFi Box: Wireless (only main supply) Ricloud: Generic wireless Cooling system WiFi Box: Wireless (only main supply) TA RF single 230 V RiCLOUD zone heating coupling RF single 230 V RiCLOUD zone cool coupling TA

system WiFi Box: Wireless (only main supply)

generic heat source OTBus OTBus G W Y R Rc Wireless ON/OFF Ricloud, single RF receiver to control a heat zone OTBus OTBus G W Y R Rc Wired ON/OFF Ricloud, to control a generic fan source OTBus OTBus G W Y R Rc OTBus OTBus G W Y R Rc OT= OTbus communication wires G= Fan/ventilation connection wire W= Heating connection wire Y= Cooling connection wire R= External power wire Rc= (cabled as default to R pin) redirection of external power to other pin

B Do not install above heat sources C Avoid direct sunlight D Install at the correct height Before installation • Refer to the appliance manual to ensure that the Ricloud thermostat is compatible with your boiler. • The Ricloud wireless thermostat can be installed almost everywhere within the home, however please refer to the adjacent diagrams for guidance when deciding on a suitable location. • The Ricloud thermostat can also be used to replace an existing hard-wired thermostat (please check appliance manual to ensure compatibility). • Switch off and isolate the appliance and any external controls from the electrical supply, before carrying out the installation. Tools required for the installation • Phillips screwdriver • Small flat blade screwdriver • Combination pliers 1,5m A B C D

9 9 If its intended to re-use any existing wiring; you should refer to the appliance manual to ensure compatibility. 9 9 If the Ricloud thermostat is a wireless control ( B installation). Isolate any redundant wiring and ensure it does not interfere with the fitments of the Ricloud control Separate the Ricloud from the wall plate. Fix the wall plate to the wall using the supplied screws (screw head inside proper location).

the respective wiring to the relevant terminals on the Ricloud control. 9 9 Please refer to the appliance installation manual and the Ricloud manual for specific information on hard- wired connections ( A installation). TA ON/OFF Insert two ‘AA’ type batteries (supplied), into the battery compartment. 9 9 Insert the batteries, observing the correct polarity as indicated. Re-attach the Ricloud thermostat to the wall plate by aligning and then pressing firmly around the outer edges. AA AA

Connect the (supplied) USB WiFi Box cable to the boiler OTBus connection (for specific boilers) or to the boiler room thermostat connection (TA or ON/OFF). 9 9 For the electrical connection and the technical specifications, please refer to the installation manual (OT PCB plug supplied as standard). Attach the WiFi box to the appliance casing, using the magnetic pad located on the rear of the WiFi Box. Please check the ambient temperature is according the product specification as indicated on the installation manual. In case of low or null WiFi signal and with boiler RF re- ceiver or WiFi Extender installed, place the WiFi Box in an ambient with a good WiFi signal (above 40%). WPS/Smartlink Outputs Boiler

BOILER socket of the WiFi Box. Using the mini USB cable and power adaptor (supplied); connect the WiFi box to an adjacent electrical socket . WPS/Smartlink Outputs Boiler USB Outputs Boiler

Download and install the Ricloud APP on your Smartphone or tablet. Create a user account following the steps indicated on the APP. Link your user account to the ‘ID WiFi’ code that’s located on the side of the WiFi Box.

WPS/Smartlink Outputs Boiler WPS/Smartlink Outputs Boiler A WiFi Box If required, it is possible to couple a boiler receiver or additional thermostats to the WiFi box using the following procedure: press and hold the WiFi LED button on the WiFi box until both red and green LEDs are flashing simultaneously. Place the item that is to be coupled, into the ‘coupling’ mode (see Ricloud instruction manual). When the coupling process has been completed, the system will automatically return to the normal operating condition. A WiFi LED button