Sealey PC195SD.V2 Manual 

Stainless Drum model no: PC195SD.V2 Thank you for purchasing a Sealey product. Manufactured to a high standard, this product will, if used according to these instructions, and properly maintained, give you years of trouble free performance. IMPORTANT: PLEASE READ THESE INSTRUCTIONS CAREFULLY. NOTE THE SAFE OPERATIONAL REQUIREMENTS, WARNINGS & CAUTIONS. USE THE PRODUCT CORRECTLY AND WITH CARE FOR THE PURPOSE FOR WHICH IT IS INTENDED. FAILURE TO DO SO MAY CAUSE DAMAGE AND/OR PERSONAL INJURY AND WILL INVALIDATE THE WARRANTY. KEEP THESE INSTRUCTIONS SAFE FOR FUTURE USE. 1. Safety 1.1. ELECTRICAL SAFETY ‰ ‰ WARNING! I ...

Airflow:....................................................................126mtr³/hr Drum Size:.......................................................................20ltr Drum Type:..................................................... Stainless Steel Weight:.............................................................. ...

‰ ‰ WARNING! Make sure the vacuum is unplugged (fig.2.1). 5.1.1. Release the barrel locks (fig.2.2). 5.1.2. Lift the top cover assembly from the dust barrel (fig.2.3). 5.1.3. Install Hepa filter in the correct position (fig.2.4). 5.1.4. Put the top cover assembly on the dust barrel and lock it in place with the clips (fig.2.5). 5.1.5. Insert the hose connector into the air inlet as shown, make sure the connector is tightly fastened (fig.2.6). 5.1.6. Connect the tube to the hose assembly (fig.2.7). 5.1.7. Connect three tubes (fig.2.8). 5.1.8. Connect tubes and floor nozzle (fig.2.9). 5.1.9. Plug the machine in (fig.2.10). 5.1.10. swi ...

6.1.2. Turn off the machine (fig.3.2). 6.1.3. Unplug the cable (fig.3.3). 6.1.4. Release the barrel lock (fig.3.4). 6.1.5. Raise the top cover assembly from the dust container (fig.3.5). 6.1.6. Empty the debris from the barrel (fig.3.6). 7. Hepa Filter cleaning 7.1. The Hepa filter should be washed using clean warm water when it is covered with dust. If very soiled use a mild detergent to wash the filter. 7.1.1. Remove hepa filter (fig.4.1). 7.1.2. Shake off dust (fig.4.2). 7.1.3. Wash allow to dry before installing (fig.4.3). 8. Wet Vacuuming ‰ ‰ WARNING! Make sure the vacuum is unplugged (fig.5.1) ...

9.1.1. Unscrew the hose from the suction port (fig.6.2). 9.1.2. Insert the hose assembly into the blower socket (on the back of the top cover), rotate it to the right and tighten it (fig.6.3). 9.1.3. Plug in the machine (fig.6.4). 9.1.4. Switch on the machine (fig.6.5). 9.1.5. The unit will now blow through the vacuum hose and can be used to clear obstructions within the hose (fig.6.6) ‰ ‰ WARNING! Before using the blower function, make sure the container is empty ‰ ‰ WARNING! Always wear safety goggles before using the blower. Keep bystanders away from blowing debris and wear ...

 01284 757500  01284 703534  [email protected]  www.sealey.co.uk Environment Protection Recycle unwanted materials instead of disposing of them as waste. All tools, accessories and packaging should be sorted, taken to a recycling centre and disposed of in a manner which is compatible with the environment. When the product becomes completely unserviceable and requires disposal, drain any fluids (if applicable) into approved containers and dispose of the product and fluids according to local regulations. Weee Regulations Dispose of this product at the end of its ...