Linak DL8 Operation & User’s Manual

LINAK.COM/DESKLINE DL8, DL9, DL10 and DL11 system with CBD6S User manual all-guides com ...

Contents Preface ............................................................................................................................................. 3 Valid for............................................................................................................................................. 4 Important information............................................................................................................... ...

Preface Dear User, We are delighted that you have chosen a product from LINAK®. LINAK systems are high-tech products based on many years of experience in the manufacture and development of actuators, electric control boxes, controls and chargers. This User Manual does not address the end-user. It is intended as a source of information for the manufacturer of the equipment or system only, and it will tell you how to install, use and maintain y ...

Valid for: This User Manual is valid for the following products: (See the first 3 - 5 characters on the label) Columns: DL8, DL9, DL10 or DL11 (1 - 3 (4)) Control boxes: CBD6S 200W, CBD6S 300W Controls: DP1U/DPF1M (if memory function is required) DP1C//DPT/DPF1C (if memory function and display is required) or DPA/DPB/DP1K/DP1V/DPF1K (if only up/down is required) or DPF1D (if display is required). ...

Safety instruction General Important information Important information on LINAK® products can be found under the following headings: Warning! Failure to comply with these instructions may result in accidents involving serious personal injury. Failing to follow these instructions can result in the product being damaged or being destroyed. Safe use of the system is possible only when the operating instructions are read completely and the instru ...

Before installation, re-installation, or troubleshooting • Stop the DL8/DL9/DL10/DL11 • Switch off the power supply and pull out the mains plug. • Relieve the DL8/DL9/DL10/DL11 of any loads, which may be released during the work. Before start-up: • Make sure that the system has been installed as instructed in this User Manual. • Make sure that the voltage of the control box is correct before the system is connected to the main ...

Only for EU markets This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision. Only ...

Repairs In order to avoid the risk of malfunction, all DESKLINE® repairs must only be carried out by authorised LINAK service centres or repairers, as special tools must be used and special gaskets must be fitted. Products under warranty must also be returned to authorised LINAK service centres. Further information on DESKLINE warranty can be found on the LINAK website www.linak.com/warranty. Warning! If any of the DESKLINE® products are ope ...

Misc. on the DESKLINE® DL8/DL9/DL10/DL11 system Warranty This DESKLINE product is subject to warranty pursuant to the terms of LINAK DESKLINE Warranty Paper, available on the LINAK website www.linak.com/warranty. Maintenance Clean dust and dirt on the outside of the system at appropriate intervals and inspect them for damage and breaks. Inspect the connections, cables, and plugs and check for correct functioning as well as fixing points. Serv ...

C/N 4008003 Conforms to UL962 Cert. to CSA Std. C22.2 No. 68-09 ETL Recognized Component mark for Canada and United States C/N 4008004 Conforms to UL962 Cert. to CSA Std. C22.2 No. 68-09 ETL Recognized Component mark for Canada and United States C/N 4008005 Conforms to UL962 Cert. to CSA Std. C22.2 No. 68-09 ETL Recognized Component mark for Canada and United States C/N 4008671 Conforms to UL962 Cert. to CSA Std. C22.2 No. 68-09 ETL Recognize ...

Description of the DESKLINE® system Each DESKLINE® actuator/column is equipped with a motor and parallel/memory drive is ensured by means of software in the CBD6S that also takes account of an uneven load on the desk. Soft start and stop are also part of this software, which ensures a soft start and stop when adjusting the desk. Application of the DESKLINE® system: Irrespective of the load the duty cycle 10% ~ 6 min./ hour or max. 2 min. a ...

Mounting guidelines for the DL8/DL9/DL10/DL11 system Mounting guidelines for DL8/DL9/DL10/DL11 (motor housing) The motor housing is supplied with 6 M6 threaded holes meant for mounting onto the desk frame. We advise you to fasten the desk frame by means of 6 pcs. M6 screws of a good quality (min. 8.8) and a suitable length, which must not go further into the motor housing than max.10 mm. The thrust moment must not exceed 7.5 Nm. It is recomme ...

Mounting guidelines for the DL8 and DL9 (foot part) The DL8/DL9 is supplied with 4 M6 threaded holes for the mounting of the foot. We advise you to fasten the foot by means of 4 pcs. M6 screws of a good quality (min. 8.8) and of a suitable length, which must not go further into the DL8/DL9 column than 20 mm. The thrust moment must not exceed 10 Nm in the bottom plate thread. The 4 holes in the bottom of the DL8/DL9 are placed on a Ø 42 mm di ...

Mounting guidelines for the DL11 (foot part) The DL11 is supplied with 4 M6 and 2 M8 threaded holes for mounting of the foot. We advise you to fasten the foot by means of 4 pcs. M6 screws or 2 pcs M8 screws of a good quality (min. 8.8) and of a suitable length. The holes in the foot ought to be sufficiently larger than ø6 so that it is possible to bring the foot to a level line at assembly/mounting. The 4 M6 holes in the bottom of the column ...

Mounting of the desk (misc.) As the desktop amplifies the sound, we advise you to place a vibration/ shock absorbing material between the desktop and the desk frame. With a desktop thickness of 25 mm, it is necessary for the lowest edge of the lifting unit to be mounted max. 15 mm above floor level to obtain a desk height of only 600 mm in the lowest position. If e.g. 2 mm vibration absorbing material is placed between the desktop and the des ...

LINAK recommends that the DESKLINE® DL8/DL9/DL10/DL11 system should only be used in push applications with the motor housing uppermost. Placement of a monitor directly above the motor may cause malfunction of the monitor. Magnets inside the motor may interrupt the picture on the monitor depending on the distance and type of monitor. If this is the case the problem may be solved by placing an iron plate/tube or another magnetic material, some ...

Mounting guidelines CBD6S (SMPS) The control box is to be fastened with 1 - 2 screws with a head diameter between ø 8 and ø 10 mm. Out of regard for the tension surface ø 10 mm is preferable due to lower surface tension. See drawing appendix for placing of mounting holes and the space the CBD takes up. The CBD must not be packed in heat insulating material, but must be placed so that it can emit waste heat into the surroundings. There are ...

Figure 1 Electrical connection of the DL8/DL9/DL10/DL11 system The systems is to be connected as shown on figure 1. Each DL8/DL9/DL10/DL11 is to be connected to the sockets on the control box by means of the motor cables, which have a 6-pin plug in each end. Finally the mains cable is to be mounted and power switched on. Please note that the control box must only be connected to the voltage stated on the label. DP DL8/DL9/DL10/DL11 Hook for c ...

Initialisation of the DESKLINE DL8/DL9/DL10/DL11 parallel system Press the down button and the legs/actuators run down to the “buffer” causing cut-off due to excess current. Hereafter they run approx. 3 mm (from software version 1.66, previosely 5 mm) upwards and thereby free of the “buffer”. When the movement stops, the system is initialised. During the entire initialisation procedure, the down button must be pressed down. If the but ...

Anti-Collision™ The function (anti-collision) is an option for the standard CBD6S (SMPS) control box. A system with anti-collision can limit material damages on a desk if a collision with a solid object should occur. Enabling the anti-collision To enable the anti-collision function a little plug called a dongle must be mounted in one of the 2 control ports. The function is only active when the dongle is mounted. – If you remove the dongle ...