Objecto FLOW F1 Operation & User’s Manual

these instructions when using the product. IMPORTANT SAFETY INSTRUCTIONS When using electrical appliances, basic precautions should always be followed to reduce the risk of fire, electric shock, and injury to persons, including the following: 1. Read all instructions before using this product. 2. This product is designed for home use only. Do not use for any other purpose. 3. Extreme caution is necessary when any fan is used by or near children or invalids and whenever the product is left operating and unattended. 4. Always unplug the product when not in u ...

• the power cord. Do not allow children to use this product by themselves, and keep the product and power cords • out of the reach of small children. Do not plug in or unplug the product while your hands are wet. • Do not apply water or sprinkle water over the fan. • Do not operate without installing the blades and guard. • Use only with the designated power supply 110 – 120 V. • If you notice anything unusual during operation (burning smell, smoke, etc.), immediately stop • use, and unplug the power cord. Insert the power plug al ...

Base Remote control receiver Operation unit Remote control storage compartment Affi x with the magnet on the back of the remote control Stand Front guard vent (Blades inside) Handle Front Remote control Rear guard vent Main unit Rear DC cord DC plug AC adapter AC adapter ...

Remote control ④ Manual operation button The functions of the buttons on the main unit and the remote control are the same. (A) Power button Start / stop operation. (When all lamps are lit, the fan is in “turbo” mode with the strongest air fl ow) (B) Air fl ow button Adjust the air fl ow during operation. (C) Oscillate button Start / stop Oscillate operation. (D) Timer button Set the on / off timer time. (E) Rhythm / Night-time air fl ow button Switch between Rhythm and Night-time air fl ow functions. * Press and hold (3 seconds or more) to set the lamp to ...

Preparation Before Use Put the battery in the remote control 1. 2 1 3 4 1 Pull out the battery box from the remote control unit. Pull out the battery from the battery box. 2 Put a coin type lithium battery into the battery box, paying attention to the orientation of the battery. Put the + side of the battery facing up. 3 Insert the battery box into the remote control unit. 4 Insert until it clicks. Usable Range of Remote Control About 16 feet straight from the front of the main unit • . About 30° left and right from the front of the main unit • . If there is an obstacle between the remote control and the main ...

Starting Operation 1. When you press the power button on the main unit or the remote control, operation starts. During normal use, operation starts with the previous settings for air flow and • Oscillate, using the memory function. When you first press the • power button on the main unit or the remote control after plugging the power plug into the outlet, operation starts with very weak air flow and no Oscillate. Adjusting the Air Flow 2. Adjust the air fl ow by pushing the air fl ow button on the main unit or the remote control. Very weak Weak Medium Strong (all lights) Turbo “Turbo” is the ...

4. Oscillate operation starts when you press the Oscillate button on the main unit or the remote control during operation. Press the button again to stop Oscillate operation. Oscillate about 75° You Can Change the Direction Manually. The direction that can be changed is 6 clicks on each side, with 1 click of about 10°, totaling about 60°. CAUTION For safety, change direction with operation stopped. Changing the direction by force may cause damage, malfunction, or abnormal noise, etc. Stop operation 5. Press the power button on the main unit or the remote control during operation to stop operation. ...

By setting the OFF timer, operation can be stopped automatically after the set time. Press the 1. Timer Button During Operation to Set the OFF Timer When you press the timer button on the main unit or remote control during operation, the timer lamp lights up in green and the OFF timer is set. The OFF timer operation time can be set by pressing the timer button on the main unit or remote control. About the Timer Lamp Each time the timer button on the main unit or remote control is pressed, the timer lamp switches as shown below. 1H (1 hour) 2H (2 hour) 4H (4 hour) (Unlit) (Timer cancel) 8H (8 hour) After s ...

3. Press the timer button on the main unit or the remote control several times to turn off the timer lamp. Adjust the Angle Support the handle, push the top or bottom of the front guard, and slowly move the fan up or down. Before adjusting the angle, be sure to stop operation and check that the blades • have stopped. Adjust while pressing with one hand so that the main unit does not fall. • Front Front Rear Rear Downward You can adjust the angle up to about 45° Upward You can adjust the angle up to about 90° Handle Using as a Circulator If you use the fan together with an air conditioner to circulate the indoor a ...

WARNING When cleaning the product, be sure to unplug the power cord from the outlet. CAUTION Do not use household detergent, thinner, benzine, alcohol, or polish, etc. • under any circumstances. Do not wash the fan by sprinkling water over the main unit or AC adapter. • (Doing so may cause electric shock or malfunction.) Internal Cleaning Remove the front guards and blades as follows and clean the interior. Front guard Blade-mount spinner Blades Rear guard Motor shaft Recess (2)(3) (4) Removal (1) Remove each screw at the two lock release switches on the top of the front guard. Lock release switch all-guide s.com ...

front guard forward to remove it. Lock release switch (2) (2) (3) Turn the blade-mount spinner clockwise and remove the blades. Mounting (4) To mount the blades, fit them to match the shape of the motor shaft, firmly turn the blade-mount spinner counterclockwise, and tighten. Fit the blades to match the shape of the motor shaft (4) (5) Place the hook at the bottom of the front guard in the recess at the bottom of the rear guard and then fit the lock release switch on the top. Recess Rear guard Front guard (5) (5) Storage Clean by removing dust on the front and rea ...

This fan can be stored compactly by folding when not in use. 1 Stop operation, unplug the power plug from the outlet, and remove the AC adapter from the main unit. 2 Hold the base and the handle, and slowly move the stand down toward the base side. (Reverse of “2. Hold the base and raise the stand” on page 6) The fan can be stored in a narrow space. (Store the remote control and AC adapter in an appropriate place) When folded, do not leave leaning against a wall in an area where people * regularly pass. CAUTION Be careful not to pinch your fingers when folding. • Do not carry by holding any part other than the h ...

WARNING This product can be disassembled and repaired by qualified repair technicians only. If you find any problems, follow the troubleshooting procedures below. Problem Primary Cause Solution The power does not turn on. The DC plug of the AC adapter is disconnected from the DC jack. Plug the DC plug into the DC jack. The AC adapter is unplugged from the outlet. Plug the AC adapter into the outlet. The air fl ow is weak. Dust accumulates in the guards. Remove the dust with a vacuum cleaner. The blades do not turn. The blades are not • installed correctly. The blades hit the • guard. Correctly instal ...

Power supply 110 – 120 V, 50/60 Hz Power consumption 10 W AC adapter cord length Approx. 70 inches Size Width 13 in × Depth 12 in × Height 29 in Weight Approx. 8.4 lbs (body only) Accessories User’s Manual / Warranty × 1, AC adapter × 1, Remote controller × 1, Coin type lithium battery × 1 Due to a continuous process of product improvement, the specifications and * other information are subject to change without notice. ...

Thank you for selecting our Products. Please carefully read the User’s Manual furnished with this product. We believe that you will be very satisfi ed with your purchase. We will provide the following LIMITED WARRANTY to you as the original purchaser. Should service be necessary for any reason due to manufacturing defect or malfunction during the 90 days period, OBJECTO will provide carry-in repair service at our FACTORY SERVICE CENTER at no charge, and for the duration of the extended 9 months parts warranty period will replace the defective part only, not including labor, provided the defect or malfunction is veri� ...

Esta sección presenta información de seguridad importante. Siga estas instrucciones siempre que utilice el producto. INSTRUCCIONES DE SEGURIDAD IMPORTANTES Al utilizar aparatos eléctricos, es necesario tomar algunas precauciones básicas con el fin de reducir el riesgo de incendios, descargas eléctricas y lesiones en las personas. Entre estas se incluyen: 1. Lea todas las instrucciones antes de utilizar este producto. 2. Este producto se ha diseñado únicamente para su uso en hogares. No lo utilice para otros fines. 3. Es necesario tomar la máxima precaución cuando un ventilador es utilizado cerca de niño ...

• introducido por completo en el tomacorriente. No raspar, dañar, modificar, doblar por la fuerza, jalar, retorcer, unir/sujetar con abrazadera ni • colocar objetos pesados sobre el cable de alimentación. No permitir que los niños utilicen este producto por su cuenta, y mantener el producto y los • cables de alimentación fuera del alcance de niños pequeños. No enchufar ni desenchufar el producto si tiene las manos mojadas. • No mojar el ventilador ni dejar que caiga agua sobre él. • No utilizar sin instalar las aspas y la carcasa. � ...

Base Receptor del control remoto Unidad de funcionamiento Compartimento de almacenamiento del control remoto Fijar con el imán de la parte trasera del control remoto Pie Abertura de la carcasa frontal (aspas en el interior) Asa Parte frontal Control remoto Abertura de la carcasa trasera Unidad principal Parte trasera Cable de CC Enchufe de CC Adaptador de CA Adaptador de CA ...