NTI XTENDEX Series Operation & User’s Manual

with Video Wall Support User Manual Transmitter (Local Unit) XTENDEX® Series Receiver (Remote Unit) ...

Package Contents: .............................................................................................................................. 1 Applications: ........................................................................................................................................ ...

monitors) access to a USB computer up to 492 feet (150 meters) over a Gigabit network using a single CAT5e/6 cable. The extender consists of the ST-IPUSBVD-L-VW Local unit (Transmitter (TX)) that connects to a computer and also supplies video to local VGA and DVI monitors; and the ST-IPUSBVD-R-VW Remote unit (Receiver (RX)) tha ...

Point-to-Many Connection Many-to-Many Connection Local Unit Remote Units Remote Units Local Units 3 ...

Receiver (Remote Unit) Panel Button Function: Button - + Menu Reduce Number Increase Number Menu/Cancel Short Press Enter Press for 1 second Carry Decomposition Press for 3 seconds Lock/Unlock Panel Buttons (When OSD is not displayed ) Press and hold then power the unit ON Factory Default Engineering Mode Definitions: Reduce Number: decrements the channel or the function ...

apply that selection. Carry: Advances the selected channel in multiples of 10 (Switch channel 2 to 20, then to 200) Decomposition: Decrements the selected channel in multiples of 10 (Switch channel 200 to 20, then to 2) Lock/Unlock Panel Buttons: When locked, panel buttons will not respond to a momentary push. You must press the Me ...

RJ45 LED Status Description LINK (Green) On Ethernet connected ACT (Orange) Flash Data transmission MSG LED Status Indication: Times Status Always ON IR control, RS232 control, system setting activity is occurring 2 IR Control disabled 3 Transmitters channel conflict 4 DHCP server not found 5 Restore to factory defaults 6 Engineering mode/Firmware update mode 7 Manufacture setting mode 8 Aux system stopped 9 Aux system f ...

For the cable between the transmitter and receiver, use high quality CAT.5e UTP/STP/FTP or CAT.6 UTP cable. The transmission distance will be affected by equipment (router, Ethernet switch, hub), cable quality, routing the cable over noise generating devices, etc. When using CAT.5e/CAT.6 cable to connect the transmitter and receiver directly (without an Ethernet switch), the maximum transmission distance is 150M. You can als ...

For example MAC XX:XX:XX:XX:12:AB, the default IP address will be169.254.18.171 You could also set the units to DHCP or Auto IP. Please refer to web setting chapter: “IP Setting” (Page 20). In Auto IP mode it will assign 169.254.X.X (subnet mask 255.255.0.0) to transmitters and receivers when no DHCP server i ...

The IR infrared remote control can be used to preset channel selection and other menu functions. Using the IR remote control, aim at the front panel of the receiver or the external IR receiver cable. When first using the remote control or after changing the battery in the remote control, the IR remote control and the equipment Remote ID must be using same ID. The default Remote ID for the transmitter is 7, and for the receiver it ...

Select Channel: Mode 1: use  or or or  to select channel and press ENTER to confirm. Mode 2: enter the channel number and press ENTER to confirm the input channel. Select Menu Function: Mode 1: press MENU then use  or  or  or  to select function, press ENTER to confirm. Mode 2: press MENU, then input function number as below, press ENTER to confirm. Wake Up Receiver: In screen saver mode (30 seconds with ...

Video Wall setting 0 = Disable 1 = Enable 1 1 26 CEC Function CEC Extender setting (4K only) 1 1 27 Keyboard Mouse Function Keyboard Mouse Extender setting 1 1 30 Button Control Button Control setting 0 = Disable 1 = Enable 1 1 31 Button Lock Button Lock 0 0 32 IR Control IR Control setting 1 1 33 IR Control ID IR Control ID setting 0 ~ 9 = IR Control ID 10 = User Defined Controller 8 7 34 RS232 Control RS232 Control setting 0 = Di ...

1 = 57600 bps 2 = 38400 bps 3 = 19200 bps 4 = 9600 bps 5 = 4800 bps 6 = 2400 bps 7 = 1200 bps 8 = 600 bps 9 = 300 bps 0 0 55 Auxiliary Newline Auxiliary Newline setting 0 = Linux (0x0A) 1 = Windows (0x0D, 0x0A) 2 = Mac (0x0D) 3 = Other (0x0A, 0x0D) 1 1 56 Auxiliary Trigger Auxiliary Trigger setting 1 1 57 Device No Device No. for RS232 control 0 ~ 999 0 X 58 Group No Group No. for RS232 control 0 ~ 99 ...

Outer Width of Monitor 0~65000 (0.1mm) 0 X 9 Monitor Outside Height Outer Height of Monitor 0 X 9 Monitor Viewable Width Width of Viewable Area 0 X 9 Monitor Viewable Height Height of Viewable Area 0 X 100 Stretch Type Screen Stretch Type 0 = Auto 1 = Stretch Out 2 = Fit In 2 X 101 Rotate Screen Rotation and Mirror 0 ~ 7 0 X 102 Vertical Shift Screen Vertical Shift 400 = Default 399 ~ 0 = shift up 401 ~ 801 = shift down 400 X 103 Ho ...

number already exists the connection will be interrupted.  Menu 62 Channel Name will show full name instead of number only . The position of the channel name will be at center of screen. The Channel name can set by RS232 command or imported from telnet port.  Menu 75 Message Redirect forwards MENU message to Transmitter RS23 ...

Previous value Enter Confirm * or Esc or Clear Cancel / Call MENU Press Clear four times then press Enter Call MENU Keypad Control: You can use a number pad to emulate the IR Remote Operation. 1. Use a DB9 cable to connect the RS232 port of the Local or Remote Unit and that of the PC. Make sure that the PC has a number pad or a keyboard with number pad connected. Pinouts for the DB9 ...

Command Parameters Description Remark CHANNEL ? Show current channel number Transmitter does not support parameter NAME Receiver does not support parameter CHECK [ 0~999 ] Switch to specified channel [ 0~999 ] NAME ? Check current channel name [ 0~999 ] NAME “string” Set channel name, 28 character MAX NAME ? Show channel name setting NAME [ ENABLE | DISABLE ] Enable/disable channel name NAME CLR Clear all channel nam ...

Set position in column STRETCH ? Status of stretch type STRETCH [ 0~2 ] Set stretch, 0 = Auto, 1 = Stretch Out, 2 = Fit ROTATE ? Status of rotate type Transmitter supports FUNC only ROTATE [ 0~7 ] Set rotate, 0 = default SHIFT_V Status of vertical shift SHIFT_V [ 0~399 | 400 | 401~801 ] 0~399: up, 400:default, 401~801: down SHIFT_H ? Status of horizontal shift VIDEOWALL SHIFT_H [ 0~399 | 400 | 401~801 ] 0~399: up, 400:default, 401~801: down ...

Transmitter does not support parameter SELECT SELECT ? Status of EDID setting SELECT [ 0~3 ] 0=HDMI, 1=DVI, 2=VGA, 3=Loop Out HDMI CTRL ? Status of HDMI 5V control Transmitter does not support parameter CTRL CTRL [ ENABLE | DISABLE ] Enable/disable HDMI 5V control HDCP ? Status of HDCP Always On HDCP [ 0~2 ] 0=Disable, 1=HDCP 1.4, 2=HDCP 2.2 SCREEN ? Status of screen settings Transmitter does not support ...