Datalogic ENC-58 PROG Instruction Manual

Via Lavino, 265 40050 - Monte S. Pietro Bologna - Italy © 2014 Datalogic Automation S.r.l. � TUTTI I DIRITTI RISERVATI. � Protetto nei limiti massimi consentiti dalla legge degli Stati Uniti d'America e internazionale. Sono vietate la copia o le modifiche di questo documento senza la previa autorizzazione scritta da parte di Datalogic Automation S.r.l. Datalogic and the Datalogic logo are registered trademarks di Datalogic ...

2 - Identification ................................................................................................................ 3 3 - Mounting instructions ................................................................................................... 4 3.1 Solid shaft encoders ...................................... ...

In this guide, to make it easier to understand and read the text the following typographic and iconographic conventions are used:  parameters and objects both of the device and the interface are coloured in ORANGE;  alarms are coloured in RED;  states are coloured in FUCSIA. When scrolling through the text some icons can be found on the side of the page: they are expressly designed to highlight the parts of ...

operator needs to correctly and safely install and operate the ENC58 programmable incremental encoder. ENC58 programmable encoder from Datalogic Automation is designed to maximize customization and versatility and really allows the operator to get, along with the position information, a complete parametrization and the better configuration that perfec ...

Safety  Always adhere to the professional safety and accident prevention regulations applicable to your country during device installation and operation;  installation and maintenance operations have to be carried out by qualified personnel only, with power supply disconnected and stationary mechanical parts;  device must be used only for the purpose appropriate to its design: use for purposes other than those for ...

– Mounting instructions”.  mechanical installation has to be carried out with stationary mechanical parts;  do not disassemble the encoder;  do not tool the encoder or its shaft;  delicate electronic equipment: handle with care; do not subject the device and the shaft to knocks or shocks;  respect the environmental characteristic ...

Device can be identified through the ordering code and the serial number printed on the label applied to its body. Information is listed in the delivery document too. Please always quote the ordering code and the serial number when reaching Datalogic Automation s.r.l. for purchasing spare parts or needing assistance. For any information on the technical characteristics of the product refer to the technical catalogue. ...

WARNING Installation has to be carried out by qualified personnel only, with power supply disconnected and mechanical parts compulsorily in stop. 3.1 Solid shaft encoders  Mount the flexible coupling 1 on the encoder shaft;  fix the encoder to the flange 2 (or to the mounting bell) by means of screws 3;  secure the flange 2 to the support (or the mounting bell to the motor);  mount the flexible coupling ...

3.2.1 AMT58-H15  Mount the encoder on the motor shaft using the reducing sleeve 8 (if supplied). Avoid forcing the encoder shaft;  fasten the fixing plate 4 to the rear of the motor using two M3 cylindrical head screws 5;  fix the collar 3 to the encoder shaft (apply threadlocker to screw 3). ...

WARNING Electrical connection has to be carried out by qualified personnel only, with power supply disconnected and mechanical parts compulsorily in stop. Never force the rotation of the shaft manually, it could cause irreparable damage! WARNING If wires of unused signals come in contact, irreparable damage could be caused to the device. Please insulate them singularly 4.1 Cable and connectors connections + I2C seri ...

M23 12-pin connector Male Clockwise 4.4 M12 12-pin connector specifications Male Frontal side A coding 4.5 Connection of the shield For signals transmission always use shielded cables. The cable shielding must be connected properly to the metal ring nut 3 of the connector in order to ensure a good earthing through the frame of the device ...

Minimize noise by connecting the shield and/or the connector housing and/or the frame to ground. Make sure that ground is not affected by noise. The connection point to ground can be situated both on the device side and on user’s side. The best solution to minimize the interference must be carried out by the user. You are advised to provide the ground connection as close as possible to the encoder. 4.7 A, B, 0 output c ...

whenever you set a new resolution next to the Resolution parameter or reverse the counting direction. NOTE The width of the 0 pulse can be set next to the Z pulse width parameter. Two options are available: 90° and 180°. Please note that the 0 pulse having a width of 90 electrical degrees is synchronised with A and B pulses, while the 0 pulse having a width of 180 ele ...

clockwise). When the option DOWN is set -Direction = DOWN-, if the Counting direction input has LOW logic level (0VDC) the encoder will provide the increasing count when the shaft is turning counter-clockwise (and the decreasing count when the shaft is turning clockwise); on the contrary if the Counting direction input has HIGH logic level (+VDC) the encoder will provide the incre ...

This encoder provides the zero signal (Index pulse) once per revolution as relative positioning reference (home position, see the Figure on page 9). In this way a unique position can be identified at a well-known point in the 360° revolution of the encoder shaft. The external button located in the rear side of the encoder enclosure allows to set the point in the revolution at which the 0 p ...

4.12 I2C (Inter Integrated Circuit) serial connection The ENC58 programmable encoder is equipped with a serial interface for the parametrization and set-up of the device. The serial interface is a I2C (Inter Integrated Circuit) type interface. To communicate with the encoder, you must connect the device to the personal computer through a USB port using the specific connection cable su ...

ENC58 when you activate the USB connection ! NOTE Before configuring the encoder by means of the programming interface, you must connect it to the personal computer through the KIT ENC58 connection cable. You are required to install the drivers of the USB Serial Converter and the USB Serial Port first. The drivers are available for download at the following address www.da ...

5.1 Configuring the encoder using the software tool ENC58 programmable incremental encoder is supplied with a software expressly developed and released by Datalogic Automation in order to easily programme and configure the device. It allows the operator to set the working parameters of the device and monitor whether the device is running properly. The program is supplied for free and can be installed in any PC fitte ...