MantelMount MM340 Installation Instructions Manual

before you begin. Do not unpack box contents until verifying the requirements listed on page 2–3. U.S. PAT. NO. 8,864,092 INSTALLATION INSTRUCTIONS MM340 Standard Pull Down TV Mount Contains important safety information – please save! MantelMount.com If you need help, call 1.800.897.9755 ext.1 For missing/damaged parts or questions during installation, please contact our Customer Support team at 1.800.897.9755 ext.1 or support@m ...

3 Verify you have the required tools. 2 7/32" 4–5mm 10–14mm AWL DRILL BIT PENCIL LEVEL STUD FINDER WRENCH SOCKET WRENCH POWER DRILL TAPE MEASURER ALLEN WRENCHES 1 Verify TV and mount space meet these criteria: VESA Width: 200-700mm Height: 100-500mm SCREEN SIZE 44" to 80" (Diagonally) 2 Verify MantelMount will fit the wall space. VESA Width: 200-700mm Height: 100-500mm 44" – 80" VESA COMPLIANT Width: 200–60 ...

4 Verify all parts are included. If any parts are missing or damaged, contact Customer Support at 1-800-897-9755 ext.1 before installing. ...

CAUTION / WARNING SPECIAL NOTE REQUIRES TWO PEOPLE DO NOT HELPFUL INFORMATION Symbols Used in this Manual STEP 1 Attach Braces to TV. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PAGE 5 STEP 2 Determine Wall Placement . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . PAGE 7 STEP 3 Attach Mount to Wall. . . . . . . . . . . . . . . . . . . . . . . ...

STEP 1 Attach Braces to TV Select Screws and Spacers. If Spacers {12} are required, choose one of these Screw combinations shown with maximum Spacer usage. 1.3 {02} {01} {10} {10} {10} {10} {11} {11} {11} {12} {12} {10} {12} {10} {12} {12} {12} {12} {12} {12} {12} {12} {12} {12} {03} {05} {04} {06} {08} {07} {09} M5 M6 M8 Test-fit Brace components on back of TV. Place TV screen-side down on a ...

Install the Vertical Braces {31} so that the bottoms of the braces are between 3" to 10" from the bottom of TV, centering the braces vertically as much as possible. {31} 3 to 10 INCHES 1.5 SIDE VIEW {31} VERTICAL BRACES MUST ALWAYS BE INSTALLED HIGHER THAN THE BOTTOM OF THE TV. If the lower VESA holes are less than 3" from the bottom of TV, go to STEP 1.6; otherwise skip to STEP 1.7. If the lower VESA holes a ...

STEP 2 Determine Wall Placement DISTANCE Measure the distance from the bottom of the Vertical Braces {31} (not the Extenders) to the bottom of the TV/ sound bar. 2.1 {31} MEASURE THIS DISTANCE Determine the minimum vertical position of the Wall Plate. Use the Look-up Table below to find the minimum distance between the mantel and the bottom of the Wall Plate {32}. This will be the intersectio ...

minimum distance from the mantel. Examples might be centering your TV between the mantel and the ceiling/crown molding, or to ensure extra space below the TV for pictures or a center speaker. To determine the precise vertical position of the Wall Plate (32}, use measurements already taken, then do some simple math using the formulas below. Gather measurements (write them down): (A) Required ...

CL CL STUD BEFORE AFTER A. Slide the Wall Plates sideways on the wall until they reach two studs. 2.6 CL B. If necessary, move Wall Plates to clear an outlet. If a Wall Plate installation is impeded by an electrical outlet (or other) and professionally relocating the outlet is impossible, try one of these options: • Move Wall Plates left or right to clear the outlet. The Lifting Arm can be ...

need to access: Move the Wall Plates {32} to the left or right of the desired position and temporarily install it. Use four Lag Bolts {17} to secure the Wall Plates to the studs. This will allow you to pull the Lifting Arm {35} down and install the Safety Bolt (see STEP 4.1) in order to access the blocked Wall Plate hole. Then, remove Lag Bolts and reinstall the mount in th ...

Attach the TV Brace to the Lifting Arm. Hang the TV Brace {33} onto the Lifting Arm {35} and make sure it’s level when tightening the four Leveling Screws {15}. 3.7 {33} {35} {15} 3.4 {17} {11} Do not over-tighten Lag Bolts, it can cause property damage or injury. Tighten only until the washers are firmly against the Wall Plate. WA R N I N G 3.5 Insert Cable Tie Anchors into Lifting Arm. ...

Mount 12 4.1 {20} Insert the Safety Bolt and Safety Nut. Use your body weight to firmly pull down the TV Brace {33} until the Lifting Arm {35} is horizontal to the floor. Continue holding onto the TV Brace. A second person must insert the Safety Bolt {20} through the Safety Hole in the base of the Lifting Arm and install the Safety Nut {27}. Slowly release the TV Brace until the Lifting Arm gently comes to rest against the Safety Bolt. ...

Customer Support 1.800.897.9755 x1 [email protected] {15} {15} {15} {33} {31} Center and level the TV on the TV Brace. Make sure the center of the brace is aligned with the center of the TV before leveling. Move on to STEP 4.4 once the TV is level. If the TV sags to one side, carefully slide it sideways in the opposite direction up to a MAXIMUM of 2 inches, until it levels. If the TV ...

First, review all the images in this step. With Safety Bolt {20} in place, use a 10–14mm socket wrench with an extension to adjust the Tension Bolt {41} (the long bolt inside the Lifting Arm {35}). For heavy TVs, turn the Tension Bolt clockwise in order to pull the Gas Springs {38} DOWN and increase the lifting force. Turn count ...

Adjust the Side Swivel Stop positions, if necessary. To keep your TV from bumping the mantel or wall, loosen the Locknuts {23} and adjust the Swivel Stop Screws to the desired stopping left and right positions. Tighten both Locknuts after the adjustments are made. If no swivel is desired, it may be necessary to remove the Locknuts and reattach them on the other side of the Swivel Bracket so th ...

MM340 Installation Instructions 16 For installation assistance, refer to the Troubleshooting Tips or contact Customer Support. 1.800.897.9755 ext.1 [email protected] Monday – Friday 7:00am – 4:00pm PST Verify the proper Lifting Performance (Force). MantelMount is designed to keep the TV securely in the UP position while also allowing it to gently rest in the DOWN position. Refer to diagram below. If you nee ...

CONTINUED ON NEXT PAGE T R O U B L E S H O O T I N G T I P S Customer Support 1.800.897.9755 x1 [email protected] T R O U B L E S H O O T I N G T I P S Customer satisfaction is our top priority! Following are solutions for the most common installation challenges. For further assistance, visit www.mantelmount.com/troubleshooting or contact Customer Support at 1-800-897-9755 ext.1 or s ...

18 CONTINUED FROM PREVIOUS PAGE TV is level in the UP position, but unleveled in the DOWN position. TV is level in the DOWN position, but unleveled in the UP position. MOUNT PERFORMANCE TV LEVELING ISSUE ISSUE SOLUTION (May require some trial and error to reach optimal performance.) POSSIBLE CAUSE HOW TO CHECK SOLUTION TV is tilting forward when in the UP position. This is generally an indication that the Lifting Force is no ...

* Limited Liftetime Warranty: MantelMount will replace or repair any product or part that proves defective due to improper workmanship or material during the warranty period. Go to https://www.mantelmount.com/pages/limited-lifetime-warranty for details. 26.0 11.2 29.5 19.0 Max. Clearance 15.0 Min. Clearance 27.0 Maximum Drop 5.5 Thickness 25.2 30°R 30°L MM340 SPECIFICATIONS U.S. Pat. No. 8, ...

mantelmount.com For missing/damaged parts or questions during installation, please contact our Customer Support team at 1.800.897.9755 ext.1 or [email protected]. Customer satisfaction is our highest priority! © 2019 MANEHU PRODUCT ALLIANCE, LLC REV P3082119 ...