M7 PA-111 Manual 

Text of the manual

1. The maximum recommended air pressure during operation must not exceed 90 psi

(6.3bar). Higher air pressure may create unsafe operating conditions for the tool and the user. 2. The compressed air should be cooled and have a water filter installed at the outlet end of the compressor. Even with a water filter installed, some water may still condense in the

Ideal system connection:

Piping diameters and length requirement: The diameter ΦA required for the inlet pipe is recommended on the specification table. The diameter ΦB required for the branch pipe (from to ) should be 2 times as large as ΦA. ΦB = 2 x ΦA The diameter ΦC required for the primary air supply (from to ) should b

1. This tool should only be used as a hand operated tool. It is powered by compressed air and is not

insulated against electric shock. 2. This tool is specially designed for riveting sheet metals together. Any application or use of this tool other than what it is designed for is strictly prohibited. 3. High sound levels may cause hearing damage. Always wea

1. Disassemble and clean all the components inside the front housing with pressured air.

2. Take the piston assembly apart from the air cylinder, clean and apply some pneumatic oil to both piston and cylinder walls. 3. Rehabilitate the tool by assembling everything back reversely. 4. Refer to the supplied parts list to perform the proper maintenance proces

Procedure to change the Jaw Housing Assembly:

Step1: Use Multi-Wrench (B) / PA-201P55 to remove the Front Housing / PA-201P02. Step2: Hold still the Jaw Housing Coupler / PA- 201P07 with the supplied Multi-Wrench (B) / PA- 201P55 and disassemble the Jaw Housing / PA- 201P03 with the Multi-Wrench (A) / PA-201P54. Step3: Reverse the procedure to assemble a

Lire ce guide avant toute installation, opération,

maintenance ou réparation. 1.La pression d'air maximal recommandé ne devrait jamais excéder les 90 psi (6,3bar). Une utilisation à une pression d'air supérieur peut causer des dommages à l'outil et/ ou pour son utilisateur. 2.L'air à la sorti du compresseur devrait être refroidi et passer à trave

1. Tout l'outillage pneumatique devrait être opéré de façon manuelle. Ils sont alimentés par de l'air

comprimé et ne sont pas conçus pour être utilisés dans des milieux sous tension électrique. 2. Cet outil est conçu spécifiquement pour le rivetage de feuille de métal ensemble. Toute autre utilisation de cet outil est fortement

1. Désassembler et nettoyer toutes les composantes à l’intérieur de la cloche avant REMOVE

à l’aide d’une décharge d’air. 2. Détacher et nettoyer le piston et le cylindre hydraulique. Appliquer de l’huile pneumatique sur le piston et sur les parois internes du cylindre. 3. Reconditionner l’outil en remettant les pièces démo

Procédure pour changer les buses:

Etape 1: Utiliser la clé multi-fonction “A” PA-201P55 pour retirer la cloche frontale PA-201P02. Etape 2: Rattacher le raccord de la buse PA-201P07 avec la clé multi-fonction PA-201P55 et désassembler la buse PA-201P03 avec la clé multi-fonction “A” PA-201P54. Etape 3: Réassembler l’ensemble des pièces e

1. Es ist strikt verboten, die Druckluftschlagschrauber in einem explosionsgefährdeten

Arbeitsumfeld zu benutzen. 2. Es ist ratsam, das Werkzeug auf einer festen Arbeitsfläche zu verwenden, z. B. auf einem festen und ebenen Arbeitsplatz. 3. Beachten Sie, dass die Arbeitsumgebung mit dem Druckluftwerkzeug immer gut belüftet sein soll. 4. Vor der Benutz

Other Rivet Tools Manuals