ACP RMS510TS2 Technical Information
Text of ACP RMS510TS2 Technical Information
ACP RMS510TS2 Commercial Microwave—Technical Information
230V, 50 Hz Models
RMS510TS2 P2006703M
RMS510DS2 P2006704M
RMS510TSUA P2006707M
RMS510DSUA P2006708M
RMS510TSCA P2006709M
RMS510TSIA P2006710M
RMS510TSAA P2006711M
Due to possibility of personal injury or property damage, always contact an authorized technician for servicing or
repair of this unit.
Refer to Owner’s Manual for installation and operating instructions
July 2019
1
©2019 ACP, Inc
©2019 ACP, Inc.
2
16500066
Component Testing Procedures
Illustration
Component
Test
Results
Thermal Cutout
Disconnect all wires from TCO.
Measure resistance across terminals.
Cavity TCO………… ......................................
Magnetron TCO ..............................................
Open at 203° F (95° C) Closes at 185°
F (85° C)
Open at 293° F (145° C) Closes at 275°
F (135° C)
Diode/Rectifier
Discharge Capacitor
Remove d
©2019 ACP, Inc. 3
16500066
Component Testing Procedures
Illustration
Component
Test
Results
Transformer
HV Fuse
(Terminal 4)
Discharge Capacitors
Remove all wires from terminals.
Measure resistance from:
Terminal 1 to Terminal 2..................................
Wire 5 to Wire 6 ...............................................
Terminal 4 to Ground screw on transformer...
Terminal 4 to any other terminal ......................
Resistance
2.0 Ω.
©2019 ACP, Inc. 4
16500066
Power Output Wattage Testing Procedure
All Amana and Menumaster microwave oven power outputs are rated using the IEC705 standards. Using the
IEC705 test method requires precision measurements and equipment that is not practical to be performed in the
field. Using the test shown below will indicate if the oven performance is satisfactory.
Test equipment required:
1000 ml test container and thermometer.
Digital w
©2019 ACP, Inc. 5
16500066
Wiring and Schematic Diagrams
To avoid risk of electrical shock, personal injury or death, disconnect power to oven and discharge capacitor
before servicing, unless testing requires power.
©2019 ACP, Inc. 6
16500066
Electronic Control Operation
So…how do I use it?
(A)
( B)
(C)
(D)
(E)
(F)
(G)
Note: Control panel coloring may vary by
model
Control Panel Features
(A) LED DISPLAY
(B) TIME ENTRY KEY
(C) X2 KEY
(D) POWER LEVEL KEYS
(E) NUMBER KEYS /
PRESET PROGRAM KEYS
(F)
STOP/RESET KEY
(G) START KEY
Interrupting Operation (Pause Mode)
While the oven is operating, press STOP/RESET key
to interrupt operation
©2019 ACP, Inc. 7
16500066
Electronic Control Operation
Programming Mode
This mode allows the user to assign cook times, power levels, and stage cooking to
the Number Keys.
1.
Open oven door and press and hold Number Key “1” for 5 seconds. The oven
beeps and LED displays “ProG”.
Note: If STOP/RESET key
is pressed before programming is
complete,changes are discarded and microwave exits programming mode.
2.
Press a Number Key to change
©2019 ACP, Inc. 8
16500066
Electronic Control Operation
On-the-Fly Cooking
On-the-Fly Cooking allows the user to start another cook cycle while the oven is
operating or paused.
Note: User Option OP:51 must be enabled for use of On-the-Fly cooking.
1.
While the oven is cooking or while in Pause Mode, press a Number Key to
automatically start the Preset Program associated with that key.
2.
Oven begins cooking and the LED displays cooking time.
3.