AMP Research PowerStep 77132-01A Installation Manual

I N S T A L L A T I O N G U I D E 3-5 Hours Professional installation recommended Invented, engineered and manufactured exclusively by AMP Research in the USA. May be covered by one of the following patents: 6,641,158; 6,830,257; 6,834,875; 6,938,909; 7,055,839; 7,380,807; 7,398,985; 7,584,975 ©2012 ...

A M P R E S E A R C H P O W E R S T E P T M – J e e p W r a n g l e r J L A A B B 2 2 1 1 WEIGHT: jeep jk PSXL die cast linkage assembly PROPRIETARY AND CONFIDENTIAL THE INFORMATION CONTAINED IN THIS DRAWING IS THE SOLE PROPERTY OF . ANY REPRODUCTION IN PART OR AS A WHOLE WITHOUT THE WRITTE ...

A M P R E S E A R C H P O W E R S T E P T M – J e e p W r a n g l e r J L (A) End cap left (x1) 1 x2 Running board assembly D B (B) End cap right (x1) (C) T-nut insert (x2) (D) Socket cap screw (x2) (E) End cap wedge right (x1) (F) End cap wedge left (x1) A C E F Cut Dimension 4 Motor Linkage assemb ...

A M P R E S E A R C H P O W E R S T E P T M – J e e p W r a n g l e r J L Socket Cap Screw 13 x8 Cable tie (11”) 21 x2 Cable tie (7”) 20 x20 23 LED Lamp x4 12 x4 5/16 Flange Bolt 10 M8 Button Head Bolt x10 22 Butt Connector x11 11 x4 M6 Flange Bolt Upper Mount Spacer 19 x4 5/16-18 Carriage Bolt 14 ...

A M P R E S E A R C H P O W E R S T E P T M – J e e p W r a n g l e r J L 26 LED Light Bracket x4 Shim Spacer 27 x2 Linkage mounting Bracket (Driver Side) 33 x2 28 Rail Support Bracket x2 Linkage mounting Bracket (Passenger Side) 34 x2 31 Motor Cover x2 29 CRH Motor x2 30 Cinch Fastener x6 32 M8 Head Hex ...

A M P R E S E A R C H P O W E R S T E P T M – J e e p W r a n g l e r J L Assemble brackets onto vehicle. Use provided button head bolts (10) and washers (18) at pinch weld with captive washer nuts (17) at pinch weld. Assemble hardware loosely. Next use provided captive washer bolts (15) to attach bracket ...

A M P R E S E A R C H P O W E R S T E P T M – J e e p W r a n g l e r J L Mount front drive linkage onto driver side. Thread supplied bolts (15) into front drive linkage. Repeat step for Rear idler linkage. Do not tighten. Install provided spacer (19) and M6 bolt (11) into upper mount as shown on both the ...

A M P R E S E A R C H P O W E R S T E P T M – J e e p W r a n g l e r J L Prepare large tie-wraps for mounting Power Step Controller. Loosely loop tie-wraps around large bundle of wires behind battery in engine compartment. Insert controller into tie-wrap loops and cinch down securely. The tie-wraps shou ...

A M P R E S E A R C H P O W E R S T E P T M – J e e p W r a n g l e r J L Remove sill plate cover. Remove grommet under floor and route trigger wires and power wire thru grommet. Mount door trigger module to wire harness in kick panel area. Using a 10mm socket remove ground lug and connect ground to body. ...

A M P R E S E A R C H P O W E R S T E P T M – J e e p W r a n g l e r J L Affix LED light XD bracket on rail. Slide bracket into desired position and tighten using 5/32” Allen key. Using supplied butt connectors, connect the lamp wires. Red to Red, Black to Black. Once Crimped use heat gun to shrink tu ...