Avalue Technology ECM-BT45 Operation & User’s Manual

12 ECM-BT45 User’s Manual COM 2 x RS232 (Pin header) Com1 of the RS232 above must have Pin 9 selectable by jumper (5V, 12V, RI) to enable power to serial touch Others 4 * USB 2.0 on 2 * 2mm 2 x 5 pin headers (same as ECM-CX700) Rear I/O Connectors USB 1 x USB3.0, 1 x USB 2.0 LAN 4 x Ethernet HDMI 1 x HDMI LED Front Panel LED Connector (for system use) Require same as ECM_CX700 LED indicators -LED for Power -LED for SATA access Mechanical & Environmental Power Requirement +12V power input (the same as ECM-CX700) ACPI Single power ATX Support S0,S3, S4, S5 ACPI 3.0 Com ...

ECM-BT45 User’s Manual 59 4.2 Install MBI Driver Insert the Supporting DVD-ROM to DVD-ROM drive, and it should show the index page of Avalue’s products automatically. If not, locate Index.htm and choose the product from the menu left. Note: The installation procedures and screen shots in this section are based on Windows 8.1 operation system. If the warning message appears while the installation process, click Continue to go on. Step 3. Click Next to proceed setup. Step1. Click Next to start installation. Step 4. Click Finish to complete setup. Step 2. Click Yes to ...

30 ECM-BT45 User’s Manual 3.1 Introduction The BIOS setup program allows users to modify the basic system configuration. In this following chapter will describe how to access the BIOS setup program and the configuration options that may be changed. 3.2 Starting Setup The AMI BIOS™ is immediately activated when you first power on the computer. The BIOS reads the system information contained in the NVRAM and begins the process of checking out the system and configuring it. When it finishes, the BIOS will seek an operating system on one of the disks and then launch an ...

ECM-BT45 User’s Manual 51 Item Option Description High Precision Timer Disabled Enabled[Default] Enable or Disable the High Precision Event Timer. 3.6.3.2.1 Azalia HD Audio Item Option Description Audio Controller Enabled[Default], Disabled Control Detection of the Azalia device. Disabled = Azalia will be unconditionally disabled. Enabled = Azalia will be unconditionally Enabled. Auto = Azalia will be enabled if present disabled otherwise. HDMI Port B Enabled[Default], Disabled Enable/Disable HDMI Port B. ...

ECM-BT45 User’s Manual 23 2.3.11 Serial port 1 connector (JCOM1) Signal PIN PIN Signal NDCDA# 1 2 NRXDA NTXDA 3 4 NDTRA# GND 5 6 NDSRA# NRTSA# 7 8 NCTSA# NRIA# 9 10 NRIA# 2.3.12 Serial port 2 connector (JCOM2) Signal PIN PIN Signal NDCDB# 1 2 NRXDB NTXDB 3 4 NDTRB# GND 5 6 NDSRB# NRTSB# 7 8 NCTSB# NRIB# 9 10 NC ...

54 ECM-BT45 User’s Manual 3.6.4.1 Secure Boot menu Item Option Description Secure Boot Disabled[Default] Enabled Secure Boot can be enabled if 1. System running in User mode with enrolled Platform Key(PK) 2. CSM function is disabled. Secure Boot Mode Standard Custom[Default] Secure Boot mode selector. ‘Custom’ Mode enableds users to change Image Execution policy and manage Secure Boot Keys. ...

16 ECM-BT45 User’s Manual 2.2 Jumper and Connector List You can configure your board to match the needs of your application by setting jumpers. A jumper is the simplest kind of electric switch. It consists of two metal pins and a small metal clip (often protected by a plastic cover) that slides over the pins to connect them. To “close” a jumper you connect the pins with the clip. To “open” a jumper you remove the clip. Sometimes a jumper will have three pins, labeled 1, 2, and 3. In this case, you would connect either two pins. The jumper settings are schemat ...

10 ECM-BT45 User’s Manual 1.4 Manual Objectives This manual describes in detail the Avalue Technology ECM-BT45 Single Board. We have tried to include as much information as possible but we have not duplicated information that is provided in the standard IBM Technical References, unless it proved to be necessary to aid in the understanding of this board. We strongly recommend that you study this manual carefully before attempting to interface with ECM-BT45 series or change the standard configurations. Whilst all the necessary information is available in this manual we ...