Text of APART Champ-2 Manual
SGL led CH1
= red
TEMP led CH1
= red
SGL led CH2
= red
TEMP led CH2
= red
What to do ?
Output signal
condition
Ch 1 amp
overheat
Yes
Reduce input
signal or check
amplifier load.
Wait for cool
down.
No output
Ch 2 amp
overheat
Yes
Reduce input
signal or check
amplifier load.
Wait for cool
down.
No output
Ch 1 amp
error ( ...
What is APC ?
APART Champ-2 APC is one of the most intelligent amplifier protection circuits ever designed, simply
because it does the job without interfering with the typical dynamic character of
music. APC allows you to fully exploit the potential of the amplifier, maintaining high
power reserves and thus producing high, clean power.
It is a common ...
Champ-2 can be mounted in a 19” rack, taking up only 1 rack space. Always allow a good airflow
APART Champ-2 around the amplifier’s front, rear, side, top and bottom. When installing in a rack with multiple audio
devices, it is compulsory to leave one rack space between units. Fill the empty rack spaces with
meshed blind panels for improved vent ...
Audiophile grade components mounted on solid aluminum and steel construction chassis for
APART Champ-2 •
the highest possible signal integrity and reliability, even under difficult circumstances.
High current, high voltage discrete output stage in class G configuration, capable of driving
•
even the most demanding speaker systems and combinatio ...
APC circuitry constantly analyses incoming music signals and keeps dynamics
alive. An additional ultra fast peak limiter avoids amplifier clipping in case someone hits the
inputs too hard. Please remember, this is a musical amplifier, please leave some headroom
and enjoy the music.
Bridge or stereo mode: more than dou ...
Dynamic program power, both channels driven
APART Champ-2 Bridge-mono operation 8 ohm
750 W
2 channel mode 8 ohm
200 W / ch
2 channel mode 4 ohm
350 W / ch
2 channel mode 2.7 ohm
450 W / ch
Dynamic capacity at 2 ohm, both channels
driven
600 W / ch
6. Technical specifications
Rated output power, both channels driven:
Bridge-mono operation 8 ohm
350 ...
1) Channel 2 unbalanced input on cinch connectors: use the top or bottom cinch connector to
APART Champ-2 apply an unbalanced signal on channel 2. These connectors are wired in parallel, this means
you can use the second connector as a signal link connector.
2) Channel 2 balanced input on Neutrik XLR connector, this connector is wired in paralle ...
It is possible to integrate Champ-2 in a high quality audio chain. In order to adapt the front panel
APART Champ-2 dimensions to the dimensions of other equipment, it is possible to remove the 19” brackets and
handles for an even more sleek and refined look.
Remove the two screws marked in red circles and slide off the handles.
5. Standalone use
...
Why does live music leave an unforgettable impression on you ? The answer is simple: dynamics.
APART Champ-2 The ability of a sound system to produce crystal clear low level sounds as well as extreme
musical peaks without any distortion, the power to leave some headroom for those occasional
peaks in music. Pure power ! This ease of mu ...
Caution: hot and sharp surfaces ! This professional device needs to be installed by
qualified personnel only.
Please check the carton box for any kind of damage on reception of the goods. In case of a
•
damaged carton, please contact your dealer before opening the carton.
!!!! Danger !!!! Exposure to extremely high noise level ...
qualified personnel only.
Please check the carton box for any kind of damage on reception of the goods. In case of a
•
damaged carton, please contact your dealer before opening the carton.
!!!! Danger !!!! Exposure to extremely high noise levels may cause a permanent hearing
•
loss. Individuals vary considerably to noise induced hearing los
The ability of a sound system to produce crystal clear low level sounds as well as extreme
musical peaks without any distortion, the power to leave some headroom for those occasional
peaks in music. Pure power ! This ease of music reproduction can not be described in figures or
specifications.
In the following pages we will e
•
the highest possible signal integrity and reliability, even under difficult circumstances.
High current, high voltage discrete output stage in class G configuration, capable of driving
•
even the most demanding speaker systems and combinations. Either at low or high power, you
will hear the Champ-2 difference.
Custom designed side mount h
alive. An additional ultra fast peak limiter avoids amplifier clipping in case someone hits the
inputs too hard. Please remember, this is a musical amplifier, please leave some headroom
and enjoy the music.
Bridge or stereo mode: more than double the output power and convert this amplifier into a
•
monoblock amplifier with one push on a bu
APC is one of the most intelligent amplifier protection circuits ever designed, simply
because it does the job without interfering with the typical dynamic character of
music. APC allows you to fully exploit the potential of the amplifier, maintaining high
power reserves and thus producing high, clean power.
It is a common misunderstanding that high power amplifiers will overload or destroy
lower power speakers, the oppo
been switched to bridge mode, this potmeter sets the level for bridge operation.
2) Signal led channel 1: this led lights up green when a sufficiently strong signal is present on the
left channel, after passing the input level control. At startup, the led will light up red during a
few seconds, this is perfectly normal. When it lights
on the left channel, after passing the input level control. At startup, the led will light up red
during a few seconds, this is perfectly normal. When it lights up red during use, the power
transformer or power amplifier is overheated or in protect mode and is shut down. Turn off the
power. The amplifier will not turn on automatically afte
= red
TEMP led CH1
= red
SGL led CH2
= red
TEMP led CH2
= red
What to do ?
Output signal
condition
Ch 1 amp
overheat
Yes
Reduce input
signal or check
amplifier load.
Wait for cool
down.
No output
Ch 2 amp
overheat
Yes
Reduce input
signal or check
amplifier load.
Wait for cool
down.
No output
Ch 1 amp
error (DC,
HF, short
circuit,
overload)
Yes
Switch off power
and remove
error. Leave
switched off
for at le
apply an unbalanced signal on channel 2. These connectors are wired in parallel, this means
you can use the second connector as a signal link connector.
2) Channel 2 balanced input on Neutrik XLR connector, this connector is wired in parallel to
connector ‘3’. This allows you to link the balanced signal to another amplifier.
3) Chann
this case you can apply an input signal to the channel 1 input only ! Leave the channel 2
connectors open ! Bridge mode input level is controlled by the channel 1 volume controller
only. The ‘BR’ led on the front panel will indicate that the amplifier is in bridge mode. Minimum
bridge mode speaker load is 8 ohms. Never use the s
around the amplifier’s front, rear, side, top and bottom. When installing in a rack with multiple audio
devices, it is compulsory to leave one rack space between units. Fill the empty rack spaces with
meshed blind panels for improved ventilation. Never mount the amplifier in a sealed cabinet, unless
adequate forced ventilation is provid
dimensions to the dimensions of other equipment, it is possible to remove the 19” brackets and
handles for an even more sleek and refined look.
Remove the two screws marked in red circles and slide off the handles.
5. Standalone use
Bridge-mono operation 8 ohm
750 W
2 channel mode 8 ohm
200 W / ch
2 channel mode 4 ohm
350 W / ch
2 channel mode 2.7 ohm
450 W / ch
Dynamic capacity at 2 ohm, both channels
driven
600 W / ch
6. Technical specifications
Rated output power, both channels driven:
Bridge-mono operation 8 ohm
350 W
2 channel mode 8 ohm
120 W / ch
2 channel mode 4 ohm
180 W / ch
2 channel mode 2.7 ohm
200 W / ch
(RCA) / 4 ohm
10 Kohm / 1 V 0dBV
Input impedance / sensitivity balanced (XLR)
/ 4 ohm
20 Kohm / 1 V 0 dBV
Frequency response (0, -0.5 dB)
10 Hz – 50 kHz
THD
< 0.05 %
IMD
< 0.06 %
Noise
>100 DBA
Gain
30 dB (36 dB bridged)
Damping factor
> 200
Dynamics and level control
APC, switchable for 2-3 or 4-8 ohms
Power amp circuit design
High current, high voltage class G
Efficiency (dynamic program
Send your ideas or suggestions to
[email protected]
CHAMP-2 is developed by
Audioprof nv
Lanteernhofstraat 90
BE-2100 Deurne
BELGIUM
Company names, product names, and names of formats etc. are the trademarks or registered trademarks of
their respective owners.
© 2008 APart-Audio specifications subject to change without notice.