Autophix 7910 Operation & User’s Manual

scan tool, Read this instruction manual first and observe the following safety precautions at a minimum whenever working on a vehicle: Always perform automotive testing in a safe environment Do not attempt to operate or observe the tool while driving a vehicle. Operating or observing the tool will cause driver distraction and could cause a fatal accident. Wear safety eye protection that meets ANSI standards. Operate the vehicle in a well ventilated work area: Exhaust gases are Poisonous. Put the transmission in PARK (for automatic transmission) or NEUTRAL (for ma ...

1. LCD DISPLAY – Indicates test results. Backlit, 320 x 240 pixels display 2. [OK] BUTTON – Confirms a selection (or action) from a menu. 3. ESC BUTTON – Cancels a selection (or action) from a menu or returns to the menu. OBDII For bmw Oil reset BMS reset BAT EPB reset Tool Setup ETCS reset 2 1 3 6 5 7 2 4 10 9 ...

4. [LEFT ]SCROLL BUTTON –in the menu mode through the menu and sub menu move to the left, when rolling in a data interface, use the left button can be moved to the last screen. 5. [RIGHT] SCROLL BUTTON –In the menu mode through the menu and sub menu item move to the right, when rolling in the data interface, use the right button can be moved to the next screen. 6. [UP] SCROLL BUTTON –in the menu mode through the menu and sub menu item moving up. When retrieving data for more than a screen by moving up the screen to the previous screen for more data. 7. [DOWN] SCROLL BUTTO ...

[G38(2017-Present)] ，it displays as follow: 1.1 Turn the ignition on. 1.2 Locate the vehicle's 16-pin Data Link Connector (DLC). 2.1 For bmw 1. Connect 7910 2. 7910 Features Choose [For bmw] and then select [For BMW Series Diagnose]. The screen will show all car series. As follows: Select Brand Last Test Shortcut For BMW Series Diagnose For MINI Series Diagnose For Rolls-Royce Series Diagnose Select System Diagnose 2/5 Select Chassis F90(2017-Present) G30/G31(2017-Present) G38(2017-Present) 10/10 Select Series For 1 Series For 2 Series For 3 Series For 4 Series For 5 Series For 6 ...

2.2 Basic Functions Select System Diagnose CAS Car Access System ECM Engine Control Module ECM2 Engone Control Module 2 EGS Transmission ABS/ACS/DSC Dynamic Stabilit... SRS Air Bag FPB Electronic Parking Brake 1/86 Select Menu System Scan Manual Select 2/2 Select Function Basic Functions Special Functions Erase All Systems Fault Codes 1/3 System scan is to scan all vehicle systems. Manual Select is to display all possible systems, select one of the systems to diagnosis. Choose [Manual Select] and it displays as follows: For example: Choose [ECM Engine Control Module] and it displays as follows: Select ...

Select Function Version Information Read Fault Codes Erase Fault Codes Read Datastream 1/4 Select Function Version Information Read Fault Codes Erase Fault Codes Read Datastream 2/4 Select Function Version Information Read Fault Codes Erase Fault Codes Read Datastream 3/4 Choose [Version Information] and it displays as follows： Version Information Diagnosis Index: 0F2426 2.2.2 Read Fault Codes Choose [Read Fault Codes]. Press up or down button to check each fault code as follows: Read Fault Codes 29CF Combustion misfires Cylinder 3 1/20 2.2.3 Erase Fault Codes Choose [Erase Fault Codes] then press [OK] button as follows: Inf ...

Erase Fault Codes Read Datastream 4/4 Select Function View All Items Select Items 2/2 Select Datastream All Datastream Of Page [v] [v] [v] [v] [v] Engine speed[rpm] DISA potentiometer voltage[v] Throttle opening[%] Throttle opening[%] 1~4/6 Choose [Read Datastream] then press [OK] button as follow: Choose [Select Items] and press [OK] button as follows: Press [LEFT] and [RIGHT] buttons to page Press [UP] and [DOWN] buttons to select one by one Press [OK] button to select the Datastream Press [ESC] button to read Datastream You need to press [OK] again to clear the fault codes. Or you can press [ESC] ...

2/3 Select Function CBS Function(Service Function) Reset Control Unit ECM Engine Control Module Electric fuel pump Battery Management EPB Electronic Parking Brake Steering-angle Sensor 1/9 CBS Function(Service Function) Oil reset CBS Reset CBS Correction 1/3 Oil reset This function will perform’ engine oil reset’ and ‘vehicle check reset’. Note! The vehicle check is related to the engine oil. After the oil is Choose [Special Functions] and it displays as follows: 2.3 Special Functions Choose [CBS Function (Service Function)] and it displays as fo ...

Reset Control Unit ECM Engine Control Module Electric fuel pump Battery Management EPB Electronic Parking Brake Steering-angle Sensor 3/9 ECM Engine Control Module Reset adaptation values Idle speed Learning Valvtronic limit positi... 1/3 Choose [ECM Engine Control Module] and it displays as follows: 2.3.2 ECM Engine Control Module Select Function CBS Function(Service Function) Reset Control Unit ECM Engine Control Module Electric fuel pump Battery Management EPB Electronic Parking Brake Steering-angle Sensor 5/9 Choose [Battery Management] and it displays as follows: Step 1: Use the up or down button to s ...

press the [OK] button to display the following menu: Special Functions The battery replacement is entered in the engine electronics(DME or DDE) Please wait! 10 Choose [EPB Electronic Parking brake] and it displays as follows: 2.3.4 EPB Electronic Parking Brake Select Function CBS Function(Service Function) Reset Control Unit ECM Engine Control Module Electric fuel pump Battery Management EPB Electronic Parking Brake Steering-angle Sensor 6/9 EPB Parking brake Workshop mode,Automatic Hol... Startup-up,Automatic Hold br ake 1/2 Choose [Steering-angle sensor] and it displays as follows: ...

3/3 Note: The special features of each model are different, please according to the actual operation. Note: For BMW car after 2003. Choose [Erase All Systems Fault Codes] and it displays as follows: You need to press [OK] again to clear the fault codes. Or you can press [ESC] button to give up clearing fault codes. It shows as the follow after clearing the fault codes. 2.4 Erase All Systems Fault Codes Information Erase fault codes! Are you sure? Information Erase fault codes had success. Please wait 10 seconds, Turn ignition off and Switch on again. Read fault codes to ver ...

Vehicle Information 1/6 1) Use the UP/DOWN scroll button to select Read Codes from the Diagnostic Menu and press [OK]. If there are no Diagnostic Trouble Codes, the display indicates "No (pending) codes are stored in the module!" Wait a few seconds or press any key to return to the Diagnostic Menu. Pending Codes will not turn on the malfunction indicator light, and codes will be cleared from memory if there is no failure during the following warm-up period. 3.1 Read Codes 3. OBDII System Stored codes are also known as "hard codes" or "permanent codes". These codes cause t ...

The control module number, sequence of the DTCs, total number of codes detected and type of codes (Generic of Manufacturer specific) will be observed on the upper right hand corner of the display. Notes: This function is performed with key on engine off. Do not start the engine. Before performing this function, make sure to retrieve and record the trouble codes. After clear- ing, you should retrieve trouble codes once more or turn ignition on and retrieve codes again. If there is still some trouble codes for hard troubles, please find the reason caused the trouble code firstly, and then solve the problem. N ...

Vehicle Information 2/6 1) Use the UP/DOWN scroll buttons to select Erase Codes from the Diagnostic Menu and press [OK]. 2) A warning message comes up asking for your confirmation. 3) Press [OK] to confirm. Erase Codes Clear/Reset Emission-Related Diagnostic Information, AreYou sure? Erase Codes Please Turn Ignition ON with Engine Off, Press OK key to continue! Erase Codes Emission-Related Diagnostic Information has been cleared! 14 ...

Vehicle Information 3/6 I/M Readiness Since DTCs Were Cleared This Drive Cycle 1/2 Diagnostic Menu Read Codes Erase Codes I/M Readiness Data Stream Evap System Test Vehicle Information 4/6 Datastream View All Items Select Items 1/2 I/M refers to Inspection and Maintenance, that is legislated by the Government to meet federal clean-air standards. I/M Readiness indicates whether or not the various emissions-relat- ed systems on the vehicle are operating properly and are ready for Inspection and Maintenance testing. The I/M readiness Monitor Status function also can be used ...

Evaportive system leak test not supported Diagnostic Menu Read Codes Erase Codes I/M Readiness Data Stream Evap System Test Vehicle Information 5/6 Vehice Information Diagnostic Menu Read Codes Erase Codes I/M Readiness Data Stream Evap System Test Vehicle Information 6/6 This function enables the conditions required to conduct an evaporative system leak test, but does not actually run the test. The vehicle manufacturer is responsible to determine the criteria to automatically stop the test. Before performing this function, please check the vehicle's service repair manual to determine the necessary procedures. Select [Vehicle Inf ...

Unit of Measure Skin Style Feedback Device Information 1/7 Language English Svenska Suomalainen Norsk språk Dansk Deutsch Français 1/10 Choose [Language] and it displays as follows: 4. Tool Setup 4.1 Language Tool Setup Language Beeper Instructions(Display at startup) Unit of Measure Skin Style Feedback Device Information 2/7 Beeper OFF ON 1/2 Choose [Beeper] and it displays as follows: 4.2 Beeper Choose [Instructions(Display at startup)] and it displays as follows: 4.3 Instructions(Display at startup) 17 ...

Unit of Measure Skin Style Feedback Device Information 3/7 Instructions(Display at startup) OFF ON 1/2 Tool Setup Language Beeper Instructions(Display at startup) Unit of Measure Skin Style Feedback Device Information 4/7 Unit of measure Mertic Imperial 1/2 Choose Unit of measure and it displays as follows: 4.4 Unit of measure 18 Tool Setup Language Beeper Instructions(Display at startup) Unit of Measure Skin Style Feedback Device Information 5/7 Skin Style Sky Gray Gem Blue 1/2 Choose Unit of measure and it displays as follows: 4.5 Skin Style ...

Unit of Measure Skin Style Feedback Device Information 6/7 1. If it shows connected error with vehicle or other problem during using, please using the feedback function. Choose [Feedback] and it displays as follows: Next : Press EXIT Button several times and return to the main menu. 2. For example: Register battery change fail Enter [Register battery change] option, and do Register battery change again (This step is very important) Note : Keep tool connect with car in above steps. 3. After doing register battery change, disconnect with car. 4.6 Feedback Feedback Automatic recording is ...