Autonics TZN Series Manual 

※1: Only for TZ4SP, TZ4ST, TZ4L, TZN4M Series. Features Ordering information ● Dual PID auto tuning function: High-speed response of PID control to reach to the desired value fast, low-speed of response of PID control to minimize the overshoot even though response is a little bit slow. ● High display accuracy: ±0.3%(by F.S. value of each input) ● 2-Steps auto tuning control function ● Multi-input function (13 kinds of multi-input selection function): Temperature sensor, voltage and current selection function. ● Various sub output function: Includes in LBA, SBA, 7kinds of alarm o ...

※1. AC/DC power type is only for TZ4SP, TZ4ST, TZN4M, TZ4L Series. ※Environment resistance is rated at no freezing or condensation. Specifications Series TZ4SP TZN4S TZ4ST T ...

※In case of Analog input, please use T.C(Thermocouple) terminal and be careful about polarity. TZN4S TZN4M TZ4SP TZ4ST TZ4M Connections EV-1 OUT 250VAC 1A 1a SV2 IN Max.5VDC 250㎂ MAIN OUT 250VAC 3A 1c Resistive load SOURCE 100-240VAC 50/60Hz 6VA 24VAC 50/60Hz 8VA 24-48VDC 7W H C L B' RTD T.C SENSOR B A 5 2 10 9 8 1 11 4 3 7 6 MAIN OUT SSR Current 12VDC ±3V 30mA Max. DC4-20mA Load 600Ω Max. 9 9 10 10 mA V MAIN OUT SSR Current 12VDC ±3V 30mA Max. DC4-20mA Load 600Ω Max. 12 13 mA V 12 13 SV2 IN Max.5VDC 250㎂ MAIN OUT 2 ...

Dimensions ● Panel cut-out TZN4S TZN4M TZ4L / TZN4L TZ4H / TZN4H TZ4W/TZN4W (unit: mm) 48 10 90 61 44.8 Min. 55 Min. 62 45 +0.6 0 45 +0.6 0 84 72 10 73 67 Min. 91 M ...

48 61 15 12 80 44.8 Min. 55 Min. 62 45 +0.6 0 46 +0.6 0 Min. 74 Min. 90 68 +0.7 0 68 +0.7 0 12 95 44.8 48 61 72 86 100 13 68 ● Panel cut-out ● Panel cut-out TZ4H TZN4H 48 96 108 48 96 108 90 13 90 Min. 50 Min. 112 45 +0.6 0 92 +0.8 0 ● Panel cut-out TZ4W TZN4W 108 96 48 108 96 48 100 13 44.8 Min. 112 Min. 50 92 +0.8 0 45 +0.6 0 ● Panel cut-out (unit: mm) ...

1: Display Processing value(PV) (Red) 5: Mode key 9: Indicate EVENT 1 output 2: Display Setting value(SV) (Green) 6: Autotuning operation key 10: Indicate EVENT 2 output 3: Indic ...

Set range: Within the rated using range of each sensor. Set alarm temperature in EV-1. Set range: Within the rated using range of each sensor. Set alarm temperature in EV-2. Set range: Within the rated using range of each sensor. If press MD key for 3sec., it will go to parameter 1 group. Set monitoring time of loop break alarm. Set range: 0 to 999 sec. Set interval between ON and OFF for alarm output. Set range: 1 to 100℃ (0.1 to 100.0℃) ※It is only displayed for temperature alarm output. Set proportional band. / Set range: 0.0 to 100.0%. ※If setting value P as 0.0, it will be ON/OFF control. S ...

Parameter 2 group Parameter Factory default Parameter Factory default Parameter Factory default Parameter Factory default IN-T KCaH AL-T AL-A PIDT PIdS H-SC 1300 EU-1 AL-1 AtT T ...

B) In case of voltage input : 1-5VDC, 0-10VDC C) In case of current input : DC4-20mA SW1 SW1 SW1 SW2 SW2 SW2 SW1:1 SW1:2 SW1:2 SW2: V SW2: V SW2: mA 1 1 2 2 2 2 V V V mA mA mA Input type and range Input type switch ※Factory default of input type switch: Temperature sensor input. ※Please select B) or C) according to input specification when it is voltage or current. Input type Display Input range(℃) Input range(℉) Thermocouple K(CA) H KCaH -100 to 1300℃ -148 to 2372℉ K(CA) L KCaL -100.0 to 999.9℃ This mode cannot ...

This unit has output for control and sub(alarm) output. Sub output is optional. (This alarm output is relay contact(1a) and operates regardless of output for control.) Alarm outp ...

Auto tuning time Time(t) SV ℃ (tun 2 mode) Auto tuning time 70% of SV Time(t) SV ℃ Functions Auto tuning [ AtT] Sensor Break Alarm [ SBA] Sub output [ EU-1, EU-2] Error Loop Break Alarm [ LBA] PID auto tuning function automatically measures the thermal characteristics and response of the control system and then executes its value under high response & stability after calculating the time constant of PID required to control optimum temperature. ● ●Execute the auto tuning function at initial time after connecting the controller & the sensor. ● ●Execution of auto tuning is started when pressing AT key for ...

Setting value (SV) Decrease reset Increase reset Normal deviation Normal deviation Process value(PV) (Fig. 1) SV S PV t PIdF ※ t : Reaching time S : Overshoot SV: ...

ramp function is not used Control temperature when ramp function is used RAPU setting time RAPU setting time tu tu Initial SV Changing SV Cool / Heat function [ O-FT] SV2 function [ SU-2] If using SV2 function, it changes the temperature of control system to the second setting value by external relay contact signal. It can change the setting value as sequentially by relay contact without key operation. ● ●It can set SV2 at required time and particular area as like the above chart. ● ●SV2 is in parameter 1 group. ● ●Application : The control system, which h ...

Equipment to be controlled Converter Analog output 1-5VDC 0-10VDC DC4-20mA TZ Series SSR Load power Power Voltage output terminal + - I N P U T L O A D T TZ Series DC4-20mA LOAD ...

Start Code Header Code END Code BCC Code Address Code Text STX 10 1 10 0 R/W X/D ETX FSC Supply system power ※A → Over min. 4sec, B → Within max. 300ms, C → Over min. 20ms A B C TZ/TZN S T X A D R C M D T X T E T X B C C S T X A D R C M D T X T E T X B C C A C K S T X A D R C M D T X T E T X B C C Master Interface Standard EIA RS485 Number of connections Max. 31units. It is available to set address 01 to 99. Communication method 2 wire half duplex Synchronous method Asynchronous type Communication distance Within 1.2km Communication speed 2400, 4800, 9600(avail ...

● Write of setting value In case setting value is -100 A C K S T X 0 1 W D S 0 Symbol 10 3 10 2 10 1 10 0 E T X F S C A C K S T X 0 1 W D S 0 - 0 1 0 0 E T X B C C 06 02 30 ...