Canon imagePRESS C800 Series Technical Workbook

1st Edition, October 2015 Technical Workbook This Workbook was produced and published in its entirety by: Anthony Lamirata Canon U.S.A., Inc. Engineering Systems & Support Division 1 Canon Park Melville, NY 11747 Disclaimer Information in this Workbook is based on material available prior to publication Copyright © 2015 by Canon U.S.A., Inc. This Workbook is for private use only. Any other use, reproduction or ...

Model Issues 1 Adjustment of Image Registration 2 Image Position Adjustment 3 Use Care Removing / Mounting the Induction Heating Unit 4 Use Care Mounting the Fixing Belt Displacement Control Motor Unit 5 Use Care Mounting the Pressure Belt Displacement Control Motor Unit 7 Clearing the Fixing Belt Unit Counter 9 Use Care When Mounting the Pressure Belt Unit 10 How to Adjust Pressure for Fixing Nip 15 Creases on the Fixing Belt 16 Introduc ...

1 Model Issues This Technical Workbook is a compilation of previous Technical Publications and other sources for the imagePRESS C800 /C700 /C60 Series. Material in this Workbook may also cover topics such as the recommended Maintenance Procedures, Trouble-Shooting Tips to address General Paper Handling as well as other technical or End User topics. This portion of the Technical Workbook material will focus on known issues ...

2 Adjustment of Image Registration First, all Image Position Adjustments are referenced to Magenta. So, first make certain that Magenta Image Quality is at its best in this regard. Next, the levelness of the floor can negatively affect the Image Positon. If the engine is moved even a few inches it can affect Image Registration. The Image Registration and Position Adjustments are executed based on the premises that the Med ...

3 Image Position Adjustment The Image Position Adjustment 2 is very important and many factors are involved. As previously mentioned, all Image Position Adjustments are referenced to Magenta. So again, first make certain that Magenta Image Quality is at its best in this regard. Again, the levelness of the floor can negatively affect the Image Positon. If the Engine has been moved, even a few inches, it can affect the Imag ...

4 Use Care Removing / Mounting the Induction Heating Unit When the Induction Heating (IH) Unit is inserted into the Fixing Belt Unit, E007 Errors can result if care is not used. First, fit the Hook [3] into the Front Side []of the IH Unit to the Groove [A] on the Front Side of the Fixing Belt Unit, and then fit the Hook [4] into the Rear Side [] to the Groove [B] on the Rear Side. As it is hard to see the Hook fit i ...

5 Use Care Mounting the Fixing Belt Displacement Control Motor Unit If the Fixing Belt Displacement Control Motor Unit [A] is not mounted properly, some likely issues that could occur are E007-0001, 0011, 0021.  Mount the Fixing Belt Displacement Control Motor Unit by connection of the Posts [A] and [B] to the Hole [C] and the Hook [D] of the Fixing Belt Displacement Control Motor Unit. [B]  NOTE: When mounting the ...

6  Fit the Post [B] of the Fixing Belt Unit into the Plastic U-Shaped Hole [D] of the Hook. The Post [E] on the Fixing Belt Unit should insert into the Hole [F]. 3) Place the Fixing Belt Displacement Control Motor Unit over the Boss on the Fixing Belt Unit and secure them with a New Screw. Be sure that the Metal Plate [A] of the Fixing Belt Unit does not rest on top of the Boss [B] on the Fixing Belt Displacement Co ...

7 Use Care Mounting the Pressure Belt Displacement Control Motor Unit If the Pressure Belt Displacement Control Motor Unit [A] is not mounted properly, some prospective issues that could develop are E007-0012, 0022, and 0102. 1) Mount the Pressure Belt Displacement Control Motor Unit by fitting the Posts [1], [2] and the Positioning Boss [3] on the Pressure Belt Unit to the Hook [4], the Hole [5], and the Positioning Cuto ...

8 The Shaft [1] is not seated properly due to improper positioning when mounted. Use care because the Shaft appears as if it is fitted properly when it is looked at from the front [A]. Use care to ensure the Positioning Hook [1] does not disengage from the Positioning Cutout [2] when joined together. When engaged properly, there is no gap left between the Pressure Belt Unit and the Pressure Belt Displacement Control Moto ...

9 2) After positioning the Pressure Belt Displacement Control Motor Unit, fasten it with a New Screw. Clearing the Fixing Belt Unit Counter If the Fixing Belt Unit Counter is not cleared after component replacement, or if the Fixing Belt Unit is not mounted properly, some potential issues that could arise are E007-0001, 0011 and 0021. After replacement of the Fixing Belt Unit, performance of the Operation Check from Servi ...

10 If the Grease on the moving Gears [1] of the Fixing Belt Unit is depleted, apply the Grease (SE1107) onto entire circumference of the Gear [A] surfaces as needed. After replacement of the Fixing Belt Unit, be sure to execute Counter Clear for the unit. Navigate to Service Mode: FUNCTION> DRBL-1 >FX-BLY-U " to execute the Counter Clear. If a Count Clear is not executed, the data history before replacement of the unit i ...

11 1-1) Look at the Pressure Belt Unit from its top and confirm if the Flange on the Bearing [1] is inside the Support Plate [2] and there is no gap [A] left between the Bearing and the Support Plate in side view. 1-2) If there is a gap, push the Bearing [1] from outside [A] to seat it in the correct position. [A] [2] [1] [1] [1] [A] [A] ...

12 2) Remove all the curves from the Halogen Heater Cable [1] on the front side, straighten it, and put it through the Guide [2]. 3) Remove all the curves from the Halogen Heater Cable [1] of the on the rear side, straighten it, and put it through the Guide [2]. [2] [1]  NOTE: Use care not to mount the Halogen Heater twisted.  NOTE: Use care not to mount the Halogen Heater twisted. [2] [1] ...

13 4) Open the Inlet Guide [1] of the Fixing Unit Frame. 5) Mount the Pressure Belt Unit. This will be easier if the Hinge Shaft [1] on the front side is mounted first, then the Hinge Shaft [2] on the rear side is mounted second. [1] [2] [1] ...

14 6) Connect the Halogen Heater at the two (2) locations. Use care not to insert the Halogen Heater twisted while connecting it.  NOTE: • Use care not to damage the Pressure Belt during mounting. • After replacement of the Pressure Belt Unit, Apply Grease (SE1107) respectively to the six (6) Gears [1] on the Fixing Belt Unit and the Gear [2] of the Fixing Drive Assembly. Amount to apply: about five (5) grains of r ...