DIVA Light JVT Series Installation Instruction

IMPORTANT READ CAREFULLY BEFORE INSTALLING THE FIXTURE. RETAIN THESE INSTRUCTIONS FOR FUTURE REFERENCE. THOROUGHLY INSPECT THE FIXTURE FOR ANY FREIGHT DAMAGE; FREIGHT DAMAGE SHOULD BE REPORTED TO THE DELIVERY CARRIER. The fixtures must be wired in accordance with the National Electrical Code and all applicable local codes. Proper grounding is required for safety. This product MUST be installed in accordance with the applicable installation code by a person familiar with the construction and operation of the product. This product SHALL be surface mounted with junction box or non-combustible surface above 4 feet (1.2 meter) high. User should prepare necessary accessories and spare parts (not provided) including junction box and screws. This luminaire is designed for outdoor lighting applications with ambient temperatures not exceeding 40°C. WARNING RISK OF ELECTRIC SHOCK. Make sure power supply is OFF before installing or maintaining fixture. No user serviceable parts inside. Never perform maintenance or cleaning while fixture is energized. Disconnect power and allow fixture to cool before maintaining. A regularly scheduled maintenance program should be established to retain optimum light output and reduce heat retention. Dusting with a soft, clean, dry cloth is normally sufficient for the optical system. Any accumulation of dust or dirt should be removed regularly. Dangerous voltage exists within the unit and all precautions usually observed in handling high voltage equipment should be observed when replacing light engine or otherwise servicing luminaires. Disregarding this warning could result in electrical shock and possible injury to the individual installing or servicing this equipment. WALL MOUNT Mounting Housing LED Housing Gasket Globe Guard Mounting Housing LED Housing Gasket Globe Guard CEILING/ PENDENT MOUNT

WALL MOUNT INSTALLATION 1. Attach fixture to junction box using appropriate hardware for the mounting surface. Mounting hardware not included. 2. Remove gasket inside LED Housing and remove screw closest to mounting surface. 3. Loosen other screw and rotate LED Housing 180 degrees so that the four Mounting Housing screws are easily accessible. See Rotated View below. DO NOT PINCH WIRES WHILE ROTATING. 4. Tighten LED Housing screw to ensure that no components fall. 5. Remove the four Mounting Housing screws and make wiring connections inside Mounting Housing. 6. Make wiring connections inside the Mounting Housing as per the wiring instruction. CEILING/ PENDENT MOUNT INSTALLATION 1. Attach fixture to junction box using appropriate hardware for the mounting surface. 2. Remove gasket inside LED Housing 3. Remove one screw in LED housing and loosen the remaining screw. 4. Rotate LED Housing 180 degrees and tighten the remaining screw. See Rotated View below. DO NOT PINCH WIRES WHILE ROTATING. 5. Tighten LED Housing screw to ensure that no components fall. 6. Make wiring connections inside the Mounting Housing as per the wiring instruction. WIRING 1. Wire input end of the LED driver to supply wires using waterproof wire nut (provided) according to wiring section. Wire connections must be insulated and waterproof. 2. Connect the BLACK/BROWN lead to LINE (+) supply lead. 3. Connect the WHITE/BLUE lead to NEUTRAL/COMMON (-) supply lead. 4. Connect the GREEN lead to GROUND supply lead. 5. If any, connect PURPLE/BLUE to 0-10V SIGNAL supply lead and GREY/WHITE to 0-10V NEUTRAL/REFERENCE supply lead. GLOBE AND GUARD INSTALLATION 1. Re-mount fixture using Philips Head screws removed in mounting step. Make sure all gaskets must be seated properly and all screws inserted and tightened firmly. 2. Return all components to their original positions after wiring connections have been made. Prior to tightening all screws, make sure all wires are contained in wire ways and no wires are pinched. 3. Before globe is installed, check to make sure that gasket is replaced in LED Housing and gasket exists above threads on the Globe. 4. Screw Globe onto fixture, do not over tighten but be sure that the gaskets are being compressed. 5. Place Guard over the lens, rotate clockwise and secure with set screws. 6. Turn on power. NOTE: Make sure all gaskets are positioned correctly with no gaps to ensure that leakage will not occur. ROTATED VIEW