Dynamic DX-SLM Installation Manual

Text of Dynamic DX-SLM Installation Manual

Servo Steering and Lighting Module

DX-SLM INSTALLATION MANUAL GBK60027: Issue 5 - March 2014 DX-SLM Servo Steering and Lighting Module THE ULTIMATE POWERCHAIR CONTROL SOLUTION M T M T

GBK60027 DX-SLM Installation Manual Issue 5

Contents 1 Introduction ............................................................. 3 2 Related Documentation ......................................... 4 3 General Description ............................................... 5 3.1 General Features ........................................................................ 6 3.2 Safety and Protection Features ............................................... 6 4 Speci
GBK60027 DX-SLM Installation Manual Issue 5 7.4 Calibrating the SLM using the HHP ........................................ 40 7.4.1 Initial Operation ............................................................. 40 7.4.2 Calibrating Parameters ................................................ 41 8 Diagnostics ............................................................ 43 8.1 Troubleshooting ..................................................................
GBK60027 DX-SLM Installation Manual Issue 5 1 Introduction The Servo Steering and Lighting Module (SLM) controls the steering and lighting for servo steered power wheelchairs. It is part of a DX System also comprising a DX Power Module and a DX Remote as a minimum system. Example of Minimum DX System with the SLM The servo wheelchair has one motor for steering, and either one or two motors to provide the driving power of the wheelchair. The DX Remote contr
GBK60027 DX-SLM Installation Manual Issue 5 2 Related Documentation A DX based wheelchair control system may comprise between two and sixteen DX compatible modules depending on the application. Each DX compatible module has its own Installation Manual, which describes the installation requirements of that particular module. This manual describes the installation of the SLM only and must be read in conjunction with the: • DX System Manual • Relevant DX
GBK60027 DX-SLM Installation Manual Issue 5 3 General Description The SLM is designed to enable the DX System to run on a servo steered power wheelchair, with lights. The wheelchair will have: a servo motor, a position sense potentiometer, a steering release microswitch, one or two drive motors with integral park brakes, a 24 V battery supply, and optional 24 V lights. The DX system will comprise of a minimum of a DX Remote, a DX Power Module, a SLM and ma
GBK60027 DX-SLM Installation Manual Issue 5 3.1 General Features The SLM has the following general features: • Servo output capable of supplying 5 A continuous and 30 A peak to a 24 V servo actuator. • Fully DX BUS compatible. • Two identical DX BUS sockets for Daisy Chain connection to the DX System. • Powered by a 24 V wheelchair battery via the DX BUS connection, or directly from the battery for high current applications. • Fully programmable
GBK60027 DX-SLM Installation Manual Issue 5 4 Specifications 4.1 Electrical Specifications Power Supply Input Symbol Parameter Min Nom Max Units VBAT Battery voltage 18.0 24.0 32.0 V IQ Quiescent Current (No servo load) 150 mA IO Operating Current (+ servo load) 250 mA IDXBUS DX BUS Current (RMS Continuous to entire system) 12 A Servo Motor + / - Output Symbol Parameter Min Nom Max Units SM+ Output Voltage (when not in current limit) VBAT-1.2V VBAT V IAV C
GBK60027 DX-SLM Installation Manual Issue 5 Lighting Specification Symbol Parameter Min Nom Max Units Turn Indicator Outputs (each output) VTIO Output Voltage VBAT-1 VBAT-0.1 VBAT V ITIO Continuous Output Current 2.3 2.5 A Sidelight (Head / Tail Light) Output VSLO Output Voltage VBAT-1 VBAT-0.1 VBAT V ISLO Continuous Output Current 2.3 2.5 A Page 8 M T
GBK60027 DX-SLM Installation Manual Issue 5 4.2 Mechanical Specifications Size: 210 * 123 * 38 mm Weight: 0.530 Kg Mounting: M5 screws four places, or placed in tray Case material: Aluminium sheet, powder coat finish Case sealing: Tamper proof, IP54 if mounted as per mounting instructions SLM Configuration 4.3 Environmental Specifications Symbol Parameter Min Max Units Operating ambient temperature range -25 50 °C Storage temperature range -25 70 °C Oper
GBK60027 DX-SLM Installation Manual Issue 5 5 Installation 5.1 Introduction Installing a SLM requires the following steps: 1. Mounting the SLM Refer Section 5.2 2. SLM Connection with the DX system Refer Section 5.3 3. SLM 21 Way Connector Refer Section 5.4 4. SLM Servo Connector Refer Section 5.5 5. Programming the SLM related parameters Refer Section 7.0 5.2 Mounting Optimum mounting orientation Fit the SLM with the top label facing up. Unacceptable Mo
GBK60027 DX-SLM Installation Manual Issue 5 Securing the SLM The SLM can be mounted using the four mounting holes and mounting screws provided, or placed in a suitable tray. Do not use screws that protrude into the SLM case by more than 12 mm. The SLM must be mounted in a position that offers the maximum protection from water and mechanical abuse. Since there are no user accessible controls on the SLM, it can be mounted in a position which is inaccessible
GBK60027 DX-SLM Installation Manual Issue 5 5.3 SLM Connection with the DX System 5.3.1 DX BUS Connections Note: If only one DX BUS connector is used on the SLM and the remaining connector is accessible to the wheelchair user, a GPL65009 DX BUS Connector Cover should be fitted to the unused connector. This complies with the ISO 7176-14 standard. Like all other DX Modules, the SLM is connected to the DX system using the DX BUS. Refer to the DX System Manual
GBK60027 DX-SLM Installation Manual Issue 5 5.3.2 DX Module Interconnection Topology Options The battery and DX Power Module combination are always considered the heart of a DX system. Other DX Modules can be arranged in several ways: Star DX BUS Topology In-line DX BUS Topology Mixed DX BUS Topology DX Power Module DX Module DX Module DX Module DX Module DX Module DX Module DX Module DX Module DX Module DX Module DX Remote Battery 24V D X M o d u l e D X
GBK60027 DX-SLM Installation Manual Issue 5 DX modules normally have one or two DX BUS sockets for system interconnections. Smaller DX modules may have a permanently mounted cable terminated in a DX BUS plug, rather than DX sockets. The star and mixed topologies both require the use of one or more DX BUS Expanders (DX-SKT-X3). The DX-SKT-X3 may be purchased from Dynamic Controls or a Dealer. For lowest cost and simplicity the in-line topology is generally
GBK60027 DX-SLM Installation Manual Issue 5 Example: Consider a Power Module connected to an SLM via five other DX Modules using 1 metre cables. Example of DX Module interconnection The total resistance of the 0 V return path, between the Power Module and SLM is: 6 X (2 * Rct + Rca) = 111 mOhms This means that the maximum load that the SLM can drive and not exceed the1.0 V drop requirement is 1 / 0.111 = 9 A. If, for example, the servo motor and lighting
GBK60027 DX-SLM Installation Manual Issue 5 This favours topologies such as: Rationalised In-line Topology Two-way star Topology Multi-star Topology D X P o w e r M o d u l e B a t t e r y 2 4 V H i g h C u r r e n t M o d u l e s N e a r e s t P o w e r M o d u l e L o w C u r r e n t M o d u l e s F u r t h e s t a w a y f r o m Power Module H H H L L D X P o w e r M o d u l e B a t t e r y 2 4 V H L L H L L D X P o w e r M o d u l e B a

Dynamic Wheelchair Owners Instructions: