Fanvil i20S Quick Installation Manual

1. Package Contents.............................................................................. 4 2. Physical Specifications ...................................................................... 4 3. Installation ........................................................................................ 8 4. Searching Door Phone .................................................................... 11 5. SIP Door Phone Setting ................................................................... 12 6. Door Unlocking Setting ................................................................... 13

2. Physical Specifications Device size 160 x 93 x 35 mm Weight 420g (gross weight) 1) Front Panel Door Phone Connectors Quick Installation Guide RFID Cards Screw and Wrench MIC RFID Reader Numeric Keyboard DSS Key Lock Call & Ring Network & SIP Registration Speaker

and alert use. MIC The door phone has a built-in microphone hidden in the pinhole located on the front panel. RFID Reader Use RFID cards to unlock the door by touching RFID reader of device. Button Definition Button Description DSS Key Press the Button, calling or request to open the door. Numeric Keyboard Input password to open the door or call. LED Definition LED Status Description Lock Steady Blue Door unlocking off Door locking Call & Ring Blinks per second Call Hold or Ringing off On Hook Blinks every 3 seconds Device in the issuing state Steady Blue Online talking Network & SIP Registration Blinks per second Network error off Network is normal, SIP is not registered Blinks every 3 seconds SIP Registration failed Steady Blue SIP Registration succeeded 2) Port Definition After removing the Back Panel of i20S, there are one terminal block connectors for power and lock control connection as shown in the picture below. JP1 Jumper Power and lock connector Network port

COM: Common Contact NC: Normally Close Contact Driving Mode Electric-lock Mode JP1 Jumper Connections Active Passive No electricity when open Electrify when open √ √ √ √ √ √ √ √ √ √

Figure 1 Three Major Parts of i20S Step 1: Installation preparation A. Check the following contents:  Hex wrench x 1  RJ45 plugs x 2 (1 spare)  KA4 x 25mm screws x 4  25mm screw anchors x4 B. Tools that may be required:  Hex wrench  Phillips screwdriver (Ph2 or Ph3), hammer, RJ45 crimper  Electric impact drill with an 6mm drill bit Step 2: Drilling Figure 2 Wall Mounting A. Place the mounting template with dimensions on the surface of a wall in a desired flat position. B. Use an electric drill to drill the 4 holes marked on the mounting template. It is recommended to drill about 30mm deep. Remove the template when finishing drilling. C. Push or hammer screw anchors into the drilled holes.

A. Remove the hanging shell in Figure 3 and Figure 4. Figure 3 Figure 4 B. With Phillips screwdriver, unpacks the Back Panel and the main part of intercom as shown in Figure 5. Figure 5 Step 4: Hanging shell Fixing and Cabling Figure 6 A. Select the hole for cable supply; cable length of 15cm to 20cm is recommended. B. With 4 KA4 x 25mm screws, tighten the Wall-mounted hanging shell as shown in Figure 6.

Figure 7 Figure 8 A. Select the hole for cable supply. B. Connect the cables of RJ45, power, and electric-lock to the motherboard socket as mentioned in connectors description (refer to Section 2). C. Test whether there is electricity by doing the following: Press the # button for 3 seconds to get the IP address of intercom by voice. Input access password or press the indoor switch to check electric-lock installation. Note: Do not proceed mounting until you have finished the electric checking. Step 6: Mounting Figure 9 Figure 10 A. Use the 4 screws to tighten the main part of intercom on the back panel as shown in Figure 9. B. Push the device into the Wall-mounted hanging shell and tighten it with 1 screw as shown in Figure 10. C. Make sure the screws have been tightened properly for better waterproof effect.

There are two methods as shown below to search the i20S. Method 1: Open the iDoorPhone Network Scanner. Press the Refresh button to search the i20S and find the IP address. (Download address http://download.fanvil.com/tool/iDoorPhoneNetworkScanner.exe ) Method 2: Press and hold the “#” key for 3 seconds and the door phone will report the IP address by voice. Default Setting Default DHCP Client On Static IP Address 192.168.1.179 Default Web Port 80 Default Login User Name admin Default Login Password admin Display IP address Hold # for 3 seconds to display by voice Search Tools iDoorPhone Network Scanner

Step 1: Login the homepage of the i20S. Step 2: Add the SIP account. Set SIP server address, port, user name, password and SIP user with assigned SIP account parameters. Select “Activate”, and then click Apply to save this setting. Step 3: Setting DSS key Set the DSS key as shown below for a quick start. Click “Apply” to save this setting. Type: Hot Key Number 1: The DSS Key will dial to this Number 1. Number 2: If Number 1 is unavailable, it will be forwarded to Number 2. Line: Working line Subtype: Speed dial

6. Door Unlocking Setting Local 1) Local Password Step 1: Go to EGS Setting → Features → Set Local Password (The default is “6789”). Step 2: Use the device’s Numeric Keyboard to input password and “#” key, and then the door will be unlocked.

Step 1: Go to EGS Access → Access Rule → set Access Code. Step 2: Use the device’s Numeric Keyboard to input password and “#” key, and then the door will be unlocked. Remote Remote Password Step 1: Go to EGS Setting → Features → Set Remote Password (The default is “*”). Step 2: To answer the call made by visitor via SIP phone, press the “*” key to unlock the door the visitor. RFID Card Step 1: Go to EGS Access → Enter the Name and ID Number (Only Front 10 yards) → Press Add to Access Table. Step 2: Use pre assigned RFID cards to unlock the door by touching RFID area of device.