Kaba Mas LA Gard Combogard 33E Manager Programming
Text of the manual
3040-DB Deadbolt Lock & 4100 Swingbolt Lock
Manager prograMMing
STANDARD FEATURES
WRONG TRY PENALTY
•� Four�(4)�consecutive�invalid�combinations�initiates�five�(5)�minute�delay�period.
LOW BATTERY WARNING
•� Repeated�LED�flashing�and�beeping�during�opening�indicates�battery
� is�low�and�needs�immediate�replacement.
AUDIO AND VISUAL SIGNAL
•� Double�signal�-�two�(2)�LED�flashes�and�two�(2)�unit�beeps�-�indicates
� entry�is�valid�or�accepted.��
•� Triple�signal�-�three�(3)�LED�flashes�and�three�(3)�beeps�-�indicates
� invalid�or�not�accepted.
PROGRAMMABLE MODES
ACTIVE
(3045 Handheld Programmer Required)
MANAGER COMBINATION�(Factory�set�to�1-2-3-4-5-6)�...............£
•� Add/Remove�User
•� Enable/Disable�User
USER COMBINATION�.....................................................................£
•� Open�Lock
•� Change�Combination
TIME DELAY OVERRIDE MODE�....................................................£
•� Ability�to�add�second�combination�to�override�delay�period
DUAL COMBINATION MODE�.........................................................£
•� Add�User
•� Both�combinations�required�to�open
PROGRAMMABLE FEATURES (3045 Handheld Programmer Required)
TIME DELAY�....................................................................................£
•� Delay�period�1�-�99�minutes
•� Open�period�1�-�19�minutes
SILENT SIGNAL ALARM�(Optional�Alarm�Box�Required)�...............£
•� Duress�signal�if�last�number�of�combination�is�entered�using�one
� number�higher�or�one�number�lower.
DISABLE LOCK�(Optional�Alarm�Box�Required)�.............................£
•� Input�signal�disables�opening�of�lock�by�valid�combination.
OPENING THE LOCK
1.�Enter�valid�six�(6)�digit�combination.
2.�The�lock�will�indicate�a�valid�combination�with�a�double�signal.
3.�Within�four�(4)�seconds,�turn�the�keypad�to�the�open�position
� (clock-wise)�if�using�a�dead�bolt�style�lock,�or�turn�the�handle�to�the
� open�position�if�using�a�swing�bolt�style�lock.
4.�Pull�door�open.
•� Invalid�Combination�-�Lock�will�signal�three�(3)�times.
CHANGING YOUR COMBINATION
ALWAYS PERFORM THIS OPERATION WITH THE DOOR OPEN
(If your unit is programmed for Dual Mode, each combination must
be changed independently. Follow these instructions for each
combination change.)
1.�Enter�“zero”�six�times.
2.�Enter�your�existing�six�(6)�digit�combination�one�time.
3.�Enter�your�NEW�six�(6)�digit�combination�two�times.
4.�If�a�mistake�is�made�wait�thirty�(30)�seconds�and�repeat�steps�1�-�3.
5.�Test�lock�operation�several�times�before�closing�the�door.
CAUTION: When selecting a combination do not use birthday or
other predictable data that could give correlation between the
user and the combination. Keep the combination secret.
•� Valid�Combination�-�Double�signal�after�valid�six�(6)�digit
� combination�is�entered.
•�Invalid�Combination�-�Triple�signal�indicates�the�old�combination�is
� still�valid.
ADD USER�(ONLY available if either Manager Mode, Time Delay
Override Mode or Dual Mode was activated using the 3045 Hand Held
Programmer. Add User is not available if Remote Override feature is
activated using the 3045 Hand Held Programmer.)
ALWAYS PERFORM THIS OPERATION WITH THE DOOR OPEN
1.�Enter�the�Manager�combination�and�hold down last digit of the
combination until the lock signals with two sets of double beeps.
2.�PRESS 1.�Lock�signals�as�follows:
� � One�beep�–�User�is�already�installed�(end�of�operation)
� � Two�beeps�–�User�enabled,�go�to�Step�3�
� � Three�beeps�–�Not�available;�Function�was�not�programmed�with
� � Hand�Held�Programmer�(end�of�operation)�
3.�Enter�NEW�user�combination�twice.�The�lock�signals�twice�after
� each�valid�entry.
4.�If�a�mistake�is�made�wait�thirty�(30)�seconds�and�repeat�steps�1�-�3.
©�copyright�2006��
(P/N)12-203�v5�•�6/08�
Kaba Mas LLC
page�1�of�2
4200�Swingbolt�Lock
3740-2�Deadbolt�Lock
SUggESTED�KEyPADS:
3035�Entry
3750�Entry
3190�PrivatII�(Optional)
DISABLE USER�(Manager only.)
ALWAYS PERFORM THIS OPERATION WITH THE DOOR OPEN
1.�Enter�the�Manager�combination�and�hold down last digit of the combination until the lock signals with two sets of double beeps.
2.�PRESS 2.�Lock�signals�once.
3.�User�is�temporarily�disabled.�(User�combination�is�saved�and�will�be�valid�if�reinstated)
4.�If�a�mistake�is�made�wait�thirty�(30)�seconds�and�repeat�steps�1 - 3.
REINSTATE USER�(Manager only.)
ALWAYS PERFORM THIS OPERATION WITH THE DOOR OPEN
1.�Enter�the�Manager�combination�and�hold down last digit of the combination until the lock signals with two sets of double beeps.
2.�PRESS 1.�Lock�signals�once.
3.�User�is�reinstated.�
4.�If�a�mistake�is�made�wait�thirty�(30)�seconds�and�repeat�steps�1 - 3.
REMOVE USER(Manager only.)
ALWAYS PERFORM THIS OPERATION WITH THE DOOR OPEN
1.�Enter�the�Manager�combination�and�hold down last digit of the combination until the lock signals with two sets of double beeps.
2.�PRESS 3.�Lock�signals�once.
3.�User�and�combination�are�removed�from�the�lock.��(Add�User�feature�is�still�available.)
4.�If�a�mistake�is�made�wait�thirty�(30)�seconds�and�repeat�steps�1 - 3.
DUAL MODE OPERATION (If mode is active. Must be programmed using 3045 Hand-Held Programmer)
1.�Must�add�User�to�open�lock.�(See�ADD USER)
� •� User�cannot�be�disabled�or�removed.
2.�If�Time�Delay�is�active,�one�valid�combination�will�start�Delay�period.
� •� Both�combinations�required�to�open�lock�in�Open�period.
TIME DELAY OVERRIDE�(If�mode�is�active.�Must�be�programmed�using�3045�Hand-Held�Programmer)
1.�Must�add�User�to�use�this�mode.�(See�ADD USER)
� •� User�cannot�be�disabled�or�removed.
2.�Entering�Override�User�combination�during�Delay�period�will�open�the�lock.
PROGRAMMABLE LOCK FEATURES�(Time delay and silent alarm features may be combined with any programmable lock mode.)
TIME DELAY�(If feature is active. Must be programmed using 3045 Hand-Held Programmer.)
1.�Entering�a�valid�combination�begins�the�Delay�period.
� •� LED�flashes�at�one�(1)�second�intervals.
� � -�If�a�valid�combination�is�entered�during�the�Delay,�then�Delay�period�restarts.
� � -�If�an�invalid�combination�is�entered�during�Delay,�then�the�Delay�period�aborts.
2.�At�end�of�Delay�period,�the�Open�period�begins.
� •� LED�flashes�at�1/2�second�intervals�and�the�entry�beeps�at�ten�(10)�second�intervals.
� � -�If�a�valid�combination(s)�is�entered�during�the�Open�period,�then�the�lock�will�open.
� � -�If�an�invalid�combination�is�entered�during�Open�period,�then�the�Open�period�continues.
� •� Four�(4)�consecutive�invalid�combinations�entered�will�start�the�Wrong�Try�Penalty.
SILENT SIGNAL ALARM�(If feature is active AND optional Alarm Box [2789 or 4002] is connected to an alarm system.)
1.�To�send�an�alarm�signal�enter�last�digit�of�combination�one�number�higher�or�one�number�lower.
� � •�Example:�Combination:�1-2-3-4-5-6
� � •�Duress:�1-2-3-4-5-5�or�1-2-3-4-5-7
2.�The�lock�will�open�without�any�indication�that�the�duress�signal�has�been�sent.
DISABLE LOCK�(If feature is active the alarm box [2789 or 4002] is required. ONLY the Manager is available)
Input�signal�to�the�alarm�box�will�disable�opening�of�the�lock�by�a�valid�combination.
WRONG TRY PENALTY
� •� Entry�of�four�(4)�consecutive�invalid�combinations�starts�a�five�(5)�minute�delay�period.
� � -�LED�flashes�at�ten�(10)�second�intervals.
� •� At�the�end�of�the�delay�period,�two�more�consecutive�invalid�combinations�will�restart�the�five�(5)�minute�delay�period.
� � Entry will not respond to keystrokes during delay period.
BATTERY LOW WARNING
Repeated�LED�flashing�and�beeping�during�an�opening�indicates�that�the�battery�is�low�and�needs�immediate�replacement.
� •� Uses�alkaline�battery�only.�(Example:�Duracell™�or�Eveready™�alkaline�batteries.)�It�is�recommended�that�batteries�are�replaced�at�least
� � once�a�year.
� •� For�battery�replacement�instructions,�see�the�input�unit’s�“User�Operating”�guide.
� � Lock contains a nonvolatile memory; even with batteries removed the lock will retain all programming.
Mounting instructions are available at www.kaba-mas.com.
©�copyright�2006��
(P/N)12-203�v5�•�6/08�
Kaba Mas LLC
page�2�of�2