Cisco Catalyst X4232 Installation And Configuration Note

Copyright 2001. Cisco Systems, Inc. All rights reserved. 78-10164-03 Installation and Configuration Note for the Catalyst 4000 Layer 3 Services Module Product Numbers: WS-X4232-L3(=) This installation and configuration note describes how to install and configure the Catalyst 4000 Layer 3 Services module. For a complete description of commands to configure Cataly ...

78-10164-03 Software Requirements • Configuration Options, page 40 • Configuring the Layer 3 Services Module Gigabit Ethernet Interfaces, page 42 • Configuring the Module for InterVLAN Routing, page 44 • Configuring Access Control Lists, page 60 • Configuring Layer 3 QoS, page 67 • Configuring the Switching Database Manager, page 74 • Obtaining Documentation, ...

78-10164-03 Features Layer 3 Routing, Switching, and Forwarding Features IP, IPX, and IP multicast routing and switching between Ethernet ports CMF3 Load balancing among equal cost paths based on source and destination IP and IPX addresses Load balancing on a per-destination basis CEF load balancing on Gigabit Ethernet ports using tunnel or universal load balancing algorith ...

78-10164-03 Features Unsupported Features The following major features are not supported on the Catalyst 4000 Layer 3 Services module: • Multilayer Switching (MLS) • IPX extended access lists Additional Protocols and Features (continued) SDM15 BOOTP16 CDP17 support on Ethernet ports CGMP18 server support DHCP19 relay HSRP20 ICMP21 IGMP22 IPX SAP and SAP23 filtering SNMP ...

78-10164-03 Configuring IOS Features • Named IPX SAP access lists • 48-bit MAC access lists • 48-bit MAC extended access lists • Integrated routing and bridging (IRB), and concurrent routing and bridging (CRB) • ISL trunking on the internal Gigabit Ethernet ports If a feature does not appear in the list of supported features in this document or in the list of supp ...

78-10164-03 Functional Description Note The default TCAM size allocated for access lists by the Switching Database Manager is 1024. If your access list configurations exceed this default size, you can reconfigure the TCAM allocation. See the “Configuring the Switching Database Manager” section on page 74 for information on allocating TCAM space. Note Access lists are su ...

78-10164-03 Front Panel Description The Catalyst 4000 Layer 3 Services module occupies a single slot in the chassis and has two internal full-duplex Gigabit Ethernet interfaces that connect directly to the Catalyst 4000 family switch backplane to provide routing capability to all Layer 2 switch ports in the switch. In addition, there are two external Layer 3 Gigabit Etherne ...

78-10164-03 Front Panel Description LEDs Table 3 describes the LEDs on the Catalyst 4000 Layer 3 Services module. Connectors Table 4 lists the front panel connectors on the Catalyst 4000 Layer 3 Services module. Table 3 LEDs on the Catalyst 4003 and 4006 Layer 3 Services Module LED State Description STATUS (module) This LED displays the results of a series of self-tests and ...

78-10164-03 Specifications Specifications Table 5 lists the specifications for the Catalyst 4000 Layer 3 Services module. Table 5 Catalyst 4003 and 4006 Layer 3 Services Module Specifications Specification Description Dimensions (H x W x D) 1.18 x 15.51 x 16.34 in. (30 x 394 x 415 mm) Weight Minimum: 3 lb. (1.36 kg) Maximum: 5 lb. (2.27 kg) Environmental conditions: Operati ...

78-10164-03 Standards Compliance Specifications Standards Compliance Specifications When properly installed in the chassis, the Catalyst 4000 Layer 3 Services module complies with the standards listed in Table 6. Gigabit Interface Converters A gigabit interface converter (GBIC), shown in Figure 2, is a hot-swappable I/O (transceiver) device that plugs into the module’s G ...

78-10164-03 Gigabit Interface Converters Note Cisco 1000BASE-LX/LH interfaces fully comply with the IEEE 802.3z 1000BASE-LX standard. However, the higher optical quality of the 1000BASE-LX/LH allows them to reach 10 km over single-mode fiber (SMF), as compared to the 5 km specified in the standard. Note Because of interoperability issues, Cisco does not support GBICs purch ...

78-10164-03 Gigabit Interface Converters GBIC Optical Power Characteristics Table 8 provides the optical power characteristics of the GBIC. GBIC Cabling Restrictions You must observe the following optical-fiber cabling restrictions when using GBICs: • The minimum cabling distance for 1000BASE-SX and 1000BASE-LX/LH GBICs is 6.5 feet (2 meters). • When using the 1000BASE ...

78-10164-03 Safety Overview Safety Overview Safety warnings appear throughout this publication in procedures that, if performed incorrectly, may harm you. A warning symbol precedes each warning statement. Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with e ...

78-10164-03 Safety Overview Warning AvvertenzaQuesto simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di lavorare su qualsiasi apparecchiatura, occorre conoscere i pericoli relativi ai circuiti elettrici ed essere al corrente delle pratiche standard per la prevenzione di incidenti. La traduzione delle avvertenze riporta ...

78-10164-03 Translated Safety Warnings Translated Safety Warnings This section translates in multiple languages the warnings for the Catalyst 4000 Layer 3 Services module. Warning Definition Warning This warning symbol means danger. You are in a situation that could cause bodily injury. Before you work on any equipment, be aware of the hazards involved with electrical circ ...

78-10164-03 Translated Safety Warnings Safety Information Referral Warning Avvertenza Questo simbolo di avvertenza indica un pericolo. La situazione potrebbe causare infortuni alle persone. Prima di lavorare su qualsiasi apparecchiatura, occorre conoscere i pericoli relativi ai circuiti elettrici ed essere al corrente delle pratiche standard per la prevenzione di incidenti ...

78-10164-03 Translated Safety Warnings Qualified Personnel Warning Varoitus Ennen kuin asennat järjestelmän tai käytät tai huollat sitä, lue Asennuspaikan valmistelu-jaturvaopas -opasta. Tässä oppaassa on tärkeitä turvallisuustietoja, jotka tulisi tietää ennen järjestelmän käyttämistä. Attention Avant d'installer le système, de l'utiliser ou d'assurer son ...

78-10164-03 Translated Safety Warnings Blank Faceplate Installation Requirement Warning Avertissement Tout installation ou remplacement de l'appareil doit être réalisé par du personnel qualifié et compétent. Achtung Gerät nur von geschultem, qualifiziertem Personal installieren oder auswechseln lassen. Avvertenza Solo personale addestrato e qualificato deve essere au ...

78-10164-03 Translated Safety Warnings Invisible Laser Radiation Warning (other versions available) Warnung Unbeschriftete Aufspannplatten (Füllpaneelen) erfüllen drei wichtige Funktionen : sie schützen vor gefährlichen Spannungen und Elektrizität im Innern der Chassis; sie halten elektromagnetische Interferenzen (EMI) zurück, die andere Geräte stören könnten; und ...

78-10164-03 Removing and Installing a Layer 3 Services Module Removing and Installing a Layer 3 Services Module The following sections describe how to remove and install modules, GBICs, and cables: • Required Tools, page 21 • Removing Modules, page 21 • Installing the Layer 3 Services Module, page 22 • Installing a GBIC, page 24 • Attaching Interface Cables to th ...