Grace Company Continuum II Assembly & Use

Text of the manual

Copyright September 18, 2020

Grace Company (Reproduction Prohibited) Version 1.0 Just purchased your frame? Save time setting it up by following the instructions in this manual! 12 Foot Frame - Assembly & Use

Included Parts & Tools ....................................................................................3

Extended Frame Assembly ..............................................................................4 Step 1 - Setting the Frame Height .........................................................................................................5 Step

Included Parts & Tools

Please make sure all pieces are included in your kit. Middle Leg CII-09-14523 See page 5, 47 Middle Leg Brace (x2) CII-04-14504 See page 7, 47 Track Support Connector (x2) CNT-04-11041 See page 12, 42 2 ft Table Section CII-09-14639 See page 7, 42 12 ft Plastic Track (x4) CII-05-10561 See page 12, 42 2 ft Rail Sections (x3) CII-04-11

Extended Frame Assembly

This section describes the steps for setting up the frame if the base frame has not yet been assembled. For steps on extending a frame that has already been set up, see “Upgrade Existing Frame” on page 38. Tip: For additional help, scan the QR code below with the camera on your smart phone to visit our online support videos! htt

Extended Frame Assembly

Step 1 - Setting the Frame Height Parts & Tools Needed: Right Leg Left Leg Middle Leg (x2) Open-ended Wrench 10 mm & 13 mm 14 14 17 Allen Wrench 5 mm Instructions The frame height is most easily adjusted prior to frame assembly. Please take the following steps: On all legs: Remove the M8 x 55 mm SBHCS height screws, washer, and nut

On all legs: Raise the top of the leg until

the leg is the desired height. Re-install the height screws, washer and nut. 3 Important: Set all the legs to the same height hole. On all legs: Re-tighten the set screws with the 4 mm Allen wrench. The middle leg has only one set screw. 4 Note: Final height may vary slightly after adjusting the leveling feet (se

On all table sections (long and short): Use the 4 mm T-handle Allen wrench to remove the

M6 x 8 mm connector bolts attaching the metal track supports. 1 Step 2 - Building the Frame Table Parts & Tools Needed: 14 17 Allen Wrench 5 mm SBHCS Screw M8 x 16 mm (x40) Table Section (x2) Corner Brace (x4) Middle Leg Brace (x4) Extended Frame Assembly Left Leg Midd

Building the Frame Table (Continued)

Extended Frame Assembly 2 Attach one of the corner braces to the top left corner of the frame with the 5 mm Allen wrench and four M8 x 16 mm SBHCS screws. 4 Use two M8 x 16 mm SBHCS screws and the 5 mm Allen wrench to attach the left table section to one of the the middle legs. M8 x 16 mm SBHCS (x2) Use two M8 x 16 mm

Use two M8 x 16 mm SBHCS screws to attach the right frame leg to the underside of the

remaining table section. Tighten with the 5 mm Allen wrench. M8 x 16 mm SBHCS (x2) Table Section Right Frame Leg Carefully lift the table to a standing position. 5 6 Building the Frame Table (Continued) Extended Frame Assembly 7 Use two M8 x 16 mm SBHCS screws and the 5 m

Attach one of the corner braces to the top right corner of the frame with the 5 mm Allen

wrench and four M8 x 16 mm SBHCS screws. M8 x 16 mm SBHCS (x4) Corner Brace Note: Keep table and leg as square as possible while attaching brace. 8 Line up the two table sections so there is about 2 feet of space between them. 8 Carefully lift the second half of the

Other Sewing Machine Accessories Manuals