IFM ZZ0600 Instructions For Setup
Text of IFM ZZ0600 Instructions For Setup
Fluid monitoring system - Application package
2
Contents
1 Preliminary note � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � � �3
1�1 Symbols used� � � � � � � � � � � � � � � � � � � � � � �
Fluid monitoring system - Application package UK
1 Preliminary note
You will find detailed instructions, technical data, approvals and further information using the QR
code on the individual units / packagings or at www�ifm�com�
1.1 Symbols used
►
Instruction
>
Reaction, result
[…]
Designation of keys, buttons or indications
→
Cross-reference
Important note
Non-compliance may result in malfunction or interference�
Information
Supplementary
Fluid monitoring system - Application package 4
2 Safety instructions
●
The devices described are integrated into a system as components�
– The manufacturer is responsible for the safety of the system�
– The system manufacturer undertakes to perform a risk assessment and to create a documentation
in accordance with legal and normative requirements to be provided to the operator and user of the
system� This documentation must contain all necessa
Fluid monitoring system - Application package UK
5 Function
5.1 Fluid monitoring system
The ZZ0600 fluid monitoring system contains the following components:
●
SM6000 flow meter for monitoring and display of the flow temperature and the cooling water
volumetric flow quantity� The setting of 2 switch points allows the detection of overflow (leakage / burst
pipes / worn caps).
●
String regulator valve to regulate the volumetric flow quantity
●
TA24
Fluid monitoring system - Application package 6
2
1
ZZ0600
5
LR DEVICE
+
3
4
Fig� 1: Overview application package
1: Power supply
2: AL13nn IO-Link master
3: SM6000 flow meter
4: TA2405 temperature sensor
5: ifm memory stick with LR DEVICE parameter setting software
6 Installation
► Disconnect the power of the machine before installation�
► Adhere to the instructions enclosed to the individual devices�
6.1 Fluid monitoring system
► Mount the fl
Fluid monitoring system - Application package UK
► Use 2 mounting screws and washers of size M5 for fixing�Tightening torque: 1�8 Nm�
6.3 Power supply
► Integrate the power supply into the control cabinet� The following has to be observed:
– Suited for DIN rails according to EN 60715 with a height of 7�5 or 15 mm�
– Align the input terminals downwards�
– In case of continuous full load adhere to the following installation distance
Fluid monitoring system - Application package 8
AL1350
2
1
3
5
4
7
6
1: IoT interface to the PC with LR DEVICE
2: Not connected
3: Power supply
4: SM6000
5: TA2405
6: Not connected
7: Not connected
5 Set-up
When the operating voltage has been applied, the components of the application package function
according to the factory settings. The LEDs show the status of the devices and interfaces (→ Instructions
of the individual components).
5.1 Install LR DEV
Fluid monitoring system - Application package UK
Example:
Parameter
Ethernet interface (PC)
IoT interface (IO-Link master)
IP address
192�168�0�50
192�168�0�1
Subnet mask
255�255�255�0
255�255�255�0
Gateway address
0�0�0�0
0�0�0�0
► Click on the symbol [ IO-LINK ] to write the changed values to the IO-Link master�
>
LR DEVICE reads the unit with the changed values once again�
>
LR DEVICE has access to the paramet
Fluid monitoring system - Application package 10
7 Operation
7.1 Monitor the process data
In normal operation, LR DEVICE can display the process data of the application package graphically�
In LR DEVICE:
► Click on the symbol [ IO-LINK ] to scan the network for available devices�
>
LR DEVICE finds the connected IO-Link master�
► In the [ONLINE] area: Click on the IO-Link master found�
► Click on the symbol [Cockpit]�
>
The current state and