Flowserve Valtek MaxFlo 3 Installation Operation & Maintenance
Text of Flowserve Valtek MaxFlo 3 Installation Operation & Maintenance
User instructions - MaxFlo 3 - VLENIM0052-02 02.07
1
Valtek MaxFlo 3
Control Valves
Installation
Operation
Maintenance
USER INSTRUCTIONS
User instructions - MaxFlo 3 - VLENIM0052-02 02.07
2
1
GENERAL INFORMATION
1.1
Use
The following instructions are designed to assist in the
unpacking, installation, and maintenance as required for
Flowserve products. Product users and maintenance
personnel should thoroughly review this manual prior to
installing, operating, or performing any maintenance.
In most cases, Flowserve accessories, actuators and
valves are designed for specific applications (
User instructions - MaxFlo 3 - VLENIM0052-02 02.07
3
STOP!
WARNING: Before products are returned to Flowserve
for repair or service, Flowserve must be provided with a
certificate that confirms that the product has been decon-
taminated and is clean. Flowserve will not accept deliver-
ies if a certificate has not been provided (a form can be
obtained from Flowserve).
1.8
Storage
In most cases, Flowserve products are manufactured
from stainless steel. Pr
User instructions - MaxFlo 3 - VLENIM0052-02 02.07
4
Table I: Line Flange Bolting Specifications
4
QUICK-CHECK
Before commissioning, check the control valve by fol-
lowing these steps:
4.1
Check for full stroke by varying the instrument signal
settings appropriately. Observe the plug position in-
dicator located on the actuator or the positioner. The
plug should change position with a smooth turning
movement.
4.2
Check all air connections for leaks.
User instructions - MaxFlo 3 - VLENIM0052-02 02.07
5
Item 117
Packing box nuts
Item 109
Packing box studs
Item 80
Gland flange
Item 87
Packing follower
Item 114
Bonnet nuts
Item 108
Bonnet studs
Item 93
Packing spacer
Item 88
Packing set
Item 99
Packing stop
Item 40
Bonnet
Item 42
Purge plug (optional)
Item
User instructions - MaxFlo 3 - VLENIM0052-02 02.07
6
6
VALVE DISASSEMBLY
WARNING: To carry out this operation, it is essential to
disconnect the valve from the pipework. Depressurize
line to atmospheric pressure and drain all fluids before
working on the valve. Failure to do so can cause serious
injury. Remove the valve from the pipeline.
Refer to figure 1 to find parts according to the item num-
bers.
6.1
Remove the actuator from the body by separati
User instructions - MaxFlo 3 - VLENIM0052-02 02.07
7
7.10
Place the bonnet gasket (item 58) on the gasket step in-
side the body. Gently push the bonnet into the bonnet
bore.
NOTE: When installing the bonnet, orient the milled faces
on the bonnet perpendicular to the flanges of the valve
body.
7.11
Place the packing stop (item 99) into the bonnet, then in-
stall the packing spacer (item 93) and packing as shown
in figure 3.
7.12
Install bonnet nuts an
User instructions - MaxFlo 3 - VLENIM0052-02 02.07
8
8
SEAT REPLACEMENT
WARNING: The actuator must be removed from the valve
body prior to replacing the seat ring.
8.1
To replace the seat, see figures 4 and 5, and proceed as
follows:
8.2
Loosen the packing box nuts.
8.3
Using the appropriate retainer tool (see Table III), re-
move the seat retainer. (Retainer tools are available from
the factory).
8.4
Remove the seat and any shims that may be install