Ashly mXa-1502 Operating Manual
Text of Ashly mXa-1502 Operating Manual
16 x 4 Mixer
Comprehensive DSP
Two channel Amplifier
Operating Manual
• Click the yellow box on any page to return to the table of contents
mXa-1502 • Operating Manual
2
mXa-1502 • Operating Manual
Important Safety Instructions • Consignes de sécurité à lire attentivement
The lightning flash with arrowhead symbol, within
an equilateral triangle, is intended to alert the
user to the presence of uninsulated “dangerous
voltage” within the product’s enclosure that may
be of sufficient magnitude to constitute a risk of
electric shock to persons. The exclamation point
within
mXa-1502 • Operating Manual FCC Compliance
This device complies with part 15 of the FCC
Rules. Operation is subject to the following two
conditions:
■ This device may not cause harmful
interference
■ This device must accept any
interference received, including
interference that may cause undesired
operation
Note: This equipment has been tested
and found to comply with the limits for a
Class B digital device, pursuant to part 15
of the FCC Rul
mXa-1502 • Operating Manual 4
mXa-1502 • Operating Manual
Table of Contents
1
Introduction ...................
1.1 Product overview ................
1.2 Product features .................
2
Installation Requirements ...
2.1 Electrical and wiring ...........
2.2 Mechanical ........................
2.3 Cooling ..............................
2.4 Network .............................
2.5 Browser & resolution ...........
3
Front Panel Features
Thank you for your purchase of the mXa-1502
Mixer Amplifier. This product combines state
of the art Class D multi-mode amplifier design
with eight mic inputs and 4 stereo line inputs
for a total of 16 analog inputs.
The mXa-1502 comes standard with
comprehensive DSP processing including
ducking, matrix mixing, tone generation,
integrated Ethernet control using Ashly
AquaControl™ software, remote control,
triggered/scheduled events, auxil
Air vents on the front and side panels must
have access to free flowing room temperature
air. Air is drawn in through the front-right and
right-side vent holes and blown out through
the front-left vent holes. It is not necessary
to leave empty rack spaces above or below
the amplifier. See the BTU/hr table in the
specifications section for thermal output
characteristics.
2.4 Network
The mXa-1502 is compatible with 10MB,
100MB, or 1GB Ethernet. C
Sleep LED turns on when the amplifier is in
sleep mode, as configured in software. To set
sleep mode on/off, plus set the audio inactivity
time before the amplifier goes to sleep, go to
[Settings>Panels>Front Panel].
The Disable LED is lit when the power switch
has been disabled from software.
3.7 Power Switch
The power switch turns the unit on or off, and
also flashes when in standby. The power switch
can be disabled in software. To disable the
power swit
4.11 Output Mode
This DIP switch independently configures
channels 1 & 2 for low impedance, 25V, 70V,
or 100V output. When the amplifier is set to
bridge mode, the channel 1 DIP switch settings
determine output mode.
4.12 Speaker Outputs
Use this connector to wire amplifier outputs
to speakers or to constant voltage line
transformers. The 7.62mmm Euroblock
connectors accept up to 12 ga. speaker wire.
4.13 AC Inlet
Used for the detachable AC cord. Use
6) Double-click on the index.html link to
launch the software. Proceed to step 7.
7) Log in to AquaControl software. Enter your
username and password and press the Log In
button. If this is the first log-in to a new unit,
use the factory default credentials “admin” for
login name and “secret” for password.
5.2 OSX
1) From the desktop, click , then click on
. The list of all Network devices will
start populating. Wait up to several minu