Creative Playthings SH304-101 Assembly Manual

Text of Creative Playthings SH304-101 Assembly Manual

Angled Rail 2 x 4 x 108"

B 1 33602-102 Center Rail 2 x 4 x 108" C 9 32298-102 Rock Board 5/4 x 6 x 46" D 9 32299-102 Spacer Board 5/4 x 6 x 46" E 1 33565-102 Top Rope Board 5/4 x 6 x 46" F 1 32300-102 Bench Seat 2 x 6 x 40" G 2 32301-102 Bench Support 2 x 6 x 10-5/8" H 1 32302-102 Bench Cleat 2 x 3 x 31-1/4" I* 1 32834-102 Center Post 4 x 4 x 67-1/8" (* Used only on gyms with gambrel tents) J 1 40400-100 Climbing Rope Assembly MODEL #SH304-10

© Copyright 2004, Creative Playthings, Printed in U.S.A.

PINNACLE ROCK WALL 19652-400 Rev F (05-20) Page 2 ASSEMBLY INSTRUCTIONS 1'-6 1/4" 1'-9 3/4" 1" The instructions on this page are for the installation of the Pinnacle Rock Wall to the back of a gym with a gambrel (barn-shaped) tent only. If your gym has a hooped tent or a wooden roof, these preparations are not necessary. Remove Wall Slats and Back Tent Post: If your gym is fully assembled, remove th

PINNACLE ROCK WALL

19652-400 Rev F (05-20) © Copyright 2004, Creative Playthings, Printed in U.S.A. Page 3 ASSEMBLY INSTRUCTIONS STEP 1 — Assemble Bench Step: Layout the two Bench Supports (G) so that they can be attached to each end of the Bench Cleat (H), lay the Bench Seat (F) on top and centered, see illustration. Fasten the two Bench Supports (G) to the Bench Cleat (H) using one #8 x 2-1/2" Phillips Head Screw to fasten each board. Fasten the Bench
© Copyright 2004, Creative Playthings, Printed in U.S.A. PINNACLE ROCK WALL 19652-400 Rev F (05-20) Page 4 ASSEMBLY INSTRUCTIONS 1/4" Typical Top Rope Board (E) #10 x 2-1/2" T25 Deck Screw 37-3/4" Rock Board Spacer Board Center Rail 5-1/2" 1-1/2" ideal Align Bottom View Center Rail STEP 5 — Attach Center Angled Rail: Attach the Center Rail (B) to the center of the back of the boards. Align the bottom of the Center Rail with the bottom of the two outside
PINNACLE ROCK WALL 19652-400 Rev F (05-20) © Copyright 2004, Creative Playthings, Printed in U.S.A. Page 5 ASSEMBLY INSTRUCTIONS STEP 6 — Remove Wall Slats: (Skybox installation only) The Pinnacle Rock Wall must be fastened to the rear of your Skybox. Create one opening, 22"-24" wide, in the rear wall of your Skybox by removing three Wall Slats (see illustration). Save the removed Wall Slats in case they are needed for repair or replacement. 22"
© Copyright 2004, Creative Playthings, Printed in U.S.A. PINNACLE ROCK WALL 19652-400 Rev F (05-20) Page 6 ASSEMBLY INSTRUCTIONS #10 x 2-1/2" T25 Deck Screw 1/4 x 4" Hex Bolt STEP 9 — Drill Rope Hole: Set the top Rope board in place, at the top of the Rock Wall. Mark the Wall or Platform Support in line with the large hole in the Top Rope Board. Remove the top Rope Board. Drill a 1" hole through the Support. STEP 10 — Fasten Top Rope Board: Use two 1/
PINNACLE ROCK WALL 19652-400 Rev F (05-20) © Copyright 2004, Creative Playthings, Printed in U.S.A. Page 7 ASSEMBLY INSTRUCTIONS Bottom Spacer Board Angled Rail Angled Rail Top Rope Board STEP 12 — Fasten Climbing Rope: The Climbing Rope Assembly comes pre-knotted on approximately 12" centers. This is done to prevent the rope from separating and provide a better grip. DO NOT MODIFY THE DESIGN OF THIS ROPE. IF THE ROPE IS REPLACED, IT IS EXTREMELY IMPORT
© Copyright 2004, Creative Playthings, Printed in U.S.A. PINNACLE ROCK WALL 19652-400 Rev F (05-20) Note: We have packaged more hardware than is required for assembly. Quantities listed are actual quantities required for assembly. Hardware Used on Premium Pine Rock Wall 40 17001-104 Weld Nut 1/4" 7 17001-105 Weld Nut 5/16" 40 12002-203 Flat Washer 8mm 7 12002-206 Flat Washer 5/16" 36 17003-609 Hex Bolt 1/4 x 1-1/2" 2 17003-1609 Bolt Hex 1/4 x 4" 6 17003-

Creative Playthings Play Sets & Playground Equipment Owners Instructions: