Anritsu MP1800A Installation Manual

Select [Ethernet] referring to Section 4.1 Selecting Remote Interface, and set IP address, subnet mask, and gateway address for the MP1800A. The controller must be connected to the MP1800A with the IP address and ports displayed here. Figure 4.2-1 IP address check For details about the setting restrictions, refer to “MX180000A Signal Quality Analyzer Control Software Remote Control Operation Manual”. Two connectors for 10 BASE-T/100 BASE-TX cables are provided on the rear panel. The two connectors are internally connected via a HUB, so they have ...

6-8 3. If MP1800A-x07 is installed, you will see the confirmation message shown in Figure 6.2-3. Click [Install] to continue the installation. Figure 6.2-3 Confirmation Dialog of USB Driver Installation (3) Note The screens shown in Figure 6.2-2 and Figure 6.2-3 may not be displayed on the front page. If software installations take a long time, check that these screens are is hidden at the back of the other screen. 4. The following window is displayed when the installation completes normally. Click [Finish] to end the installation procedure. Figure 6.2-4 Scre ...

2-11 2.5 Measures Against EOS and ESD This section describes how to prevent MP1800A from being damaged by electrical over-stress (EOS) or electrostatic discharge (ESD). 2.5.1 How to use the GND connection cable There is a risk of damaging MP1800A due to EOS if MP1800A and other peripheral equipment (including experimental circuits) are not connected to the common ground. When connecting MP1800A and other peripheral (including experimental circuits), connect other peripheral equipment to the ground terminal of MP1800A’s chassis with the GND connection cable be ...

The label shown on the left is attached to Anritsu products meeting our environmental standards. Details about this label and the environmental standards are available on the Anritsu website at https://www.anritsu.com ...

Model Name Recommended Module Model Name or Option Model Name/Part Name Max. Optical Output Power (mW)*1 Pulse Width (s)/Rep-etition Rate Emitted Wave- length (nm) Beam Divergence (deg) MU181600A G0174A 850 nm XFP module 0.78 CW 840-860 36.9 G0175A 1310 nm XFP module 0.8 CW 1290-1330 11.5 G0176A 1550 nm XFP module 1.58 CW 1530-1565 11.5 MU181601A G0177A 850 nm SFP module 0.56 CW 830-860 36.9 G0178A 1310 nm SFP module 1.0 CW 1270-1360 11.5 G0179A 1550 nm SFP module 1.0 CW 1430-1590 11.5 MU181620A Optionx01 1310nm Reference 5.0 CW 1290-13 ...

cleaning dust around the power supply and fan. - Clean the power inlet regularly. If dust accumulates around the power pins, there is a risk of fire. - Keep the cooling fan clean so that the ventilation holes are not obstructed. If the ventilation is obstructed, the cabinet may overheat and catch fire. • Never input a signal of more than the indicated value between the measured terminal and ground. Input of an excessive signal may damage the equipment. • This is a heavy object. When lifting and moving ...

Anritsu affixes the CE conformity marking on the following product(s) in accordance with the Decision 768/2008/EC to indicate that they conform to the EMC, LVD, and RoHS directive of the European Union (EU). CE marking 1. Product Model Model: MP1800A Signal Quality Analyzer 2. Applied Directive EMC: Directive 2014/30/EU LVD: Directive 2014/35/EU RoHS: Directive 2011/65/EU 3. Applied Standards • EMC: Emission: EN 61326-1: 2013 (Class A) Immunity: EN 61326-1: 2013 (Table 2) Performance Criteria* IEC 61000-4-2 (ESD) B IEC 61000-4-3 (EMF) A IEC 61000-4-4 (Burst) B IEC 6 ...