Draper Curved Onyx Assembly/mounting Instructions

Caution 1 Read instructions through completely before proceeding. 2 Follow instructions carefully. Installation contrary to instructions invalidates warranty. 3 Screen should be accessible for complete removal should fabric become damaged or should other service be required. 4 Screen should be installed level (using a carpenter’s level). 5 Nothing should be fastened to screen frame or viewing surface. 6 Make sure you have received all parts (see parts list below and exploded diagram on page 2). 7 Tools Required: Medium (#2) Phillips screwdriver (6" or greater shaft length suggested). Optional tools: Flat blade screwdriver or small putty knife. 8 Installer is responsible for providing appropriate hardware for mounting. 9 When lifting assembled screen, do not lift at only one corner; lift at both corners. Lifting by one corner could result in damage to the screen frame, especially on large screens. 10 The ideal temperature range for assembling folding screens to prevent damaging the surface is 68°-78° F (20°-26° C). Assembling below recommended temperatures may damage surface and void warranty. NOTE: Screen has been thoroughly inspected and tested at factory and found to be operating properly prior to shipment. Copyright © 2013 Draper Inc. Form CurvedOnyx_Inst13 Printed in U.S.A. ® If you encounter any difficulties installing or servicing your Onyx screen, call your dealer or Draper, Inc., Spiceland, Indiana, (765) 987-7999 or fax (765) 987-7142. Curved Onyx—Hardware and Parts List Frame Preparation 1 Clean area and place frame assembly pieces face down. Insert plastic corner pieces into ends of aluminum frame extrusions as indicated in Figures 1 through 4. Secure each corner to each frame extrusion by threading one #10-24 fastener through hole in plastic corner and into rounded slot in aluminum frame extrusion. Caution: Do not over-tighten fasteners—over-tightening could cause damage to the frame corners. Figure 1 2 Secure corner pieces to aluminum frame extrusions with four (4) remaining fasteners. Check to verify that all four (4) plastic corners are secure to aluminum frame extrusion lengths and all eight (8) fasteners are tight (see Fig. 5). Caution: Do not over-tighten fasteners—over-tightening could cause damage to the frame corners. Figure 2 Frame Extrusions - 4 #10-24 fasteners - 8 Viewing Surface - 1 Plastic Tubing - 4 Surface Retention Extrusions- varies Front Back Brackets - See last page of instructions Frame Corners - 4 Right-C173.042 Left-C173.043 Four-C098.018 Figure 3 Figure 5 Figure 4 (Continued on Page 2) Patented by Draper, Inc., U.S. Patent Nos. 6,785,047; 7,113,332; and 7,369,310. Caution: When lifting assembled screen, do not lift at only one corner; lift at both corners. Lifting by one corner could result in damage to the screen frame, especially on large screens.

Page 2 of 3 Figure 8 Mounting Screen to Wall 1 Determine height at which screen is to be mounted. Please Note: Top edge of screen frame will be located 1.5"above mounting bracket hole centerline when mounted to wall. 2 Mark hole centerline so that brackets can be mounted parallel and at equal height. 3 Install brackets so that the outermost edges are safely within the overall length of the aluminum frame extrusion to allow for minor horizontal screen adjustments. Installer is responsible for providing attachment hardware. 4 The bottom center bracket on the Curved Onyx acts as a locking bracket. Slide the center plate up, then push the screen back against the wall, releasing the center plate. The tongue on the center plate will then slide down into the frame extrusion, locking the frame in place. 5 Position screen slightly above brackets on wall. Surface to Frame Assembly 1 Return frame onto clean surface, face down, and drape completed surface assembly over completed frame profile with rounded edges of surface retention extrusions visible. 2 Hook surface retention extrusions on any side of surface to notch #2 on corresponding side of frame extrusion (see Fig. 8). Figure 10 6 Lower screen until it engages over brackets. Center screen horizontally on brackets as necessary. Please Note: Make sure screen is installed level. Figure 6 Surface Preparation 1 Move frame assembly out of the way, unroll viewing surface and place on smooth/clean surface. (Orient viewing surface so that folded side of hem is visible.) 2 Insert plastic tubing inside pocket formed by hem on all 4 edges of viewing surface (see Fig. 6). 3 Divide surface retention extrusions up so they will be evenly spaced all the way around the screen. 4 Carefully slide surface retention extrusions (rounded edge visible) along hem and onto surface on all 4 edges of fabric (see Fig. 7). Caution: Do not allow fabric to snag on ends of extrusions. If the screen fabric is not parallel with the surface retention extrusion, then it may slit and tear during installation. Figure 7 Plastic Tubing Surface Retention Extrusion Back of Viewing Surface Back of Viewing Surface Surface Retention Extrusion Fabric Attachment Extrusions Viewing Surface Notch #1 Notch #2 Notch #3 www.draperinc.com (765) 987-7999 Corner Reinforcement Kit (Part No. 253696) 1 If screen is being flown (suspended), or is 120" (viewing area) or larger in height or width, install Corner reinforcement Gussets to all four corners (see Fig. 9) Figure 9 Onyx Brackets Outer Brackets Center Brackets Top Bottom (locking) C264.049SA C501.324 C501.325 C501.326 Please Note: To make this step easier, pinch the end of the pocket closed before sliding it into the surface retention extrusions. 5 The top and bottom of the screen should have the ssame number of surface retention extrusions. The two sides should also have the same number. This will allow even spacing all the way around the screen. .6 Verify that all surface retention extrusions are installed with rounded edge visible and are centered on surface material. 3 Repeat on opposite side of surface, again using notch #2. 4 Repeat steps 2-3 with remaining edges of surface. 5 Ensure surface retention extrusions are centered lengthwise in tension slots on all 4 edges of surface. 6 If additional tension in certain areas of the screen is desired, adjust surface retention extrusions to notch #1 or #3 as necessary. Please Note: It is not necessary to adjust more than one edge at a time to increase surface tension.

15/8" 4" Curved Onyx Frame —Side Detail WALL TO EXT KIT REQUIRED < 1.125" None 1.125" - 1.875" C501.324 1.875" - 4.560" C501.325 >4.560" C501.326 See Placement Chart Overall Height minus 15/16" 2¼" Onyx Mounting Brackets Curved Onyx by Draper Page 3 of 3 www.draperinc.com (765) 987-7999 Onyx Nom. Image Overall Curve Outer Diag. Area Size Radius Kit Placement 16:9 HDTV Format 65" 31¾" x 56½" 39¾" x 64½" 40' C501.324 27¼" 73" 36" x 64" 44" x 72" 40' C501.324 31" 82" 40½" x 72" 48½" x 80" 40' C501.324 35" 92" 45" x 80" 53" x 88" 40' C501.325 39" 100" 49" x 87" 57" x 95" 40' C501.325 42½" 106" 52" x 92" 60" x 100" 40' C501.325 45" 110" 54" x 96" 62" x 104" 40' C501.325 47" 119" 58" x 104" 66" x 112" 40' C501.325 47½" 133" 65" x 116" 73" x 124" 40' C501.325 47½" 161" 80" x 140" 88" x 148" 40' C501.326 69" 193" 95" x 169" 103" x 177" 40' C501.326 83½" 220" 108" x 192" 116" x 200" 40' C501.326 87½" 4:3 NTSC Video Format 6' 43" x 57" 51" x 65" 40' C501.324 27½" 6' 6" 47" x 63" 55" x 71" 40' C501.324 30½" 7' 50" x 67" 58" x 75" 40' C501.324 32½" 7' 6" 54" x 72" 62" x 80" 40' C501.324 35" 100" 60" x 80" 68" x 88" 40' C501.325 39" 10' 72" x 96" 80" x 104" 40' C501.325 47" 150" 90" x 120" 98" x 128" 40' C501.325 47½" 15' 108" x 144" 116" x 152" 40' C501.326 71" 16:10 Format 67" 35¼" x 56½" 43¼" x 64½" 40' C501.324 27¼" 76" 40" x 64" 48" x 72" 40' C501.324 31" 85" 45" x 72" 53" x 80" 40' C501.324 35" 94" 50" x 80" 58" x 88" 40' C501.325 39" 109" 57½" x 92" 65½" x 100" 40' C501.325 45" 113" 60" x 96" 68" x 104" 40' C501.325 47" 123" 65" x 104" 73" x 112" 40' C501.325 47½" 137" 72½" x 116" 80½" x 124" 40' C501.325 47½" 165" 87½" x 140" 95½" x 148" 40' C501.326 69" 2.35:1 CinemaScope Format 115" 45" x 105¾" 53" x 113¾" 40' C501.325 47½" 132" 52" x 122" 60" x 130" 40' C501.325 47½" 148" 58" x 136¼" 66" x 144¼" 40' C501.326 671/8" 153" 60" x 141" 68" x 149" 40' C501.326 70" 166" 65" x 152¾" 73" x 160¾" 40' C501.326 793/8" 204" 80" x 188" 88" x 196" 40' C501.326 87½"