HP dc7900 - Convertible Minitower PC Illustrated Parts & Service Map

506593-002 page 1 Illustrated Parts & Service Map HP Compaq dc7900 Convertible Minitower Business PC © 2008, 2009 Hewlett-Packard Development Company, L.P. The information contained herein is subject to change without notice. HP shall not be liable for technical or editorial errors or omissions contained herein. Intel, Pentium, Intel Inside, and the Intel logo are trademarks or registered trademarks of the Intel Corporation and its subsidiaries in the U. S. and other countries. Document Number 506593-002. 2nd Edition March 2009. Key Specifications Spare Parts Processor Type Intel Celeron, Pentium Dual-Core, Core2 Duo, Core2 Quad RAM Type DDR2-SDRAM DIMMs, PC2-6400 (800 MHz) non-ECC Maximum RAM Supported 8 GB Expansion Slots • 2 PCIe-x16 • 1 PCIe-x1 • 3 PCI Graphics Adapter Integrated Intel GMA 3200 graphics Drive Support • 4 SATA (2 HDD + 2 Optical) • RAID 1 Support • floppy diskette drive, media card reader, removable hard disk drive, solid state drive Bays • 3 external 5.25-inch • 1 external 3.5-inch • 2 internal 3.5-inch I/O Interfaces Serial (2, 1 optional), parallel (optional), eSATA (optional), USB 2.0 (8), USB 2.0, internal on system board (2), RJ-45, front and rear audio jacks (2 each), PS/2 ports (2), VGA con- nector System Unit 1 Access panel 450713-001 2 Chassis not spared 3 5.25-inch bezel blank 335937-001 4 Power supply, 365W, 85% efficient 462434-001 4 Power supply, 365W 437799-001 5 Front bezel 450714-001 * Not shown Cables 1 Front USB, I/O assembly, power switch 450708-001 2 eSATA port assembly 497726-001 3 SATA cable, 18 inch, 1 straight end, 1 angled end 393958-001 4 SATA cable, 14 inch, 2 straight ends 391740-001 * Diskette drive cable 439216-001 * DVI cable 484156-001 * DMS-59 to dual VGA cable 463023-001 * Adapter, DVI to VGA 202997-001 *Not shown Keyboards (not illustrated) PS/2, Basic USB, Basic USB SmartCard 435302-xxx 435382-xxx 435385-xxx Arabic -171 LA Spanish -161 Belgian -181 Norwegian -091 BHCSY -B41 People’s Republic of China -AA1 Brazilian Portuguese -201 Portuguese -131 Czech -221 Romanian -271 Danish -081 Russian -251 Finnish -351 Saudi Arabia* -DE1 French -051 Slovakian -231 French Canadian -121 South Korea -KD1 German -041 Spanish -071 Greek -151 Swedish -101 Hebrew -BB1 Swiss -111 Hungarian -211 Taiwanese -AB1 International -B31 Thai -281 International English -L31 Turkish -141 Italian -061 U.S. -001 Japanese -291 U.K. -031 *For 435385-xxx only Mass Storage Devices (not illustrated) Diskette drive with bezel 431452-001 Media card reader, 5.25-inch 480033-001 Media card reader, 3.5-inch 507058-001 16X SATA DVD±RW and CD-RW drive with LightScribe 447310-001 16X SATA DVD-ROM drive 419496-001 500 GB SATA hard drive, 3.5-inch 504339-001 320 GB SATA hard drive, 3.5-inch 504338-001 250 GB SATA hard drive, 3.5-inch 504337-001 160 GB, 10000-RPM SATA hard drive, 2.5-inch with adapter 508312-001 160 GB SATA hard drive 504336-001 80 GB, 10000-RPM SATA hard drive, 2.5-inch with adapter 508311-001 80 GB, 7200-RPM SATA hard drive, 3.5-inch 449978-001

506593-002 page 2 Standard and Optional Boards System boards with thermal grease, alcohol pad, and CPU socket cover 1 System board 462431-001 1 System board, excludes ES/CS 490629-001 Memory modules (PC2-6400, CL6) 2 512 MB 418952-001 2 1 GB 418951-001 2 2 GB 457624-001 2 4 GB 497735-001 Other boards * Saffron WLAN 802.11a/b/g for use world-wide, includes bracket 498307-001 * Modem, PCIe, 56K, Agere International 56K, includes bracket 490689-001 * Modem, PCI, 56K, Agere International 398661-001 * ATI HD2400 (RV610) 256-MB graphics card, one DMS559 connector and one S-Video connector, low profile with ATX bracket 462477-001 * ATI HD3650 (RV635) 512-MB graphics card, two DP 1.1a connectors, one dual-link DVI connector, includes bracket 481421-001 * ATI HD3470 (RV620) 256-MB graphics card, one DP 1.1a connector, one dual-link DVI connector, includes bracket 483951-001 * Quadro NVS295 256-MB PCIe graphics card 519298-001 * HP nVidia Quadro NVS 290 256-MB graphics card, includes bracket 456137-001 * Broadcom NetXtreme Gbit Ethernet Plus NIC 488293-001 * NIC, GB, Intel PRO/1000, PCIe, full-height 398754-001 * Intel Gigabit NIC, includes bracket 490367-001 * 1394 card 2 external, 1 internal port 441448-001 Intel Celeron Processors with alcohol pad and thermal grease * 450, 2.2 GHz, 512-KB cache, single core 508256-001 * 440, 2.0 GHz, 512-KB cache, single core 449166-001 * E1500, 2.2 GHz, 512-MB cache, dual core 516899-001 * E1400, 2.0 GHz, 512-MB cache, dual core 491574-001 * E1200, 1.6 GHz, 512-MB cache, dual core 468589-001 Intel Pentium Dual Core Processors with alcohol pad and thermal grease * E5400, 2.7 GHz, 2-MB L2 cache 531989-001 * E5200, 2.5 GHz, 2-MB L2 cache 503382-001 * E2220, 2.4 GHz, 1-MB L2 cache 480714-001 * E2200, 2.2 GHz, 1-MB L2 cache 465216-001 Intel Core 2 Quad Processors with alcohol pad and thermal grease * Q9650, 3.00 GHz, 12-MB L2 cache 497734-001 * Q9550, 2.83 GHz, 12-MB L2 cache 465758-001 * Q9400, 2.66 GHz, 6-MB L2 cache 497733-001 * Q8300, 2.50 GHz, 4-MB L2 cache 516901-001 * Q8200, 2.33 GHz, 4-MB L2 cache 503381-001 Intel Core 2 Duo Processors with alcohol pad and thermal grease * E8600, 3.33 GHz, 6-MB L2 cache 497732-001 * E8500, 3.16 GHz, 6-MB L2 cache 466170-001 * E8400, 3.00 GHz, 6-MB L2 cache 509554-001 * E8300, 2.83 GHz, 6-MB L2 cache 466168-001 * E7500, 2.93 GHz, 3-MB L2 cache 531988-001 * E7400, 2.80 GHz, 3-MB L2 cache 508255-001 * E7300, 2.66 GHz, 3-MB L2 cache 500134-001 * E7200, 2.53 GHz, 3-MB L2 cache 490507-001 * E5300, 2.60 GHz, 2-MB L2 cache 516900-001 * Not shown Miscellaneous Parts 1 Fan holder, system fan 450710-001 2 Fan holder, CPU 450709-001 3 Chassis fan 450711-001 4 Fan, heatsink 455310-001 * Heatsink with alcohol pad and factory-applied thermal grease 490812-001 * Fan duct 450707-001 * Internal speaker 430129-001 * Hood sensor 392417-001 * Grommet, hard drive isolation 450712-001 * Solenoid lock 392416-001 * Mouse, PS2, optical 417966-001 * Mouse, optical 390938-001 * Mouse, laser 459821-001 * Printer port 497727-001 * 2nd serial port 392414-001 * Modem cable 198220-001 * Hard drive, removable carrier 444873-001 * Hard drive, removable frame 444872-001 *Not shown LP = Low profile FH = Full height Modem RJ-11 adapters (not illustrated) Austrian 417561-011 Italian 316904-065 Belgian 316904-181 Netherlands 316920-335 Czechoslovakian 234963-221 Polish 316904-241 French 316904-051 Saudi Arabian 316904-AR1 German 316904-045 Scandinavian 382848-DH1 Greek 316904-151 Swiss 417562-111 Hungarian 234963-215 Turkish 316904-141 Israel 316904-BB1 United Kingdom 158593-035

506593-002 page 3 System Board System Setup and Boot Basic system information regarding system information, setup, power management, hardware, and passwords is maintained in the Setup Utility held in the system ROM. The Setup Utility is accessed by pressing the F10 key when prompted (on screen) to do so during the boot sequence. If the screen prompt opportunity is missed, a restart will be necessary. For more information about Setup Utilities refer to the Service Reference Guide. System Board Connectors and Jumpers (component location may vary) E49 Password header P125 Hood sensor connector J9 RJ-45 over dual USB P126 Flying parallel port header J10 Quad stack USB P150 Media reader connector J20 PCI slot 1 P151 ReadyBoost connector J21 PCI slot 2 P23 Front audio connector J22 PCI slot 3 P24 Front USB connector J31 PCIe X1 P52 Second serial port J41 PCIe X16, slot 1 P60 SATA0 J42 PCIe X16, slot 2 P61 SATA1 J64 Display port connector P62 SATA2 J69 VGA connector P63 SATA3 J78 Double stack audio connector P64 SATA4 P1 Main power connector SW50 Clear CMOS button P3 CPU power connector XBT1 Real-time-clock battery socket P5 Power button/LED connector XMM1 DIMM 1 P6 Internal speaker connector XMM2 DIMM 2 P9 Front fan connector XMM3 DIMM 3 P10 Diskette drive connector XMM4 DIMM 4 P11 Rear fan connector XU1 Processor socket P124 Hood lock connector Computer Setup Menu Heading Option/Description File System Information - Lists the following main system specifications: • Product name • SKU number (some models) • Processor type/speed/stepping • Cache size (L1/L2) • Memory size/speed/channels • Integrated MAC Address • System BIOS • Chassis serial number • Asset tracking number • ME firmware version • Management node About - Displays copyright notice. Set Time and Date - Allows you to set system time and date. Flash System ROM - Allows you to select a drive containing a new BIOS. Replicated Setup - Save to Rmv Media and Restore from Rmv Media Default Setup • Save Current Settings as Default • Restore Factory Settings as Default Apply Defaults and Exit - Applies the selected default settings and clears any established passwords. Ignore Changes and Exit - Exits Computer setup without saving changes. Save Changes and Exit - Saves changes to system configuration or default settings and exits Computer Setup. Storage Device Configuration - Lists all installed BIOS-controlled storage devices. The following options are available: • Diskette Type(Legacy Diskettes only)-3.5” 1.44 MB and 5.25” 1.2 MB • Drive Emulation • Emulation Type - ATAPI Zip drive, hard disk, legacy diskette, CD-ROM drive, and ATAPI LS-120 drive • Multisector Transfers • Translation Mode • Translation Parameters • SATA Default Values Storage Options • Removable Media Boot • Legacy Diskette Write • SATA Emulation • Max eSATA Speed DPS Self-Test - Allows you to execute self-tests on ATA hard drives. Boot Order - Allows you to specify boot order. • Shortcut to Temporarily Override Boot Order Computer Setup Menu (Continued) Heading Option / Description Security Setup Password - Allows you to set and enable the setup (Administrator) password. Power-On Password - Allows you to set and enable power-on password. Password Options - When any password exists allows you to lock legacy resources, enable/disable network server mode, specify password require- ment for warm boot, and allows you to enable/disable Setup Browse Mode. Smart Cover (some models) - Allows you to lock/unlock cover lock and set status of cover removal sensor. Device Security (some models) - Enables/disables all I/O ports, audio, net- work controllers, SMBus controller, and embedded security devices. USB Security - Allows you to set Device Available/Device Hidden for front USB ports 3-6, rear USB ports 7-12, internal USB ports 1-2. Network Service Boot - Enables/disables boot from OS on a server. System IDs - Allows you to set Asset tag, ownership tag, Chassis serial number, UUID, and keyboard locale setting. DriveLock Security - Allows you to assign/modify a hard drive password for added security. System Security (some models) - Allows you to enable/disable: • Data Execution Prevention • Virtualization Technology • Virtualization Technology Directed I/O • Trusted Execution Technology • Embedded Security Device Support • OS management of Embedded Security Device through OS • Smart Card BIOS Password Support • PAVP (Protect Audio Video Path) (some models) Setup Security Level - Provides method to allow users limited access to change specified setup options without knowing Setup password. Power OS Power Management - Allows you to enable/disable Runtime Power Management, Idle Power Savings, ACPI S3 Hard Disk Reset, ACPI S3 PS2 Mouse Wakeup, USB Wake on Device Insertion (some models), Unique Sleep State Blink Rates. Hardware Power Management - Allows you to enable/disable SATA bus power management. Thermal - Allows you to control minimum permitted fan idle speed. Advanced Power-On Options - Allows you to set: • POST mode - QuickBoot, FullBoot, or FullBoot every 1-30 days. • POST messages - Enable/disable • MEBx Setup prompt - Enable/disable or hidden/displayed • F9 prompt - Enable/disable • F10 prompt - Enable/disable • F12 prompt - Enable/disable • Factory Recovery Boot Support - Enable/disable • Option ROM prompt - Enable/disable • WOL After Power Loss - Enable/disable • Remote wakeup boot source - Remote server/local hard drive • After Power Loss - Off/on/previous state • POST delay - None, 5, 10, 15, or 20 seconds • Limit CPUID Maximum value to 3 Execute Memory Test (some models) -Restarts computer and executes POST memory test. BIOS Power-On - Allows you to set the computer to turn on at a preset time. Onboard Devices - Allows you to set resources or disable onboard system devices. PCI Devices - Lists installed PCI devices with their IRQ settings and allows you to reconfigure IRQ or disable devices. PCI VGA Configuration - Allows you to specify which VGA controller will be used when multiple video adapters are available. Bus Options (some models) - Allows you to enable/disable PCI SERR# Generation and PCI VGA palette snooping. Device Options - Allows you to set: • Printer Mode - Bi-Directional, EPP & ECP, Output Only • Num Lock state at power-on - off/on • S5 Wake on LAN - enable/disable • Processor cache - enable/disable • Integrated video - enable/disable • Multi-Processor - enable/disable • Internal speaker - enable/disable • Monitor Tracking - enable/disable • NIC PXE Option ROM Download - enable/disable Management Devices - Only displayed in Advanced menu when BIOS detects multiple management options. Management Operations - Allows you to set: • MEBx Setup Prompt - enable/disable • Remote Help Prompt - enable/disable • Remote Help Lockout - enable/disable • Remote Help Connection Timeout - 5, 10, 15, 20, 30, 40, 50, 60, 120, 180, 240 seconds • SOL Character Echo - enable/disable • SOL Terminal Emulation Mode - enable/disable • SOL Keyboard (enable/disable System Hardware Interrupts IRQ System Function IRQ System Function 0 Timer Interrupt 8 Real-Time Clock 1 Keyboard 9 Unused 2 Interrupt Controller Cascade 10 Unused, available for PCI 3 Serial Port (COM B) 11 Unused, available for PCI 4 Serial Port (COM A) 12 Mouse 5 Unused, available for PCI 13 Coprocessor 6 Diskette Drive 14 Primary ATA (IDE) Controller 7 Parallel Port (LPT 1) 15 Secondary ATA (IDE) Controller

506593-002 page 4 Failsafe Boot Block ROM The computer comes with a reprogrammable flash system ROM (read only memory). To upgrade the ROM, download the latest ROM BIOS image from the HP Web site (www.hp.com) and follow the online GUI/instructions. Your system ROM includes a Failsafe Boot Block that is protected during the flash process and allows the computer to be restarted in the unlikely event of an unsuccessful ROM flash. If the system detects an invalid system ROM during the boot sequence, the Failsafe Boot Block attempts to locate a valid BIOS image on removable media. To recover from the Boot Block recovery mode complete the following steps: Boot Block Recovery 1. Remove any bootable media from the computer and turn off power. 2. Insert a flash drive or CD containing the ROM BIOS in the root directory. The media must be formatted using the FAT12, FAT16, or FAT32 file system. 3. Turn on power to the system. 4. The system will automatically flash the ROM. NOTE: BitLocker prevents Windows Vista from booting when a CD containing the BIOS image file is in an optical drive. If BitLocker is enabled, remove this CD before attempting to boot to Windows Vista. Password Security Establishing a Setup or Power-On password: 1. Turn on or restart the computer. If you are in Windows, click Start > Shut Down >Restart. 2. As soon as the computer is turned on, press F10 when the monitor light turns green to enter Computer Setup. Press Enter to bypass the title screen, if necessary. If you do not press F10 when prompted, a restart will be necessary. 3. To establish a Setup password, select Security > Setup Password and follow the instructions on the screen. - or - To establish a Power-On password, select Security > Power-On Password and follow the instructions on the screen 4. Before exiting, click File > Save Changes and Exit. Changing a Setup or Power-On password: 1. Turn on or restart the computer. If you are in Windows, click Start > Shut Down > Restart. To change the Setup password, go to step 2. To change the Power-on password, go to step 3. 2. To change the Setup password, as soon as the computer is turned on, press F10 when the monitor light turns green to enter Computer Setup. Press Enter to bypass the title screen, if necessary. 3. When the key icon appears, type your current password, a slash (/) or alternate delimiter character, your new password, another slash (/) or alternate delimiter character, and your new password again as shown: current password/new password/new password. NOTE: Type the new password carefully since the characters do not appear on the screen. 4. Press Enter. The new password will take effect the next time the computer is restarted. Deleting a Power-On or Setup password 1. Turn on or restart the computer. If you are in Windows, click Start > Shut Down > Restart. To delete the Setup password, go to step 2. To delete the Power-On password, go to step 3. 2. To change the Setup password, as soon as the computer is turned on, press F10 when the monitor light turns green to enter Computer Setup. Press Enter to bypass the title screen, if necessary. 3. When the key icon appears, type your current password followed by a slash (/) or alternate delimiter character as shown. Example: currentpassword/ 4. Press Enter. Security Features Diagnostic Functions Diagnostic functions are provided by the Setup Utility (in system ROM) and by HP Insight Diagnostics. HP Insight Diagnostics provides detailed system information including: • Processor type and speed • Memory amount, mapping, and integrity • Hardware peripheral availability/settings • Hard drive type, space used/available • System identification, asset tracking Insight Diagnostics may be found on the Documentation and Diagnostics CD that shipped with the computer. The tool may also be downloaded from the HP Web site using the following pro- cedure: 1. Go to www.hp.com 2. Click the Software & Download driver link. 3. Enter the product number (for example, dc7900) in the text box and press the Enter key. 4. Select the specific product. 5. Select the OS. 6. Click the Diagnostics link. 7. Select HP Insight Diagnostics Offline Edition. 8. Click Download. NOTE: The download includes instructions on how to create a bootable CD. Clearing CMOS 1. Turn off the computer and any external devices, and disconnect the power cord from the power outlet. 2. Remove the chassis access panel. 3. On the system board, press and hold the CMOS button for 5 seconds. 4. Replace the chassis access panel and reconnect the power cord. 5. Turn on the computer and allow it to start. Error Conditions and Messages Feature Purpose How It Is Established Floppy drive controller Prevents the transfer of data to or from the floppy drive. Setup Utilities Device Boot Disabling Prevents booting from and or all of these devices: Internal or external USB, Internal ODD, or Internal FDD Setup Utilities Security Option Prevents use of computer until password is entered. Can apply to both initial startup and restart. Setup Utilities BIOS Write Protect Restricts ability to change ROM BIOS with- out approval. Setup Utilities. USB Controller Allows you to disable or enable all USB devices. Setup Utilities Diagnostic LEDs LED Color LED Activity State/Message Power Green On Computer on Power Green 1 blink every 2 seconds Normal Suspend Mode Power Red 1 blink every second followed by a 2 second pause CPU thermal shutdown Power Red 3 blinks, 1 blink every second followed by a 2 second pause Processor not installed Power Red 4 blinks, 1 blink every second followed by a 2 second pause Power failure (power supply overload) Power Red 5 blinks, 1 blink every second followed by a 2 second pause Pre-video memory error Power Red 6 blinks, 1 blink every second followed by a 2 second pause Pre-video graphics error Power Red 7 blinks, 1 blink every second followed by a 2 second pause System board failure (ROM Power Red 8 blinks, 1 blink every second followed by a 2 second pause Invalid ROM based on Checksum Power Red 9 blinks, 1 blink every second followed by a 2 second pause System powers on but is unable to boot Power Red 10 blinks, 1 blink every second followed by a 2 second pause Bad option card Power Red 11 blinks, 1 blink every second followed by a 2 second pause The current processor does not support a feature previously enabled on this system. none none System does not power on and LEDs are not flashing System unable to power on Common POST Error Messages Screen Message Probable Cause Recommended Action 101-Option ROM Error 1. System ROM checksum error. 2. Expansion board option ROM checksum 1. Verify ROM, reflash if required 2. Remove suspected card, reboot 3. Clear CMOS memory, reboot 4. Replace system board 103-System Board Failure DMA, timers 1. Clear CMOS memory. 2. Remove expansion boards. 3. Replace system board. 164-Memory Size Error and 201-Memory Error Incorrect memory configu- ration 1. Run Setup (F10). 2. Check DIMMs for proper seating, type, and HP compatibility. 3. Remove DIMMs singularly and reboot to isolate faulty DIMM. 4. Replace system board. 214-DIMM Configura- tion Warning Populated DIMM configura- tion is not optimized Rearrange the DIMMs so that each channel has the same amount of memory. 301-, 304-Keyboard error Keyboard failure. Check keyboard connection or keys. Check connector for bent of missing pins. Replace keyboard. If 304, possible system board prob- lem. 501-Display Adapter Failure Graphics display controller. 1. Reseat graphics card. 2. Clear CMOS. 3. Check monitor connection. 4. Replace graphics card. 1720-SMART Hard Drive Detects Imminent Failure Hard drive is about to fail. 1. Determine if hard drive is giving correct error message. Enter Computer Setup and run the Drive Protection System test under Storage > DPS Self- test. 2. Apply hard drive firmware patch if applicable. 3. Back up contents and replace hard drive. 1796-SATA Cabling Error One or more SATA devices are improperly attached. For optimal performance, the SATA 0 and SATA 1 con- nectors must be used before SATA 2 and SATA 3. Ensure SATA connectors are used in ascending order. For one device, use SATA 0. For two devices, use SATA 0 and SATA 1. For three devices, use SATA 0, SATA1, and SATA 2. 1801-Microcode Patch Error Processor not supported by ROM BIOS. 1. Upgrade BIOS to proper version. 2. Change the processor.