Forza ALU110 Instruction

Text of Forza ALU110 Instruction

FREESTANDING BOX GOAL

www.networldsports.co.uk // +44 (0) 1691 683 807 // [email protected] www.networldsports.com // 1-866-861-9095 // [email protected] @NetWorldSports

Crossbar Connector Front & Back (2x)

Straight Bracket (4x) 38027 37879 Sidebar/Upright (4x) 38033 Corner Bracket (2x) 38038 L Bracket (2x) Upright Corner Joint (2x) Crossbar/Backbar (4x) 38044 Upright Support (2x) Corner Joint (4x) 38016 38022 M8 Spring Washers (16x) 38099 M8x20 Hex Bolt (16x) 38071 M10x25 Bolt (8x) 38055 M10x20 Bolt (54x) 38049 M10 Washer (62x) 38088 M8 Washer (10x) 38094 M10 Lock Nut (62x) 38077 M8 Lock Nut (5x) 38

Ratchet with Sockets

Rubber Mallet 38122 Allen Key Weights Wheels 1. Read through the instruction thoroughly before assembling the goal. 2. Check parts for any defects prior to the assembly of the goal. 3. Ensure due diligence is carried out and a risk assessment followed prior to the assembly of the goal. 4. Safety/warning stickers must be visible at all times. 5. Goal must be anchored at all times. 6. Ne

STEP 1 - Crossbar/Backbar (Fig. 1)

Fig.1 Layout the crossbar sections and backbar sections (37906) and connector (37934). Slide 2x M10x20 bolts (38049) into each crossbar section and locate between the 2 pre-drilled holes. (fig.1). On the backbar slide 3x M10 bolts (38049) into both backbar sections (37906) locating 2 bolts between the 2 pre-drilled holes and 1 in the centre of the section. See (fig.2). Slot the connector (37934) into the crossb

STEP 4 - Fixing Crossbar to Uprights (Fig. 4)

STEP 5 - Attach Backbar to Sidebar (Fig. 5) Locate the corner bracket (38033) over the pre-positioned bolts. Place M10 washers (38088) over M10x20 bolts as per diagram (fig.4a). Secure in place using M10 nuts (38077). Repeat for other side. ATTENTION - ensure all joints are butted up to each other before tightening. STEP 6 - Fixing Backbar to Sidebar (Fig. 6) Plac

STEP 8 - Fixing uprights to base (Fig. 8)

Locate the L bracket (38038) over the pre-positioned bolts. Place M10 washers (38088) over bolts and secure in place with M10 nuts (38077). Locate the upright support (38044) over bolts. Place M10 washers (38088) over bolts and secure with M10 nuts (38077) Repeat step 8 to secure other side. ATTENTION – ensure all joints are butted up to each other before tightening. ATTENTION, WHEELS – PLEASE NOTE! If wheel

Step 9 – Fitting and securing back stanchion

to base (fig.9, fig.9a, fig.9b & fig.9c) Slide back stanchion (39013) onto stanchion socket (39017) see diagram (fig.9.) Slide 2x M10x25 bolts (38055) down back stanchion to locate in the slots of the stanchion support. Locate upright support (39021) on pre-positioned bolts and place M10 washers (38088) over bolts and secure with M10 nuts (38077) see diagram (Fig.9a) Locate stanchion brace (39057) on p

Step 10 – Fitting and securing ratchet (fig.10 & fig.10a)

Slide 2x M10x20 bolts (38049) into back stanchion. Locate ratchet (39125) over the 2 bolts. Place M10 washers (38088) over bolts and secure in place with M10 nuts (38077) approximately 120cm from the top of the stanchion. Repeat step 10 for the other side. Fig.10 Fig.10a 39125 38088 38077 Step 11 – Fitting and securing stanchion support (fig.11, fig.11b. fig.11c & fig.11d) Slide 1x M10x

Step 12 – Fitting and securing stanchion

D-ring (fig.12 & fig.12a) Slide 2x M10x20 bolts (38049) into the back stanchion. Locate the stanchion D-ring (39145) over the M10 bolts at the top of the stanchion see diagram (fig.12) Add the cap (39149) to the top of the back stanchion. Place M10 washers (38088) over the bolts and secure with M10 nuts (38077) see diagram (fig.12a) Fig.12 Fig.12a 39145 39077 Fig.11b Fig.11c 39149

Step 13 - Assemble and fit net support

(fig.13, fig.13a & 13b) Slide net support (39081) into net support (39085) ensuring both ends are facing the same way. Place 1x M8 washer (39081) over 1x M8x45 bolt and locate the bolt through the pre-drilled hole and secure with 1x M8 washer (39081) and nut (38082). Place 1x M8 washer (38094) over 4x M8x45 bolts (38064) and locate through pre-drilled holes in the net support. Locate net support brackets (39121)

Step 14 – Net. (Fig.14, fig.14a, & fig.14b)

Place the net over the frame, noting that the red tabs denote the top corners of the net as per (fig.14.) Attach the net using push and twist clips (38174) as per fig.14a. Use push and twist brackets (39137) for the top corners of the goal as per fig.14b. Fix net in place over brackets using twist brackets (39137) as per fig.14c. Fig.14 Fig.14a Fig.14c Fig.14b

Step 15 – Tensioning net. (Fig.15, fig.15a & fig.15b)

Take ratchet strap (39129) and clip to the back corner of the net, Thread the end through the stanchion D-ring and the ratchet. Take ratchet strap (39133) and clip it to the net at the same height as the corner, in line with the centre of the crossbar straight bracket. Thread the end through the stanchion D-ring and the ratchet. Repeat this for the other side. Use ratchet to tension net to the r

Ensure M10x25 Bolts (38055) have been slotted into place

whilst constructing the goal. Place the Wheel Bracket over the prepositioned bolts. Fix in place with 2x M10 Washer (38088) and 2x M10 Nuts (38077). Ensure Wheels are fixed on the correct side of the goal. When the wheels are not in use the handles must be facng away from the pitch. Fig.16 Fig.17 Fig.17a 38077 38088 Fill Weights with sand or water to the desired weight. Sl

Forza Sports & Outdoors Owners Instructions: