Comtech EF Data KPA-020IN Installation And Operation Manual

Text of Comtech EF Data KPA-020IN Installation And Operation Manual

Ku-Band Solid-State Power Amplifier

KPA-020IN, KPA-040, KPA-080, KPA-100 Installation and Operation Manual IMPORTANT NOTE: The information contained in this document supercedes all previously published information regarding this product. Product specifications are subject to change without prior notice. Part Number MN/KPA.IOM Revision 0

Copyright © Comtech EF Data, 2000. All rights reserved. Printed in the USA.

Comtech EF Data, 2114 West 7th Street, Tempe, Arizona 85281 USA, 480.333.2200, FAX: 480.333.2161. KPA Ku-Band Solid-State Power Amplifier KPA-020IN, KPA-040, KPA-080, KPA-100 Installation and Operation Manual Part Number MN/KPA.IOM Revision 0 September 30, 2005 Comtech EF Data is an ISO 9001 Registered Company.

Contact the Comtech EF Data Customer Support Department for:

• Product support or training • Information on upgrading or returning a product • Reporting comments or suggestions concerning manuals A Customer Support representative may be reached at: Comtech EF Data Attention: Customer Support Department 2114 West 7th Street Tempe, Arizona 85281 USA 480.333.2200 (Main Comtech EF Data Number) 480.333.4357 (Customer Support Desk) 480.

Table of Contents

CHAPTER 1. INTRODUCTION............................................................................................................1-1 1.1 Overview .................................................................................................................................................... 1-1 1.2 Functional Description....................................................................................................
Ku-Band Solid-State Power Amplifier Revision 0 Preface MN/KPA.IOM iv CHAPTER 4. OPERATION..................................................................................................................4-1 4.1 General....................................................................................................................................................... 4-1 4.1.1 Front Panel ....................................................................
Ku-Band Solid-State Power Amplifier Revision 0 Preface MN/KPA.IOM v 6.8 Confirmation Response............................................................................................................................. 6-7 6.8.1 Error Response............................................................................................................................................ 6-7 6.8.2 End of Message....................................................
Ku-Band Solid-State Power Amplifier Revision 0 Preface MN/KPA.IOM vi Figures Figure 1-1. Family of Ku-Band Solid-State High Power Amplifiers ....................................................................... 1-1 Figure 1-2. Block Diagram of KPA-020IN .............................................................................................................. 1-2 Figure 1-2. Block Diagram of KPA-040 .................................................
Ku-Band Solid-State Power Amplifier Revision 0 Preface MN/KPA.IOM vii About this Manual This manual provides installation and operation information for the Comtech EF Data Ku-Band Solid-State Power Amplifier, KPA-020IN, KPS-040, KPA080, and KPA100. This is a technical document intended for earth station engineers, technicians, and operators responsible for the operation and maintenance of the KPA. Conventions and References Cautions and Warnings CAUTION C
Ku-Band Solid-State Power Amplifier Revision 0 Preface MN/KPA.IOM viii Metric Conversion Metric conversion information is located on the inside back cover of this manual. This information is provided to assist the operator in cross-referencing Non-Metric to Metric conversions. Military Standards References to “MIL-STD-188” apply to the 114A series (i.e., MIL-STD-188-114A), which provides electrical and functional characteristics of the unbalanced and b
Ku-Band Solid-State Power Amplifier Revision 0 Preface MN/KPA.IOM ix European EMC Directive In order to meet the European Electro-Magnetic Compatibility (EMC) Directive (EN55022, EN50082-1), properly shielded cables for DATA I/O are required. More specifically, these cables must be shielded from end-to-end, ensuring a continuous ground shield. The following information is applicable for the European Low Voltage Directive (EN60950): Type of power cord
Ku-Band Solid-State Power Amplifier Revision 0 Preface MN/KPA.IOM x Warranty Policy This Comtech EF Data product is warranted against defects in material and workmanship for a period of 2 years from the date of shipment. During the warranty period, Comtech EF Data will, at its option, repair or replace products that prove to be defective. For equipment under warranty, the customer is responsible for freight to Comtech EF Data and all related custom, taxes,

Chapter 1. Introduction

1.1 Overview The Ku-Band Solid-State High Power Amplifier (KPA) is designed for use in communication systems, or in satellite up-link data systems. The KPA (Figure 1-1) operates over the RF input frequency range of 14.0 to 14.5 GHZ. 1.2 Functional Description The KPA is designed to be hard mounted in a standard 19-inch (48 cm) rack or cabinet, or to be rack mounted using Comtech EF Data slide mechanisms provided with the SSPA to
Ku-Band Solid-State Power Amplifier Revision 0 Introduction MN/KPA.IOM 1-2 Each unit has the ability to function as a 1+1 or 1+2 redundancy controller in the backup mode. The optional redundancy configuration is implemented by attaching a ganged Waveguide/coax transfer switch (es) to input and output connectors of the amplifiers with a combination coaxial cable and Waveguide kit. When the backup KPA is commanded into the controller mode, it monitors the on
Ku-Band Solid-State Power Amplifier Revision 0 Introduction MN/KPA.IOM 1-3 Figure 1-2. Block Diagram of KPA-020IN

Comtech EF Data Amplifier Owners Instructions: