EFILive CM2350B Operation & User’s Manual

All other trademarks belong to their respective owners. Cummins 6.7L CM2350B CSP5 User Guide © 1998 EFILive Limited All rights reserved First published 6 May 2015 Revised 6 April 2021

[email protected] - 1 - www.efilive.com Contents ............................................................................................................ 4 Prerequisites .................................................................................................................... 4 Intended Audience ....................................................................................................... 4 Computer Knowledge ................................................................................................... 4 Tuning Knowledge ....................................................................................................... 4 ...................................................................................................... 5 Introduction ...................................................................................................................... 5 What is EFILive? .......................................................................................................... 5 What is EFILive CSP5? ................................................................................................ 5 Software Version Overview .......................................................................................... 6 ............................................................................................................... 7 CSP5 Upgrade ................................................................................................................. 7 CSP5 Upgrade Checklist .............................................................................................. 7 Upgrade Operating System to CSP5 ............................................................................ 7 Tune Switch Password ................................................................................................. 9 CSP5 CAN Tunes ....................................................................................................... 10 Supported Switching Methods ................................................................................... 10 .......................................................................................................... 11 V8 Scan and Tune Scan ................................................................................................ 11 Pass-Thru Data Logging ............................................................................................ 11

[email protected] - 2 - www.efilive.com Pass-Thru Licence and Flash a Controller ................................................................. 12 .......................................................................................................... 14 Configure FlashScan/AutoCal for BBX .......................................................................... 14 EDA Data Logging ..................................................................................................... 14 Configure Tuning ........................................................................................................ 15 Tune File Switching .................................................................................................... 15 Configure DTCs ......................................................................................................... 15 Quick Setup ............................................................................................................... 15 ............................................................................................................. 17 FlashScan Menu Navigation .......................................................................................... 17 FlashScan/AutoCal V3 ............................................................................................... 17 Data Logging .......................................................................................................... 17 License and Flash a Controller ............................................................................... 17 Switch Tunes using FlashScan/AutoCal V3 ........................................................... 18 FlashScan V2 ............................................................................................................. 18 Data Logging .......................................................................................................... 18 License and Flash a Controller ............................................................................... 19 Switch Tunes using FlashScan V2 ......................................................................... 20 ............................................................................................................. 21 Support .......................................................................................................................... 21 Trouble Shooting ........................................................................................................ 21 Error Codes ................................................................................................................ 21 Test for Rogue Modules ............................................................................................. 21 Trace Files ................................................................................................................. 21 V8 Scan and Tune *.htx files .................................................................................. 21 FlashScan/AutoCal V3 *.xalm files ......................................................................... 22

[email protected] - 3 - www.efilive.com FlashScan V2 Trace Files ...................................................................................... 22 Knowledgebase.......................................................................................................... 22 EFILive Authorized Dealer ......................................................................................... 23 How to Tune? ............................................................................................................. 23 EFILive Service Desk ................................................................................................. 23

[email protected] - 4 - www.efilive.com Prerequisites Intended Audience EFILive Customers using the V8 Scan and Tune Tool software. Computer Knowledge It is expected that readers have a basic understanding of:  The Windows operating system;  Starting and using Windows applications;  Navigating folders using Windows Explorer. Tuning Knowledge It is expected that readers have a basic understanding of:  Electronic Fuel Injection;  On Board Diagnostics.

[email protected] - 5 - www.efilive.com Introduction What is EFILive? EFILive is tuning software and hardware - it is not a tune. Together the software and hardware give users the tools to write tunes. EFILive does not provide tune files, tuning advice or support, but do provide software support and hardware support. What is EFILive CSP5? EFILive's CSP5 custom operating systems for Cummins controllers allows customers to be able to switch 'on the fly' between multiple tunes, all stored in the ECM's flash memory. Historically, Cummins Switchable Programming had 5 tune positions; however as supported Cummins platforms have expanded this no longer holds true. ECM memory now defines the number of tunes that are available for switching for each ECM type as per the table below. CSP Controller Matrix CMB (CM849) 2006-2007 5.9L CSP5 5 tunes accessible through CAN bus switching, and a 6th tune that is switched using an input on one of the ECM connectors. CMC (CM2100A) 2007-2009 6.7L CSP5 CMD (CM2200) Pick Up Trucks 2010-2012 6.7L CSP5 5 Tunes accessible through CAN bus switching. CMD (CM2200) Cab & Chassis 2010-2012 6.7L CSP2 2 tunes accessible through CAN bus switching. CME (CM2350B) 2013-2018 6.7L CSP4 4 tunes accessible through CAN bus switching. CMF (CM2450B) 2019+ 6.7L CSP5 5 tunes accessible through CAN bus switching. Whilst different controllers contain different numbers of tunes, collectively this feature is still referred to as CSP5. Having multiple tunes instantly accessible means changing tunes to suit different driving conditions no longer requires the ECM to be reflashed each time you choose to run a different tune. (E.g. racing, towing, or power limiting.) Simply build multiple tunes to fill the CSP5 slots, flash the ECM once and then select your desired tune through your EFILive hardware (or other approved switching devices) at any time. CSP5 delivers scanning enhancements to customers via Enhanced Data Acquisition (EDA). EDA, EFILive’s custom scanning mode is the first of its kind and aims to simplify the task of information sharing between users as every individual data parameter has been selected with tuning feedback in mind. EDA allows customers to log 45 individual data parameters specifically chosen to

[email protected] - 6 - www.efilive.com complement tuning at up to 50 frames per second for V8 BBL & V7.5 pass through logging. EDA scanning is only available on CSP5 upgraded ECM's. Software Version Overview This version of the Cummins 6.7L CM2350B CSP5 User Guide migrates all processes to EFILive V8 Scan and Tune software. Functionality is still available in V7.5 software, however software support and bug fixes will cease in 2021. FlashScan/AutoCal V3 and AutoCal V2 are not compatible with V7 software. V7 functions are only supported by FlashScan V2. The following is a brief view of the activities that are performed with the different software versions: Feature V7 V8 Scanning OBDII Diagnostics Reading Flashing Tune Editing VIN License Management Firmware Management

[email protected] - 7 - www.efilive.com CSP5 Upgrade CSP5 Upgrade Checklist CSP5 upgrades are only available on specific factory operating systems. Typically these are based on the latest factory update (at time of development). If you have a truck that has an OS not listed below, you will need to upgrade your base file first. Supported CSP5 operating systems are listed in the table below. These were the latest factory updates as of early 2018; released 7 years after this ECM type was introduced. EFILive will not be offering CSP on older, obscure or obsolete OS's. No further EFILive development is scheduled for the Dodge Cummins CME platform. CSP4 Operating System - Pickup 32130601 32150101 32180100 32130902 32150102 32180101 32140204 32150200 33140100 32140305 32160202 34140100 32140602 32170403 32150101 32170404 CSP4 Operating System - Cab & Chassis 31130501 51140302 51150102 Where a vehicle has been previously tuned with a product other than EFILive, the conversion process may fail and render the ECM non-functional and not recoverable. EFILive recommends users source a good known base file for CSP5. To upgrade to CSP5 exclusively in EFILive V8 Scan and Tune software you must be running the following (or higher) software versions. 1. EFILive V8.3.5 or later. 2. FlashScan V3 / AutoCal V3 Firmware – V3.00.060. 3. FlashScan V2 / AutoCal V2 Firmware - V2.08.170. The latest software versions are available for download from EFILive's website. Upgrade Operating System to CSP5 1. Open V8 Scan and Tune software and your stock tune file. 2. Navigate to [F5: Edit].

[email protected] - 8 - www.efilive.com 3. Expand the Internal Flash -> Operating System Patches Folder and select CSP5 v1.00 Custom Operating System. 4. Select the [Apply Upgrade] button. 5. Select [Yes] to the “This operation cannot be undone, continue?” dialog box. 6. A message indicating “Upgrade applied successfully.” will now display. 7. Save the file with a new name using, File > Save As. Maybe something like... 'My Truck Base CSP5 Conversion.ctz’. 8. Close the tune file. 9. On the EFILive V8 Scan and Tune Recent Items list you will see your stock tune and your upgraded CSP5 tune. Confirm that the operating system number on the base file is different to the upgraded CSP5 converted file. 10. Reopen the tune file that was converted.

[email protected] - 9 - www.efilive.com 11. Navigate to [F5: Edit] and expand the EFILive Custom Calibrations folder. 12. EFILive automatically populates the new CSP5 tables with factory values during the upgrade. On modified engines these may not be suitable settings, so you may need to copy your own tables in to the new CSP5 section(s). Program #1 to Program #3 have factory values inserted into the maps. Program #4 contains the values from the standard OS maps prior to the CSP5 conversion. 13. Edit the values on your individual tunes, and [Save] the changes to your tune file. 14. Flash the CSP5 tune into your ECM. Refer to pass-thru flashing, FlashScan V3/AutoCal V3 flashing or FlashScan V2 flashing for further instructions. Tune Switch Password Users may restrict tune selection by adding a password to move between tune selections to prevent unauthorized switching between tunes 1 to 5. Before switching between tune selections, users would need to enter in the password (1 to 9999). If the password is correct, the tune will switch, if it is incorrect the tune will not switch. It should be noted that not all switching devices may support this function, however EFILive's own FlashScan and AutoCal hardware does. To enable the tune switch password, users need to input their chosen password in the calibration. As the calibration description states, if the password = 0 then there is no password prompt given to the user when switching tunes.

[email protected] - 10 - www.efilive.com CSP5 CAN Tunes The CSP5 tunes labelled "Program #1 to Program #4" are all switched via a device on the CAN bus. NOTE: Whenever the ECM is reflashed tune switching will default to using CSP5 Program #4 unless the Default CSP Tune After Reflash parameter is set. Supported Switching Methods EFILive’s CSP5 custom operating system can be switched using EFILive FlashScan/AutoCal V3, FlashScan/AutoCal V2, and the SoCal Diesel CSP5 switch and the Starlite Diesel StarLog. EFILive recommends that customers confirm that their chosen integration product is approved for use. To setup an approved integration product, users should: 1. Convert their base file to a CSP5 operating system, as described in this document. 2. Edit tune parameters as necessary and save the file. 3. Flash their modified file into their ECM using the V8 Scan and Tune application as described in this document. (Specific selection of 3rd party product is NOT required in tune file). 4. Setup the 3rd party device as per the manufacturer’s instructions.

[email protected] - 11 - www.efilive.com V8 Scan and Tune Scan Pass-Thru Data Logging To log data using FlashScan or AutoCal and V8 Scan and Tune software; 1. Open the EFILive V8 Scan and Tune. 2. Connect your FlashScan/AutoCal device to your PC and vehicle. 3. Turn the vehicle ignition to the On position 4. Select an existing Dashboard configuration either by using the [Open Dash] button or using the Dashboard drop down, or configure after making controller and PID selections. 5. Navigate to the [F2: Scan] -> [F2: PIDs] menu option. 6. In the Engine field use the drop down list to select the CME controller type or use Auto Detect. 7. Drag the EDA 1 PID folder from the Available PIDs window into the Selected PIDs window. 8. Navigate to the [F3: Data], [F4: Charts], [F5: Gauges] or [F6: Maps] tab and configure your dashboard to arrange data displays where a dashboard has not already been selected. 9. Users should [Save Dash] to save their custom configurations to reduce future configuration requirements. 10. Start the vehicle. 11. Select either Record or Monitor from the [F3: Data], [F4: Charts], [F5: Gauges] or [F6: Maps] screens. 12. Stop the vehicle and turn the ignition off prior to selecting Stop to stop the data logging session. 13. Save the log.

[email protected] - 12 - www.efilive.com 14. To replay the data log, navigate to the [F3: Data], [F4: Charts], [F5: Gauges] or [F6: Maps] tab and select the appropriate Playback buttons. Important note for tuners: If your CSP5 tune does not seem to be switching as expected please check the data in the "AIRDENSC_F" PID. For CSP5 to work correctly the "AIRDENSC_F" PID must be in 'Mode5, Normal Mode." If any other modes are active (e.g. Protection Mode) then the ECM will not be using normal Altitude based tables, and therefore will not using the CSP5 tables. Protection Mode is a direct result of tuning strategy or DPF regen states. Pass-Thru Licence and Flash a Controller Follow these steps to license and flash the selected controller. 1. Open the EFILive Scan and Tune application. 2. Connect your FlashScan/AutoCal to your PC and your vehicle. 3. Turn the vehicle ignition to the On position, (not the Accessory position. Vehicle must not be cranked/running when flashing). 4. Select the [F3: Tune] option in the left-hand pane. 5. Click on the Open button and select the calibration file for the controller you wish to flash or license.

[email protected] - 13 - www.efilive.com 6. If tune file security has been applied to the tune file, review and accept the Security Warning. 7. Click on the [F7: Full Flash] options in the left-hand pane. 8. Click on the Check License button. This will indicate if the controller is already licensed or needs to be licensed. 9. Where the controller is NOT licensed, select Activate License to license the controller. 10. Select Yes to license the controller or No to close this window without licensing the controller. 11. Select Yes to license the controller or No to close this window without licensing the controller. 12. Select the Full Flash button to commence the flash. 13. While the ECM is flashing an Elapsed time indicator, an Estimated Time Remaining indicator, and a Progress bar will display tracking the Flash progress. 14. When the flash process is complete a countdown timer will be shown. When prompted perform the following actions: a. Turn the vehicle ignition Off. b. Click on the Start button to begin the countdown timer. c. DO NOT turn the vehicle ignition on until the countdown timer expires. This time is critical to allow the ECM to perform internal functions after a read operation.

[email protected] - 14 - www.efilive.com Configure FlashScan/AutoCal for BBX There are a range of configuration files that must be installed on FlashScan and AutoCal devices before the device can be used in standalone mode (BBX). Follow these instructions to configure your FlashScan or AutoCal for BBX. 1. Connect your FlashScan or AutoCal to your PC. 2. Open the EFILive V8 Scan and Tune application. 3. Select the [F5: BBX] option in the left-hand pane. EDA Data Logging The EDA PID group aims to simplify the task of information sharing between users as every individual data parameter has been selected with tuning feedback in mind. If you choose to log additional data streams alongside the EDA stream it may slow the data logging rate down by as much as 70%. For FlashScan V2 and AutoCal V2, BBL is only supported where CSP5 and EDA are installed. For FlashScan V3 and AutoCal V3, BBL is supported regardless of whether CSP5 is installed. To configure EDA data logging; 1. Select the [F2: Scan] option in the left-hand pane. 2. Remove any unnecessary controller configurations to ensure capacity restrictions are not exceeded. 3. Add your chosen controller(s) to your list; a. Press the green '+' icon. b. Right click on the Engine Controller box. c. Navigate to Select CME. d. Select OK. 4. Click on the CME controller in the “BBL Enabled Controllers” window. 5. Highlight the EDA 1 folder in the “Available PIDs” window and drag into the “Selected PIDs” window. *NOTE: For FlashScan/AutoCal V2 BBL is only supported for Cummins Controllers that have CSP5 and EDA installed. Users

[email protected] - 15 - www.efilive.com MUST select the entire EDA PID Group and flash a CSP5 operating system into the ECM for effective data logging. Configure Tuning To configure flashing of CME controllers on your FlashScan/AutoCal device; 1. Select the [F3: Tune] option in the left-hand pane. 2. Remove any unnecessary controller configurations to ensure capacity restrictions are not exceeded. 3. Add your chosen controller(s) to your list; a. Press the green '+' icon. b. Right click on the Engine Controller box. c. Navigate to Select CME. d. Select OK. Tune File Switching To configure the switching of CSP5 tune positions on your FlashScan/AutoCal device; 1. Select the [F4: Switch] option in the left-hand pane. 2. Enter switchable tune names as appropriate. Configure DTCs To configure the display of trouble codes and descriptions onto FlashScan; 1. Select the [F5: DTC's] option in the left-hand pane. 2. Select appropriate DTC options. Quick Setup To configure BBX settings, device settings, and configure tune files for BBX;

[email protected] - 16 - www.efilive.com 1. Select the [F6: Quick Setup] option in the left-hand pane. 2. Select appropriate BBX configuration options. 3. Edit device settings as necessary. To prevent manually selecting the CME PID group each time FlashScan/AutoCal is powered, the most recent PID group selection can be automatically selected by: a. Selecting the correct hardware on the [F6: Quick Setup] -> [Edit AutoCal V3 Settings] button. b. In the Device Settings window, navigate to [F6: Logging] and tick the “At start-up, automatically re-select the most recently used PID list.” 4. Add tune files to the Quick Setup using the green '+' icon. 5. Write this configuration to FlashScan or AutoCal using the [Program Quick Setup] function. The [Program Quick Setup] programs all selected Scan, Tune, Switch, and DTC options, as well as selected device settings, BBX Quick Setup selections and tune files. Once the device is programmed, FlashScan or AutoCal is configured for BBX functions. Each option can be programmed individually using the [Program] button on each tab, or collectively using the [Program Quick Setup] option.

[email protected] - 17 - www.efilive.com FlashScan Menu Navigation FlashScan/AutoCal V3 FlashScan/AutoCal V3 supports two menu structures; the EFILive standard menu and the user defined menu. Where a used defined menu is not installed, the EFILive standard menu will be displayed. Data Logging 1. Configure FlashScan/AutoCal V3 for BBX features if not already setup. 2. Connect your FlashScan/AutoCal V3 device to your vehicle. 3. Turn the vehicle ignition to the On position 4. Navigate to the Scan Tool -> F1 Select PIDs menu option. 5. Select correct controller type from BBX configured controllers. 6. Navigate to the F1 Scan Tool -> F2 Data Logging menu option. 7. Select F1: Record Data to commence the logging session. 8. The LCD will display recording status, elapsed time, frame count and the selected PIDs. 9. A range of options are available while the Log is recording: 1. Select ✔ to pause/resume the log. 2. Select the up and down arrows to navigate through selected PIDs. 3. Select X, to save the log. 10. Start the vehicle and drive to record actual performance. 11. Stop the vehicle and turn the ignition off prior to selecting X on FlashScan/AutoCal V3 to save the log file. License and Flash a Controller 1. Configure FlashScan/AutoCal V3 for BBX features if not already setup. 2. Copy selected tune file(s) from your PC to FlashScan/AutoCal V3 if not already copied via Quick Setup during step 1. 3. Connect your FlashScan/AutoCal V3 device to your vehicle. 4. Turn the vehicle ignition to the On position (not the Accessory position. Vehicle must not be cranked/running when flashing). 5. Navigate to the Tune Tool menu and select F1: Tuning -> F3 Program Full menu option. 6. Navigate to the folder your tune file is located in and select ✔ to commence the flash. 7. If the controller has not been licensed by the device previously, you will be presented with an Unlicensed Controller message. Select ✔ to proceed with licensing the controller, or X to exit. 8. Select ✔ to confirm licensing the controller and commence the flash, or X to exit. 9. When the flash process is complete, select X to close the flash completed message. 10. The Reset Controller notification will be shown, and the controller reset process will begin. 1. Turn the vehicle ignition Off.

[email protected] - 18 - www.efilive.com 2. Click on the Start button to begin the countdown timer. 3. DO NOT turn the vehicle ignition on until the countdown timer expires. This time is critical to allow the ECM to perform internal functions after a read operation. Switch Tunes using FlashScan/AutoCal V3 1. Connect your FlashScan/AutoCal V3 device to your vehicle. 2. Turn the vehicle ignition to the On position 3. Navigate to the Tune Tool menu and select F3 Switch Tunes -> F1 Switch CSP5 menu option. 4. Use the arrows to navigate between tunes. 5. Press ✔ to make a tune selection. 6. If you attempt to select a tune higher than #4 you will see an error that indicates the tune # is not supported. The ECM will ignore this request and keep the last valid tune selected. 7. You do not need to reselect the tune once the engine is shut down; the ECM 'remembers' which tune you previously selected. FlashScan V2 Data Logging 1. Configure FlashScan V2 for BBX features if not already setup. 2. Connect your FlashScan V2 device to your vehicle. 3. Turn the vehicle ignition to the On position 4. Navigate to the F1 Scan Tool - F1 Select PIDs menu option. 5. Select correct controller type from BBX configured controllers. 6. Navigate to the F1 Scan Tool - F2 Data Logging menu option. 7. Select F1: Record Data to commence the logging session. 8. Start the vehicle and drive to record actual performance. 9. Stop the vehicle and turn the ignition off prior to selecting Cancel on FlashScan V2 to save the log file.

[email protected] - 19 - www.efilive.com NOTE: When data logging is activated you cannot return to the tune selection menu unless logging is stopped. License and Flash a Controller 1. Configure FlashScan V2 for BBX features if not already setup. 2. Copy selected tune file(s) from your PC to FlashScan V2 if not already copied via Quick Setup in step 1. 3. Connect your FlashScan V2 device to your vehicle. 4. Turn the vehicle ignition to the On position, (not the Accessory position. Vehicle must not be cranked/running when flashing). 5. Navigate to the F2 Tune Tool -> F1 Tuning and select F3 Program Full menu option. 6. Using the arrow keys, navigate to the correct tune file and select OK. 7. If the controller has not been licensed by the selected FlashScan V2 previously, you will be presented with the License this controller now? message. Select Yes to license the controller or No to exit. 8. Select Yes to confirm licensing the controller and commence the flash, or No to exit. 9. When the flash process is complete the Reset Controller notification will be shown. When prompted perform the following actions: a. Turn the vehicle ignition Off. b. Click on the Start button to begin the countdown timer. c. DO NOT turn the vehicle ignition on until the countdown timer expires. This time is critical to allow the ECM to perform internal functions after a read operation.

[email protected] - 20 - www.efilive.com Switch Tunes using FlashScan V2 1. Connect your FlashScan V2 device to your vehicle. 2. Turn the vehicle ignition to the On position 3. Navigate to the F2 Tune Tool -> F3 Switchable Tunes menu option 4. Select PIDs 5. Use the arrows to navigate between tunes. 6. Press OK to make a tune selection. 7. If you attempt to select a tune higher than #4 you will see an error that indicates the tune # is not supported. The ECM will ignore this request and keep the last valid tune selected. 8. You do not need to reselect the tune once the engine is shut down; the ECM 'remembers' which tune you previously selected.

[email protected] - 21 - www.efilive.com Support Trouble Shooting Should users encounter problems with upgrading to CSP5 they should: 1. Confirm software, firmware and boot block versions match the CSP5 minimum requirements. 2. Confirm CSP5 file was upgraded to new operating system number, as sequenced above. 3. If you are concerned your device is not switching between tunes, edit your tunes to see a notable difference (ie Pedal to Desired Fuel table), reflash and then test. Also note the EDA data stream has a parameter that indicates which tune the ECM is running 4. CSP5 tune files cannot be read from the ECM. Error Codes If an error occurs while using AutoCal, users can look up the error code description in the EFILive V8 Scan and Tune software. The [F8: Tools] -> [F8: Error Codes] menu item provides an error code lookup function, and the “EFILive Error Codes.pdf” document accessed by selecting the Windows Start Icon and navigating to Program Files->EFILive->V8->Documents- >EFILive Error Codes.pdf is also available. Both options provide error code descriptions, causes and actions. Should the issue not be resolved after reviewing the Error code list, end users should contact their Tuner for support. Test for Rogue Modules For Customers with FlashScan/AutoCal V3 a range of test modes to check the network for rogue modules that may cause read or flash operations to abort are available. Navigate to the Tune Tool -> F1: Tuning -> F4: Test OBD Network menu. Select the Test CAN J1979 option. Trace Files V8 Scan and Tune *.htx files When V8 Scan and Tune software reads or flashes a controller the details of the read/flash process may be saved in trace files for diagnostic purposes. In addition, users can manually save trace files where options do not perform the desired outcome. To manually generate a trace file, generate the error in V8 software, then open the EFILive Control Panel and navigate to [F8: Trace] and select [Save Trace]. Users can set the trace file and save location during this process.

[email protected] - 22 - www.efilive.com Automatically generated trace files are created on your PC or laptop in the folder: \Documents\EFILive\V8\Trace and are named using the following naming convention: YYYYMMDD_HHNNSS_T_CCC.htx, where:  YYYYMMDD: is the year, month and day that the trace was recorded.  HHNNSS: is the hour, minute and second that the trace was recorded.  T: is the mode and is one of R=Read F=Full-Flash W=Cal-Flash.  CCC: Is the controller type  htx: is the file extension. FlashScan/AutoCal V3 *.xalm files Trace files are automatically saved where an error message is presented using the device in BBX mode. Users can manually save trace files where options do not perform the desired outcome, including for pass-thru functions. To manually generate a trace file on FlashScan/AutoCal V3 navigate to Scan Tool -> F3: Scan Options -> F1: Save Trace. Trace files are located in the EFILive -> Trace folder on FlashScan/AutoCal V3. Trace files are named using the following naming convention: yyyymmdd_hhnnss_.xalm, where:  yyyymmdd: is the year, month and day that the trace was recorded.  hhnnss: is the hour, minute and second that the trace was recorded.  : is the description where; o “User” means user generated trace files o “xxx._x_$xxxx” identifies the 3 character controller ID, the communication process upload/download, and the 4 digit error code.  xalm: is the file extension. FlashScan V2 Trace Files Trace files are automatically saved where an error message is presented using the device in BBX mode. Users can manually save trace files where options do not perform the desired outcome. To manually generate a trace file on FlashScan V2 navigate to F1 Scan Tool -> F3 Scan Options -> F1 Save Trace File. FlashScan V2 maintains an internal buffer of the most recent messages sent to and received from the vehicle. That buffer is stored in RAM memory and is wiped clean each time the device is powered off or rebooted. Therefore you MUST save the trace file before powering off or rebooting the device. Trace files are located in the Scan folder on FlashScan V2. It will be named USR_xxxx.efx, where xxxx is the unique file counter number. Knowledgebase The EFILive Knowledgebase provides a detailed resource on how to configure and use your EFILive software and hardware.

[email protected] - 23 - www.efilive.com EFILive Authorized Dealer If after reviewing this guide further assistance is required please contact the EFILive Authorised Dealer from whom you purchased your product. They are your first point of contact for EFILive support related inquiries. How to Tune? EFILive is tuning software and hardware - it is not a tune. Together the software and hardware give users the tools to write tunes. EFILive does not provide tune files, tuning advice or support, but do provide software support and hardware support. If your question is in relation to the actual tuning of your vehicle (e.g. how to gain performance, economy etc.) then please ask these questions on the EFILive Forum (http://forum.efilive.com/). EFILive Service Desk Should you require additional assistance after using this support guide, please start a ticket on the EFILive Service Desk. Please include the following information: 1. Dealer Name. 2. Device type. 3. Serial Number and Auth Code. 4. Your computer operating system. 5. Software and firmware versions. 6. Trace files. 7. Detailed information about your issue.