Datalogic MAGELLAN 3410VSi Quick Reference Manual

40012 Calderara di Reno — Italy Tel. +39 051 3147011 Fax +39 051 3147205 ©2020 Datalogic S.p.A. and/or its affiliates All rights reserved. Without limiting the rights under copyright, no part of this documen- tation may be reproduced, stored in or introduced into a retrieval system, or transmitted in any form or by any means, or for any purpose, without the express written permission of Datalogic S.p.A. and/or its af ...

TABLE OF CONTENTS Features .......................................................................... 1 Installation ....................................................................... 3 Wall/Desk Mount .......................................................................... 5 Installation Instructions ...........................................................5 Desk (Horizontal) Mounting ................................. ...

MAGELLAN™ 3410VSI Use this guide to quickly complete installation of the Magellan 3410VSi series of bar code readers, and begin using your scanner. For more details and programming information, reference the Product Reference Guide (PRG), which is available for viewing and download from the Datalogic website (www.datalogic.com). FEATURES Figure 1. Scanner Features - Front View Wall/Desk Mount Scanner Button Camera Button Scan Cab ...

Figure 2. Scanner Features - Back View Figure 3. Scanner Features - Bottom View Cable Routing Area Serial Number Label Regulatory USB Micro B/ MicroSD Card Port Label (Service Access) USB Aux Port Power Host Port Cavity for EAS Connection Wire MicroSD Card USB Micro B ...

INSTALLATION Connect the scanner to the host (terminal) using the interface (I/F) cable, as shown in the following figures. A cable from an older existing installation can be re-used for RS-232 interfaces. If external power is used/needed, plug the AC Adapter into the AC wall outlet, then connect it to the unit as shown in Figure 5 on page 4. The USB AUX PORT will only be supported by using a 12V power supply or using a USB + POWE ...

Figure 5. Powered by AC Adapter Figure 6. USB Cable Type A Power Off the Terminal NOTE: This cable (or similar) will not support a USB peripheral. The system must be powered by 12V in order for a peripheral to be attached to the AUX USB PORT. U S B R S - 2 3 2 RS-232 and USB Cables Powered by AC Adapter To Terminal (PC) U S B To Terminal (PC) USB Type A Power Off the Terminal ...

Wall/Desk Mount The Wall/Desk Mount is an accessory part to which the scanner can be attached. The accessory can be mounted horizontally to a desk, countertop, or table using screws or a gooseneck stand. It can also be mounted vertically to a wall using screws, or to a VESA mount. Installation Instructions 1. Determine the mounting location. While deciding on the best position, keep in mind the best way to route the scanner cables ...

Figure 8. Desk Mounting Dimensions Wall (Vertical) Mounting Figure 9. Wall mount 63 41 92.5 ALL UNITS ARE IN MM 50 mm #8 screws screw holes VESA mount ...

Figure 10. Wall (Vertical) Dimensions 75 42.5 130.2 135.5 50 55 132.1 ALL UNITS ARE IN MM ...

Attaching/Detaching the Scanner The scanner attaches or detaches from the Wall/Desk Mount as shown in the illustration below. Seating the Scanner in the Mount 1. Guide the scanner diagonally down, seating the L-Bracket tabs on the Mount into the scanner’s slots. 2. Push the scanner down to snap into place. Detaching the scanner 1. Tilt the top of the scanner forward, separating it slightly from the back of the mount. 2. Pull up to ...

Bottom Cover / Tilting Riser To remove the Bottom Cover, put your finger in the hole and pull it away from the scanner, at an angle. The snaps will disengage on that side and the cover will release from the scanner. Attach the Tilting Riser by snapping into the place of the Bottom Cover. Figure 12. Attaching the Tilting Riser When removing the Tilting Riser, note that the snaps on the riser may be tight. If necessary, use a coin o ...

Mounting the Riser The Adjustable Riser can be mounted to a flat surface using two #8 screws. Figure 13. Mounting the Tilting Riser Figure 14. Tilting Riser Dimensions 64.2 23.8 ALL UNITS ARE IN MM ...

HOW TO SCAN Bar codes can be presented to the scanner’s window or pushed past it using a “sweep” technique. The scanner can also be programmed to ini- tiate a scan of a cell phone or other LCD bar code object, or an image capture upon pushing the Camera Button. Scanner Button The Scanner Button performs multiple functions, depending on how long it is pressed: NOTE: Volume changes made using the Scanner Button are lost when ...

Camera Button The Camera Button provides the unit with the ability to capture images. See “Camera Button Mode” on page 18 to enable this feature. Destination and image type can be specified. Reference the PRG for additional information and programming options. Momentary (when scanner is awake) Increments volume Press the button momentarily to increase speaker volume. When the loudest volume is reached, a repeated press of the b ...

LED AND BEEPER INDICATORS The scanner’s beeper sounds and its green LED illuminates to indicate various functions or errors on the scanner. The tables that follow list these indications. An exception is that the scanner’s functions are programmable, and may or may not be turned on. For example, some indications (such as the power-up beep) can be disabled using programming bar code labels. LED INDI- CATION INDICATION COMMENT P ...

Beeper Indicators TROUBLESHOOTING BEEPER INDICATION COMMENT Power On Beep Single beep The Power-On LED indication is a configurable feature which can be enabled or disabled. When enabled, this beep indicates the scanner has finished all its power-up tests and is now ready for operation. Good Read Indication Single beep The good read beep indication is configurable. Options include: Enable/ disable, frequency, duration and volume. S ...

ERROR CODES If an error is detected, the scanner will sound a long low tone (for three seconds) and flash its LED, indicating a failure. When this occurs, press the Scanner button to hear the error code. If it is configured to do so, the scanner will sound a series of beeps corresponding to the error code and/or flash its LED simultaneous to the beeps. The table below describes what these codes mean and what action should be take ...

PROGRAMMING Upon completing the physical connection between the scanner and its host, proceed directly to the Programming Bar Codes table below to locate the interface type the scanner is connected to (for example: RS- 232, USB, etc.). Use the Bar Code Mask at the back of this manual to isolate the bar code you intend to scan. Scan a START/END bar code once to enter Programming Mode. After scanning the programming label for the des ...