Binks QS-5012-CE Instructions Manual

EN EN P 1 - 12 DD P 24 - 34 FF P 13 - 23 NL NL P 35 - 45 IT IT P 46 - 56 AIR MOTOR DRIVES and AGITATORS for PRESSURE FEED TANKS IMPORTANT: Read and follow all instructions and SAFETY PRECAUTIONS before using this equipment. Retain for future reference. SBBI-E-19-095 iss1 ...

AIR MOTOR DRIVES and AGITATORS for PRESSURE FEED TANKS IMPORTANT: Read and follow all instructions and SAFETY PRECAUTIONS before using this equipment. Retain for future reference. DESCRIPTION This manual covers the following models; QS-5012-CE Air motor drive with 15:1 gear reduction. Includes air adjusting for speed control with hose ...

The following hazards may occur during the normal use of this equipment. Please read the following chart. HAZARD CAUSE SAFEGUARDS EXPLOSION STATIC ELECTRICITY Use of this equipment in a p o t e n t i a l l y e x p l o s i v e atmosphere. Vapours from flammable liquids can catch fire or explode from static electricity discharges. 1. If ...

INSTALLATION Air Supply Air supplies (compressors etc) shall be sited in a non-hazardous area with a filter on the air intake system to prevent the ingress of dust or similar foreign material into the parts where compression takes place. Pressure Relief Procedure Before attempting any installation of agitators onto pressure feed tanks, ...

shown in fig 2. The curved edge of the paddle should be at the bottom. Upper paddle on 60L QMS-434-CE only. QS-430-CE Direct Drive Agitator— INSTALLATION into Pressure Feed Tank (Fig. 9) 1. Follow the pressure relief procedure at the start of the INSTALLATION section. 2. Unscrew the centre blanking plug from the tank cover. Clean the ...

about 100ml (4 fluid oz) of solvent into the air intake port of the motor. Rotate the motor by hand in both directions for a few minutes. 8. Re-connect the airline and cover the exhaust port with a cloth. Apply low pressure 0.7bar (10psi) and re-start the motor. Run until no more traces of solvent can be seen. 9. The motor should be ru ...

Fig 4 Ref. No. Replacement Part No. Description Individual Parts Req. 36 QS-190 End Cap 1 •37 - End Cap Gasket 1 38 PT-58 Bearing 1 39 Purchase Locally Machine Screw 1/4”-28 x 1/2” 1 40 QS-333 Front plate 1 •41 PT-59-1-K10 End Plate Gasket Kit (kit of 10) 2 42 QS-189-1-K10 Dowel Pin (kit of 10) 4 43 QS-335 Body 1 •44 - Vane 4 ...

Ref. No. Replacement Part No. Description Individual Parts Req. • 82 - Filister Head Machine screw 10- 24 x 5/8” 4 83 QS-108 Pressure Relief fitting 1 84 QS-37-1 Cover Plate 1 • 85 - Washer 1 86 QS-416-1 Gear & Shaft assy. 1 • 87 - Gasket 1 88 Purchase locally Pipe Plug 1/4” Galvanized 1 89 QS-36-1 Housing 1 • 90 - Oil Seal ...

Fig 7 QMS-431, 433 and 434 AGITATOR PARTS LIST Ref. No. Part No. Description No of Parts Req. 19 QMS-431-CE Agitator Assembly 8L (includes items 20 to 31) 1 QMS-433-CE Agitator Assembly 40L 1 QMS-434-CE Agitator Assembly 60L 1 20 QMS-46 Retaining Nut 1 21 QMS-447 Thrust Collar Kit (includes items 22 and 23) 1 22 — Thrust Collar 1 � ...

Parts list for PT-427-CE, PT-418-CE, PT-419-CE & PT-428-CE Fig 8 Ref. No. Replacement Part No. Description Individual Parts Req. * 35 PT-410 83C Air Motor Assembly 1 QMS-455 83Z 36 QS-190 83C End Cap 1 PT-65 83Z * 37 ——– End Cap Gasket 1 38 PT-58 Bearing 1 39 ——– Screw (1/4”-28 x 1/2”) 12 * 40 ——– Front Plate 1 * ...