modway EEI-537 Manual 

EEI –537 CHAIR Hardware: Component: A Medium Bolt M6x27mm x 4 B 1 Chair Body x1 3 Chair Leg x1 1. 2. 3. 4. 5. 6. F G H Allen Wrench M4 x 1 1 D 2 3 2 Chair Leg x1 Short Bolt M6x20mm x 1 C Long Bolt M6x35 mm x 4 Nut M6 x 5 E Metal Support x 2 Thank you for purchasing the MODWAY CHAIR! Before you start, here is some helpful advice: We suggest you spend a short time reading through this leaflet and then follow the simple step-by-step instructions. Owing to the size and weight of the dining chair, we recommend that it is assembled by two adults, on a carpeted or padded area, in the room that it is intended for. Approximate assembly time: 30 minutes. Please do not use any tools other than those provided or recommended in these instructions. Please do not throw away any of the packaging or instructions until you have checked all the components and hardware and the furniture is fully assembled. Assemble all components loosely until advised to tighten. Depending on use, it may be necessary to tighten the components from time to time, so please save the tools that have been provided. Please keep all pieces out of reach of children. Door Mat x 4 Plastic Washer x 4

EEI –537 CHAIR Hardware & Tool required STEP 1: STEP 2: Gx4 Hardware & Tool required Insert 2 pieces of Plastic Washer (G) into the end of Chair Leg (2) as shown. Move the Plastic Washer (G) on the right Position, and make sure the holes on Plastic Washer (G) align to the holes on Chair Leg (2). Repeat the same step for the remaining Chair Leg (3). Hx4 Insert 2 pieces of Leg Cover (H) into the bottom of Chair Leg (2) as shown. Repeat the same step for the remaining Chair Leg (3). H 2 3 H 2 3 2 G G G G G G H H

EEI –537 CHAIR STEP 1: STEP 2: Bx1 D D x1 Fx1 Hardware & Tool required Hardware & Tool required Ax4 Dx4 Ex2 Fx1 2 2 B 3 F E E D 2 3 3 F 3 A 2 Please put Chair Legs (2&3) upside down on a carpeted or padded area. Place Chair Leg (3) to the bottom of Chair Leg (2) as shown. Insert 1 piece of Short Bolt (C) through the holes on Chair Leg (3) into Chair Leg (2) as shown. Secure 1 piece of Nut (D) into Short Bolt (B) by hand. Use Allen Wrench (F) to tighten Short Bolt (B) clockwise until secure. Place 1 piece of Metal Support (E) under the assembled Chair Legs (2&3), and the other piece of Metal Support (E) on top of Chair Legs (2&3) as shown. Insert 4 pieces of Medium Bolt (A) through the holes on bottom Metal Support (E) and Chair Leg (2&3) into the holes on top Metal Support (E) as shown. Secure 4 pieces of Nut (D) into Medium Bolts (A) by hand. Use Allen Wrench (F) to tighten Medium Bolts (A) clockwise until secure.

EEI –537 CHAIR STEP 4: Assembly is complete. Your chair is ready to be enjoyed now! Carefully turn over the assembled chair. Cx4 Fx1 Hardware & Tool required STEP 3: 3 1 C 3 2 2 1 2/3 Place the assembled Chair Legs (2&3) to the bottom of Chair Body (1) as shown. Attach by using 4 pieces of Long Bolt (C) as shown. Use Allen Wrench (F) to tighten Long Bolts (C) clockwise until secure. G F