Crown 1400CSL Service Manual

Text of Crown 1400CSL Service Manual

Power Base-3 & 1400CSL Amplifier Service Manual

1 POWER BASE ™-3 & 1400CSL ™ POWER AMPLIFIER SERVICE MANUAL K-SVCPB3 6-95 CSL™ and Power Base™ are trademarks, and ODEP® and Crown® are registered trademarks of Crown International, Inc. Mailing Address: P.O. Box 1000 Elkhart, IN U.S.A. 46515-1000 Shipping Address: 57620 C.R. 105 Elkhart, IN U.S.A. 46517 ©1995 by CROWN INTERNATIONAL, INC.
Power Base-3 & 1400CSL Amplifier Service Manual 2 À PRÉVENIR LE CHOC ÉLECTRIQUE N’ENLEVEZ PAS LES COUVERTURES. RIEN DES PARTIES UTILES À L’INTÉRIEUR. DÉBRANCHER LA BORNE AVANT D’OUVRIR LA MODULE EN ARRIÈRE. TO PREVENT ELECTRIC SHOCK DO NOT REMOVE TOP OR BOTTOM COVERS. NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. DISCONNECT POWER CORD BEFORE REMOVING REAR INPUT MODULE TO ACCESS GAIN SWITCH. CAUTION AVIS W
Power Base-3 & 1400CSL Amplifier Service Manual 3 Introduction ............................................................. 4 Scope ...................................................................... 4 Warranty .................................................................. 4 Parts Information ..................................................... 5 Specifications .......................................................... 6 Voltage Conversion .......
Power Base-3 & 1400CSL Amplifier Service Manual 4 Crown Technical Support Group Factory Service Parts Department Mailing Address: PO Box 1000 Elkhart, IN USA 46515-1000 Shipping Address: 57620 C.R. 105 Elkhart, IN USA 46517 Phone: (219) 294-8200 Toll Free: (800) 342-6939 FAX: (219) 294-8301 This manual contains service information on Crown power amplifiers. It is designed to be used in conjunc- tion with the applicable Owner's Manual. However, some i
Power Base-3 & 1400CSL Amplifier Service Manual 5 Parts Information shipment on a C.O.D. or pre-payment (check or credit card) basis. TERMS Normal terms are pre-paid. Net-30 Days applies to only those firms having pre-established accounts with Crown. If pre-paying, the order must be packed and weighed before a total bill can be established, after which an amount due will be issued and shipment made upon receipt of pre-payment. New parts re- turned for cred
Power Base-3 & 1400CSL Amplifier Service Manual 6 Specifications Unless noted otherwise, all specifications are based on driving an 8 ohm load per channel, both channels driven, the sensitivity switch in the 26dB position, the AC supply is 120VAC at 60Hz. Crown specifications are guaranteed through the warranty period (normally 3 years). Because our testing methods are more strin- gent than our published specifications, every Crown amplifier will exceed it
Power Base-3 & 1400CSL Amplifier Service Manual 7 Voltage Conversion Note: The only versions of this product produced at the Crown Factory with international volt- age capabilities are the CSL versions built specifically for sale outside the United States. P16 P10 P15 P14 P13 P12 P11 P9 P8 P7 P6 P5 P4 P3 P2 P1 P22 P21 P18 P17 P19 P20 F1 F100 BRN BLU 100V Connections: P10 to P15 P11 to P14 P7 to P12 120V Connections: P10 to P16 P11 to P14 P7 to P13 220V Con
Power Base-3 & 1400CSL Amplifier Service Manual 8 Theory OVERVIEW It should be noted from the outset that the PB-3 and 1400CSL amplifiers are electrically and mechanically identical products. The only differences, from a ser- vice perspective, are cosmetic. It should also be noted that over time Crown makes improvements and changes for various reasons. This manual is up to date as of the time of writing. For additional information regarding these amplifier
Power Base-3 & 1400CSL Amplifier Service Manual 9 Theory output of the amplifier at 26 dB. Diodes prevent overdriving the Error Amp. Because the Error Amp amplifies the difference between input and output signals, any difference in the two waveforms will produce a near open loop gain condition which in turn results in high peak output voltage. The output of the Error Amp, called the Error Signal (ES) drives the Voltage Translators. VOLTAGE AMPLIFICATION Th
Power Base-3 & 1400CSL Amplifier Service Manual 10 ultra low distortion in the signal zero-crossing region and high efficiency. High Side (HS) The High Side (HS) of the bridge operates much like a conventional bipolar push-pull output configuration. As the input drive voltage becomes more positive, the HS NPN conducts and delivers positive voltage to the load. Eventually the NPN devices reach full conduc- tion and +Vcc is across the load. At this time the
Power Base-3 & 1400CSL Amplifier Service Manual 11 In other words, the high voltage power supply floats with respect to ground, but ±Vcc remain constant with respect to each other. This allows the power supply to deliver +Vcc and -Vcc from the same bridge rectifier and filter as a total difference in potential, regardless of their voltages with respect to ground. The LS uses inverted feedback from the HS output to control the ground reference for the rail
Power Base-3 & 1400CSL Amplifier Service Manual 12 Theory NEGATIVE LOW SIDE OUTPUT PNP STAGE POSITIVE LOW SIDE OUTPUT NPN STAGE NEGATIVE HIGH SIDE OUTPUT PNP STAGE POSITIVE HIGH SIDE OUTPUT NPN STAGE HIGH SIDE BIAS SERVO +LVA -1 -LVA -1 +VOLTAGE TRANSLATOR -VOLTAGE TRANSLATOR OUTPUT DEVICE EMULATION PROTECTION ERROR AMP VGS BGS BALANCED INPUTS INVERTING BRIDGE BALANCE LOW SIDE BIAS DIODE STRING -1 -1 MAIN NEGATIVE FEEDBACK (NFb) LOOP Figure 3. Typical Crow
Power Base-3 & 1400CSL Amplifier Service Manual 13 Electrical Checkout Procedures GENERAL INFORMATION The following test procedures are to be used to verify operation of this amplifier. DO NOT connect a load or inject a signal unless directed to do so by the proce- dure. These tests, though meant for verification and alignment of the amplifier, may also be very helpful in troubleshooting. For best results, tests should be performed in order. All tests assu
Power Base-3 & 1400CSL Amplifier Service Manual 14 TEST 6: VOLTAGE GAIN Spec 26dB Gain: ±3%. Spec 0.775V Sensitivity: ±6%. Spec 1.4V Sensitivity: +12%/–6%. Initial Conditions: Controls per standard. Procedure: No load connected. Inject a 0.775 VAC 1 kHz sine wave with the Sensitivity Switch in the 26 dB position. Measure 15.5 VAC ±0.5 VAC at the amplifier output. Inject a 0.775 VAC 1 kHz sine wave with the Sensitivity Switch in the 0.775V position. Me
Power Base-3 & 1400CSL Amplifier Service Manual 15 Electrical Checkout Procedures TEST 14: ODEP LIMITING Spec: No oscillation on ODEP Limiting wave form; either channel controls limiting in Parallel Mono Mode. Initial Conditions: Controls per standard; rag or other obstruction blocking fan so that it does not turn. Procedure: Load the amplifier to 4 ohms on each channel. Inject a 60 Hz sine wave and adjust for 35 Vrms at the output. After a few minutes obs
Power Base-3 & 1400CSL Amplifier Service Manual 16 Parts List (Non-Module) SUPPLIMENTAL ITEMS CPN ITEM QTY D 4137-2 Nylon Thumbscrew Washer 4 C 3342-0 Feet, Black Self-Stick 4 A10087-71012 10-32 .75 Machine (Rack Screw) 4 K80607-3 PB Series Owners Manual 1 POWER SUPPLY CPN ITEM QTY C 9837-3 Breaker, 30A 250VAC (100-120VAC) 1 C 9839-9 Breaker, 15A 250VAC (200-240VAC) 1 A10285-33 Fuse F1, .3A Slo Blow (120V 60Hz UL approved only) 1 A10285-7 Fuse F1, .5A AGC

Crown Amplifier Owners Instructions: