Kramer K-Cam4K Quick Start Manual

MODEL: K-Cam4K 4K PTZ Camera P/N: 2 9 0 0 - 3 0 1 5 3 0 QS Rev: 1 SAFETY WARNING Disconnect the unit from the power supply before opening and servicing For the latest information on our products and a list of Kramer distributors, visit our Web site where updates to these installation instructions may be found. We welcome your questions, comments, and feedback.

K-Cam4K 4K PTZ Camera Congratulations on purchasing your Kramer K-Cam4K 4K PTZ Camera (Pan Tilt Zoom camera). K-Cam4K includes an ultra- low, 8.51Mpixel CMOS image sensor that together with 3D DNR technology, delivers high image quality of up to 4K at 30fps. K-Cam4K includes HDMI, RJ-45 and USB 3.0 outputs for easy plug-and-play and features x12 zoom, a ±30° tilt, a 71° field of view and a ±170° pan. Control K-Cam4K via the IR remote controller, OSD or embedded webpages. Go to www.kramerav.com/downloads/K-Cam4K to download the latest user manual and check if firmware upgrades are available. Get to know your K-Cam4K # Feature Function 1 Camera Front and rear views. 2 Front Panel OLED Displays frame rate and resolution for HDMI and SDI output signals, as well as the IP address. 3 Tilting Mechanism Can be set to any of 255 preset positions. 4 RESET Press for 5 seconds to reset to factory default parameters. 5 NET RJ-45 Connector Connect to your network or directly to a computer (supports PoE). 6 RS-232 8-pin DIN Connector IN RS232 8-pin DIN Connector 7 OUT 8 RS-485 2-pin Terminal Block Connector Connect to a controller. 9 LINE IN 3.5mm Mini Jack Connect to a microphone. 10 HDMI Out Connector Connect to a recording/streaming device. 11 3G-SDI Out BNC Connector Connect to a recording/streaming device. 12 USB 3.0 Type-B Connector Connect to computer or collaboration device using the USB-3 cable (included). 13 DC12V Power Connector Connect to the 12V power adapter. 14 ON/OFF Switch Turn the unit on and off.

image orientation. • Ensure that the environment (e.g., maximum ambient temperature, humidity & air flow) is compatible for the device. • Avoid exposing the product to direct sunlight or any other heat source. • Keep away from children – product includes small accessories and components. • Avoid uneven mechanical loading. • Do not insert any sharp objects into the product. • Avoid dropping or hitting the product to avoid damaging the product. • For maintenance, call tech support. To attach K-Cam4K onto a wall: 1. Find the correct location on the wall. 2. In the desired location, mark the hole locations, then drill 4 holes 82mm and 60mm apart (using a 6mm drill-bit) to fit the 4 holes of the wall-mounting bracket. 3. Insert the four expansion-plugs into the holes. 4. Attach the wall bracket to the wall, using the four wall- bracket screws. 5. Attach the device to the wall bracket by fitting the mortise (on the bracket) into the tenon (on the camera). 6. Fix the camera by screwing (A) Nickel screw to the center and (B) then tighten with 3 black screws. Note that you can also attach the device upside down, from under the bracket. Connecting K-Cam4K Always switch OFF the power on each device before connecting it to your K-Cam4K. Connect the power cord to K-Cam4K and plug it into the mains electricity. Safety Instructions (See www.kramerav.com for updated safety information) Caution: • There are no operator serviceable parts inside the unit. Warning: • Use only the power cord that is supplied with the unit. • Disconnect the power and unplug the unit from the wall before installing. • Do not open the unit. High voltages can cause electrical shock! Servicing by qualified personnel only. • To ensure continuous risk protection, replace fuses only according to the rating specified on the product label which located on the bottom of the unit.

Controlling K-Cam4K via the IR remote controller # Key Function Shortcut Keys *+＃+1: OSD default (English) *+＃+3: OSD default (Chinese) *+＃+4: Display current IP address *+＃+6: Quickly recover the default *+＃+8: View the camera version *+＃+9: Quickly set up inversion *+＃+MANUAL: Restore default IP address 1 Power Press once to enter standby mode. Press again to enter normal operation mode. 2 Number (0 to 9) Configure or edit a preset. 3 * Key Use together with other keys for various functions. 4 PRESET Press PRESET + a numerical key (0 to 9) to save the current configuration to that preset number. 5 HOME Press to return K-Cam4K to its default position. When in the OSD, press to enter a submenu or confirm menu. 6 Return Return to previous item on the menu. 7 ZOOM SLOW Press for slow zoom in (+) or out (-). FAST Press for quick zoom in (+) or out (-). 8 L/R Set STD (1) Press L/R + STD (1) keys to set Pan-Tilt to same direction as L/R setting. REV (2) Press L/R + REV (2) keys to set Pan-Tilt to the direction opposite to the L/R setting. 9 FOCUS AUTO Press to automatically set the focus to the center of the image. MANUAL Press to enter manual focus mode. Then press FAR or NEAR. FAR When in MANUAL mode, press to focus on a far object NEAR When in MANUAL mode, press to focus on a near object. 10 CAMERA SELECT Select the camera to configure and control (1 to 4). 11 # Key Use together with other keys for various functions. 12 IR RC Press * + # + (F1 to F4) to assign a camera address to the remote. For example, point the remote to a camera, press *+#+F1. The remote assigns CAMERA SELECT 1 key to this camera. To use the remote to control camera 1 press the CAMERA SELECT 1 key. Press F4 to freeze the image. 13 RESET Press RESET+ a key number (0 to 9) to delete a preset configuration. Press *+#+RESET to delete all preset configurations. 14 PTZ Control Control camera panning and tilting using arrow keys (left, right, up and down). 15 MENU Enter/exit OSD menu. 16 BACKLIGHT Press to turn backlight compensation on or off. Available when exposure mode is set to Auto (via the OSD menu). 17 P/T RST Press to self-check preset Pan/Tilt on camera. Default Communication Parameters RS-232 Baud Rate: 9600 Data Bits: 8 Stop Bits: 1 Parity: None Command Format: ASCII Ethernet To reset the IP settings to the factory reset values go to: Menu->Setup -> Factory Reset-> press Enter to confirm IP Address: 192.168.100.88 Subnet mask: 255.255.0.0 Default gateway: 192.168.1.2 Default username: admin Default password: admin Full Factory Reset OSD Go to: Menu-> RESTORE DEFAULT -> confirm Reset button Press the RESET button for 5 seconds to reset the machine