OBSIDIAN CONTROL SYSTEMS NETRON EP2 Installation Manual

images, and instructions herein are subject to change without notice. Obsidian Control Systems logo and identifying product names and numbers herein are trademarks of ADJ PRODUCTS LLC. Copyright protection claimed includes all forms and matters of copyrightable materials and information now allowed by statutory or judicial law or hereinafter granted. Product names ...

3 GENERAL INFORMATION 4 LIMITED WARRANTY 5 SAFETY GUIDELINES 6 OVERVIEW 7 INSTALLATION 8 CONNECTIONS 14 MAINTENANCE 16 SPECIFICATIONS 17 DIMENSIONS 18 CONTENTS ...

to operate this device. These instructions contain important safety and use information. UNPACKING Every device has been thoroughly tested and has been shipped in perfect operating condition. Carefully check the shipping carton for damage that may have occurred during shipping. If the carton is damaged, carefully inspect ...

products to be free of manufacturing defects in material and workmanship for a period of two years (730 days). 2. For warranty service, send the product only to the Obsidian Control Systems service center. All shipping charges must be pre-paid. If the requested repairs or service (including parts replacement) are within the terms of this warr ...

follow all instructions and guidelines in this manual. OBSIDIAN CONTROL SYSTEMS is not responsible for injury and/or damages resulting from the misuse of this device due to the disregard of the information printed in this manual. Only the original included parts and/or accessories for this device should be used. Any modifica ...

ports designed for wall mount, truss mount and standalone installations. It is configurable via its internal web remote and powered over Ethernet or via the convenient USB-C connection. KEY FEATURES: - RDM, ArtNet and sACN support - Factory and user presets for plug and play setups - POE or USB-C powered - 1.5” OLED Display with rotary knob - Rem ...

ELECTRICAL CONNECTIONS A qualified electrician should be used for all electrical connections and/or installations. USE CAUTION WHEN POWER LINKING OTHER MODEL DEVICES AS THE POWER CONSUMPTION OF OTHER MODEL DEVICES MAY EXCEED THE MAXIMUM POWER OUTPUT OF THIS DEVICE. CHECK SILK SCREEN FOR MAXIMUM AMPS. Device MUST be installed following all local, national, and country commercial ...

of the clamp (not included), and then thread it into the matching 10M hole on top, or 12M hole on bottom. The bolt must be threaded at least 18mm (0.7ins) into the fixture base. M12 M10 A Truss Clamp can be installed on top (10M) or bottom (12M) of EP2 Fixture. ...

control surface panel to the integrated multi-use mounting-bracket and lift. A qualified technician/electrician can then disconnect the data and power connectors from the control surface panel to the mounting case. Wall-Mount/Panel Installation: Chassis Disassembly 2. Remove the (4x) hex-screws securing the integrated multi-use mounting-bracket to the mounting case. This will be used to mount ...

1. Mount and secure the internal multi-use mounting- bracket to the junction-box. All wiring and connections must be performed by a qualified electrician. 2. Secure the control panel to the internal multi-use mounting-bracket with the (4x) torx-screws. ...

2. Secure the control panel to the internal multi-use mounting-bracket with the (4x) torx-screws. All wiring and connections must be performed by a qualified electrician. 1. Mount and secure the internal multi-use mounting- bracket to the junction-box. ...

To reconfigure the EP2 to its original form, remount the internal multi-use mounting-bracket to the case and secure it with (4) hex-screws. All wiring and connections must be performed by a qualified electrician. Once a qualified technician/electrician has reconnected the control surface panel with the power and data connectors, the control surface panel can then be mounted and ...

DMX CONNECTIONS: All DMX Output connections are 5pin female XLR; the pin-out on all sockets is pin 1 to shield, pin 2 to cold (-), and pin 3 to hot (+). Pins 4 and 5 are not used. Carefully connect DMX cables to the respective ports. To prevent damaging the DMX ports, provide strain relief and support. Avoid connecting FOH Snakes to the ports directly ...

DMX PORTS GREEN DMX In DMX Lost DMX PORTS BLUE DMX Out Stable DMX Lost DMX PORTS WHITE Flash on RDM packets DMX PORTS STATUS INDICATOR LEDs CONNECTIONS: FRONT & SIDE PANELS FRONT CONNECTIONS: (2) 5Pin DMX ports are bidirectional for In-and-Output DMX Port Status Indicator LED RJ45 Network connection w/POE Power: Type-C: 5V, 2A No Data Connection SIDE CONNECTIONS Menu return button Turn to scr ...

service is occasional cleaning. For other service-related concerns, please contact your Obsidian Control Systems dealer, or visit www.obsidiancontrol.com. Any service that is not described in this guide must be carried out by a trained and qualified Obsidian Control Systems technician. As any computer, the EP2 requires periodic cleaning. The s ...

Side - (1) Locking RJ45 Ethernet network connections (POE), USB-C power option (5V, 2A) Physical - Length: 4.6 in. (117.6mm) - Width: 4.5 in. (114mm) - Height: 3.5 in. (89mm) - Weight: 1.76lbs. (0.8kg) Electrical - USB-C 5V - POE 802.3af - Approvals / Ratings - CE / IP20 Included Items - Universal 5V/2A USB Power Adapter ...