Crown FM1000A Operation & User’s Manual
Text of Crown FM1000A Operation & User’s Manual
Crown FM1000A RF Amplifier Package
User's Manual
©2005 Crown Broadcast, a division of International Radio and Electronics, Inc.
25166 Leer Drive, Elkhart, Indiana, 46514-5425 U.S.A.
(574) 262-8900
®
Initial Release (Rev. 0) 900413-1
November 1998
Revision 1
April 2002
Important Notices
©2005, Crown Broadcast, a division of International Radio and Electronics, Inc.
All rights reserved. No part of this publication may be reproduced, transmitted,
transcribed, stored in a retrieval system, or translated into any language in any
form by any means without the written permission of Crown International, Inc.
Printed i
Section 1—Getting Acquainted
1.1 Your Amplifier Package .......................................................................................1–2
1.2 Amplifier Package Specifications.........................................................................1–3
1.3 Safety Considerations ..........................................................................................1–4
1.3.1 Dangers .........
PS1000 Power Supply ......................................................................................4–4
4.2.1
AC Input Board .............................................................................................4–5
4.2.2
PFC (Power Factor Correcting) Switching Board ..........................................4–5
4.2.3
DC Output Board ..........................................................................................4–6
4.2
Section 1—Getting Acquainted This section provides a general description of the FM1000A
power amplifier system and introduces you to safety conventions
used within this document. Review this material before install-
ing or operating the amplifier and power supply.
Crown FM1000A FM1000A User’s Manual
I
1–2
1.1 Your Amplifier Package
The FM1000A is a highly efficient amplifier package designed to set a new standard
in FM transmitter design offering modularity, ease of use, and long-term reliabil-
ity. The FM1000A package includes a PA1000 amplifier, PS1000 power supply, and
an FM1K accessory pack.
The PA1000 broadband amplifier requires no tuning and typically provides 80% RF
efficiency across the band. The PS1000 power suppl
1.2 Amplifier Package Specifications
RF Power Output:
100 to 1100 watts continuous with remote
controlled power adjust
RF Drive Requirement:
30 watts for full output
RF Output Impedance:
50 ohms (unbalanced)
Maximum SWR:
1.7:1 (With power foldback at high SWR)
Frequency Range:
87–108 MHz
RF Harmonics/Spurious Products:
Better than –80 dB
Asynchronous AM S/N Ratio:
Better than –55 dB with 100% modulation at
400 Hz, no de-empha
FM1000A User’s Manual I
1–4
1.3 Safety Considerations
Crown Broadcast assumes the responsibility for providing you a safe product and
safety guidelines during its use. “Safety” means protection to all individuals who
install, operate, and service the transmitter as well as protection of the transmitter
itself. To promote safety, we use standard hazard alert labeling on the product and
in this manual. Follow the associated guidelines to avoid pot
This section provides important guidelines for installing your
power amplifier and power supply. Review this information care-
fully for proper installation.
®
FM1000A User’s Manual 2.1
Operating Environment
You can install the FM1000A amplifier system in a standard 19–inch component
rack or on a suitable surface such as a bench or desk. In any case, the area should
be as clean and well-ventillated as possible. The power supply must be installed
directly above or below the power amplifier (for the included dressed cables to
reach their respective connectors).
2.2
Tools Required
To install the power su
Power Amplifier Modules
The PA1000 incorporates four power amplifiers (two each in two modules). Due to
possible damage during shipment, the power modules have been removed. Follow
these steps to install the modules:
1. Remove the front panel of the PA1000 (four screws).
2. Taking ESD precautions (see page 2–2), unpack the power modules and place
them on your work area with the circuit sides up.
3. The warni
FM1000A User’s Manual WARNING
2.4.2
Hubble Twist Lock® Connector Wiring
Prepare the wiring for the Hubble Twist-Lock® connector in the following manner
before connecting to your AC power source:
1. Use round cord with a diameter of 0.385–0.780 inches (10–20 mm), Type SJ
12/3 – 10/3; Type S 16/3 – 10/3.
2. Select conductor size from your National Electrical Code®.
3. Slide the cover onto the cord. Remove insulation from cable and conduct
1. Mount the units in an appropriate 19–inch wide cabinet. The power supply
must be installed directly below the power amplifier for the included
cables to reach their respective connectors (see illustration 2–4 below).
Note: The PS1000 weighs approximately 40 pounds (18.1 kg); the
PA1000, approximately 43 pounds (19.5 kg). Use help to install.
2. Ensure that the PS1000 power switch is off, the circuit breakers of
FM1000A User’s Manual 2.6
Remote I/O Connection
LOCAL
MAXIMUM
+5V
LOCAL
POWER
ADJUST
MINIMUM
REMOTE
TANSMITTER
CONTROL
SW3
RAISE
SW4
LOWER
SW5
R62
Electro-
Control
Circuit
REMOTE
RAISE POWER
Pin 4
Remote I/O Conn.
REMOTE
LOWER POWER
Pin 15
Remote I/O Conn.
Illustration 2–5 Local and Remote Functions
The Remote I/O Connector on the back of the PA1000 allows remote control and
monitoring of Certain transmitter functions. There are three basic cont
Crown FM1000A For remote I/O (Input/Output) connection, connect your remote I/O cable from
your remote control location to the 25–pin (female) D-sub connector on the back
panel of the PA1000. The I/O Connector on the power amplifier is described in the
following diagram:
The Remote I/O Connector Pinout Table on the next page summarizes the Remote
I/O pin connections.
1
25
13
14
View from Rear of Cabinet
Illustration 2–7 Remote I/O connector (back
FM1000A User’s Manual Remote I/O Connector Pinout Table
Pin #
Function
1
PA#8 Current Monitor (a buffered metering output with 1 V = 2 A)
2
PA#7 Current Monitor (a buffered metering output with 1 V = 2 A)
3
Ground
4
Remote RAISE Power (a momentary switch, on this pin, when held low will
raise the power level 10 watts every 0.5 seconds)
5
Remote RF Power Control (a resistor to ground on this pin reduces RF
power output level below internal limits.