Crown MICRO-TECH-1200 Reference Manual

Text of Crown MICRO-TECH-1200 Reference Manual

Crown MICRO-TECH-1200 Micro-Tech 600, 1200 & 2400

Micro-Tech 601, 1201 & 2401 Some models may be exported under the name Amcron.® 102990-1 7/97 © 1997 by Crown International, Inc., P.O. Box 1000, Elkhart, IN 46515-1000 U.S.A. Telephone: 219-294-8000. Fax: 219-294-8329. Micro-Tech amplifiers are produced by the Professional Audio Division of Crown International, Inc. Trademark Notice: Grounded bridge™ is a trademark and A

SUMMARY OF WARRANTY

The Crown Audio Division of Crown International, Inc., 1718 West Mishawaka Road, Elkhart, Indiana 46517-4095 U.S.A. warrants to you, the ORIGINAL PURCHASER and ANY SUBSEQUENT OWNER of each NEW Crown1 product, for a period of three (3) years from the date of purchase by the original purchaser (the “warranty period”) that the new Crown product is free of defects in materials and workmanship, and we further warrant the new Cr

WATCH FOR THESE SYMBOLS:

The lightning bolt triangle is used to alert the user to the risk of electric shock. The exclamation point triangle is used to alert the user to important operating or maintenance instructions. WARNING TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE! Magnetic Field CAUTION! Do not locate sensitive high-gain equip- ment such as preamplifiers or tape decks directly ab

Micro-Tech 600/1200/2400 Power Amplifiers

CONTENTS 1 Welcome .......................................................................... 7 1.1 Unpacking ................................................................. 7 1.2 Features .................................................................... 7 2 Facilities .......................................................................... 8 3 Installation ...........................................
Micro-Tech 600/1200/2400 Power Amplifiers ILLUSTRATIONS 1.1 Micro-Tech Amplifier .................................................................. 7 2.1 Front Facilities ............................................................................ 8 2.2 Rear Facilities ............................................................................ 9 3.1 Mounting Dimensions .............................................................. 10 3.2 Top View
Micro-Tech 600/1200/2400 Power Amplifiers 1 Welcome Congratulations on your purchase of a Micro-Tech® professional power amplifier. Crown’s Micro-Tech 600, 1200 and 2400 are the original industry standards for touring amplifiers. Micro-Tech amplifiers are known around the world as a the benchmark for high-density, ultra-pure power in a compact, lightweight package. In addition, each model gives you Crown’s legendary ODEP® protection to keep t
Micro-Tech 600/1200/2400 Power Amplifiers Fig. 2.1 Front Facilities ODEP CH1 CH2 POWER OFF A B C C D 2 Facilities A. Filter Grille This metal grille supports and protects the dust filter (B). To clean the dust filter, detach the grille by removing the three screws that hold it in place. B. Dust Filter The dust filter removes large particles from the air drawn by the cooling fan. Check the filter regularly to prevent clogging (see Sections 3.2 and
Micro-Tech 600/1200/2400 Power Amplifiers Fig. 2.2 Rear Facilities CAUTION: THIS COVER IS NECESSARY FOR EFFICIENT COOLING OF THE AMPLIFIER. REMOVE ONLY TO ACCESS GAIN SWITCH. 0 1 2 3 4 5 6 7 8 9 10 11 12 0 1 2 3 4 5 6 7 8 9 10 11 12 BRIDGE-MONO WIRING TURN AMPLIFIER OFF. SET STEREO/MONO SWITCH TO BRIDGE-MONO. OUTPUT ACROSS RED TERMINALS ONLY. (CH-1 IS POSITIVE.) PARALLEL-MONO WIRING TURN AMPLIFIER OFF. SET STEREO/MONO SWITCH TO PARALLEL-MONO. ADD
Micro-Tech 600/1200/2400 Power Amplifiers 3 Installation 3.1 Mounting Micro-Tech amplifiers are designed for standard 19- inch (48.3 cm) rack mounting or stacking without a cabinet. In a rack, it is best to mount units directly on top of each other. This provides the most efficient air flow and support. If the rack will be transported, we recommend that you provide support for the amplifier’s back panel or secure it to the rack to help support t
Micro-Tech 600/1200/2400 Power Amplifiers the rack so it blows outside air into the space between the door and the front of the amplifiers. This will pres- surize the “chimney” behind the door (Figure 3.3, Op- tion 1). The blower should not blow air into or take air out of the space behind the amplifiers. For racks with- out a front door, you can evacuate the rack by mount- ing the blower at the top of the rack so air blows out the back (Figur
Micro-Tech 600/1200/2400 Power Amplifiers CAUTION: In Stereo mode, never tie the amplifier’s outputs directly together, and never parallel them with the output of another amplifier. Such connec- tions do not increase the output power and may acti- vate the protection circuitry to prevent overheating. 3.3.2 Bridge-Mono Operation Bridge-Mono mode is used to drive loads with a total impedance of at least 4 ohms (see Section 3.3.3 if the load is les
Micro-Tech 600/1200/2400 Power Amplifiers CAUTION: Only connect balanced equipment (meters, switches, etc.) to the Bridge-Mono output. Both sides of the line must be isolated from the in- put grounds or oscillations may occur. 3.3.3 Parallel-Mono Operation Parallel-Mono mode is used to drive loads with a total impedance of less than 4 ohms (see Section 3.3.2 if the load is 4 ohms or more). Installing the amplifier in Parallel-Mono mode is very dif
Micro-Tech 600/1200/2400 Power Amplifiers 3.3.4 Input Connection The balanced phone jack inputs have a nominal im- pedance of 20 K ohms (10 K ohms with unbalanced wiring) and will accept the line-level output of most de- vices. Three-pin female XLR connectors are also avail- able on the optional MT-XLR accessory and balanced barrier block connectors are available on the optional MT-BB accessory (see Section 8.2). Correct input wir- ing will depend
Micro-Tech 600/1200/2400 Power Amplifiers SOLVING INPUT PROBLEMS Sometimes large subsonic (subaudible) frequencies are present in the input signal. These can damage loudspeakers by overloading or overheating them. To attenuate such frequencies, place a capacitor in se- ries with the input signal line. The graph in Figure 3.10 shows some possible capacitor values and how they affect frequency response. Use only low-leakage pa- per, mylar or tantalu
Micro-Tech 600/1200/2400 Power Amplifiers conductors that could bisect the magnetic field. Ground loops will also occur when the input and out- put grounds are tied together. DO NOT CONNECT THE INPUT AND OUTPUT GROUNDS TOGETHER. Tying the input and output grounds together can also cause feedback oscillation from the load current flowing in the loop. To avoid this problem use proper grounding, isolate the inputs, and isolate other common AC de- vic
Micro-Tech 600/1200/2400 Power Amplifiers 1. Note the load resistance of the loudspeakers connected to each channel of the amplifier. Mark this value on the “Load Resistance” line of the nomograph. 2. Select an acceptable damping factor and mark it on the “Damping Factor” line. Your amplifier can provide an excel- lent damping factor of 1,000 from 10 to 400 Hz in Stereo mode with an 8 ohm load. In contrast, typical damping fac- tors are 50

Crown Amplifier Owners Instructions: