Crown Pulse 21100 Operation & User’s Manual
Text of Crown Pulse 21100 Operation & User’s Manual
C o n t e n t s
Safety Information .................................................................................. 3
1.0 Introduction & Unpacking .................................................................... 4
2.0 Mechanical Installation ........................................................................ 5
3.0 AC Power Connection ......................................................................... 6
4.0 Audio Connections .............
DO NOT REMOVE COVERS. NO USER
SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE
PERSONNEL.
THIS EQUIPMENT MUST BE GROUNDED. IT
SHOULD NOT BE NECESSARY TO REMOVE ANY
PROTECTIVE GROUND OR SIGNAL CABLE
SHIELD CONNECTIONS TO PREVENT GROUND
LOOPS. ANY SUCH DISCONNECTIONS ARE
OUTSIDE THE RECOMMENDED PRACTICE OF
CROWN AND WILL RENDER ANY EMC OR
SAFETY CERTIFICATION VOID.
For continued compliance with international
EMC legislation ensure that all in
I n t r o d u c t i o n & U n p a c k i n g
Front panel
Rear panel
Introduction
The PULSE series of amplifiers are high performance professional power amplifiers capable of delivering
major power output from a new generation of switched mode power supplies. All Pulse series amplifiers are
housed in the same size 2U cases and feature light, powerful switching power supplies along with massive
heatsinks and two dual-speed cooling fans. Microproce
M e c h a n i c a l
I n s t a l l a t i o n
A vertical rack space of 2U
(88mm high) is required,
with an in rack depth of
18.1 inches (460mm).
The amplifier protrudes
1.6 inches (40mm) from
the rack supports.
If the unit is likely to undergo extreme vibration through trucking and touring, front rack ear reinforcement
brackets and rear mounting plates must be fitted. These are available from your dealer. Damage caused by
insufficient support is not
A C P o w e r C o n n e c t i o n
WARNING! THIS APPLIANCE MUST BE GROUNDED.
The amplifier must always be connected to a 3-wire grounded AC outlet. The rack framework must also be
connected to the same grounding circuit. The unit must NOT be operated unless the power cables' ground
wire is properly terminated - this is important for personal safety as well as for proper control over the
system grounding.
The wires in the power lead are color coded
For each channel, there is a 1/4” phone jack socket, male & female XLR and pluggable removable terminal
block connectors provided for signal input on the rear panel of the amplifier. Each is electronically balanced
at an impedance greater than 10k ohms.
The removable terminal block, phone jack and both XLR connectors are internally wired in parallel, and
therefore any socket may be used for the input signal. The connectors not used in this manne
Both binding post and Speakon
® connectors are provided
for each channel, these are internally wired in parallel
so either or both may be used. Note that it is possible
to lever the caps out of the ends of the binding posts to
insert 4mm banana type plugs but this will invalidate
the product safety approvals in some territories. The
side entry positions for these connectors should
therefore be used if possible.
Stereo operation
If you are using
Crown Pulse 21100 C o n t r o l
o p e r a t i o n
a. Power Switch
Pressing this switch so that the
white dot is closest to the front
panel signals to the
microprocessor that the user
wishes to turn on the power
supply. Note that the
microprocessor will only switch
the power supply on once it has
assured that there are no
internal faults. From the first
application of AC power it
takes approximately 7 seconds
to complete these tests. During
the test time the micropro
I n d i c a t o r s
A. AC Present
This light glows when AC power is applied to the amplifier, whether or not the amplifier is actually running.
This light will still glow even if the rear panel fuse is blown because it is powered from the separate,
internally fused supply that powers the microprocessor.
B. Operate
Illuminated when the main power supply is switched on using the front panel switch.
C. Fault
If, for any reason, the microprocessor det
I n d i c a t o r s . . .
F. Clip
This light is in fact rather more sophisticated than a simple clip indicator; it actually measures distortion.
This may occur either due to clipping, trying to drive too low an impedance speaker load or any other
mechanism that causes the output of the amplifier channel to not be as expected by the monitoring circuit.
Note that if the amplifier channel is muted by the microprocessor and a signal is applied, the clip lig
Crown Pulse 21100 T y p i c a l
a p p l i c a t i o n s
a. Two channel (stereo) operation
In this example, each channel of the PULSE 2x1100 is being used independently. For this application, ensure
that the rear panel BRIDGE switches are in the NORMAL position. More than one speaker may be used on
each channel as long as the total impedance is not less than 2 ohms. See section d for more information
about how to calculate impedance.
b. Two amplifiers used in bridge
T y p i c a l a p p l i c a t i o n s . . .
c. Two amplifiers for stereo with a mono sub-bass
Here Two amplifiers are used with an active crossover to provide a separate sub-bass signal.
d. Calculating Impedance
Measured in ohms, impedance is a measure of AC resistance. Loudspeakers generally come in 16, 8 or 4
ohm varieties. Amplifiers have a lower limit to what impedance they can drive without being overloaded,
there is not usually an upper limit. The
G l o s s a r y
In this section many of the terms used throughout this manual are explained in more detail.
Active
Active electronic circuits are those which are capable of voltage and power gain by using transistors and
integrated circuits.
Amplitude
Refers to the voltage level or intensity of a signal, and is usually measured in volts or decibels.
Balanced
A three wire connection in which two of the wires carry the signal information, the third
G l o s s a r y . . .
dBu or dBv
The addition of a lower case ”u” or “v” after dB indicates an absolute scaling for the dB ratio. 0dBu (or 0
dBv) = 778mV or 0.778 Volts, and it has no regard for power or impedance. This term is widely used for
expressing signal voltages in modern audio equipment with high input impedances and low output
impedances. For dBv the same scale is used as for dBu above, except that 0dBV = 1.0 Volts.
Distortion
Any modi
G l o s s a r y . . . Removable terminal block
One of the names given to a pluggable terminal block suitable for use with audio where connection to
permanent wiring makes their use more suitable than XLR or Jack connectors.
Transient
A sudden burst of energy in an audio signal which only lasts for a small period of time relative to the rest of
the signal. The level of these transients can often reach 10 times (+20dB) or so above the normal operating
lev
S p e c i f i c a t i o n s
Power Ratings
Pulse 2x1100
Stereo
Measured per channel, both channels driven at 1kHz to no more than 0.1% THD+N
8 ohms
700W rms
4 ohms
1100W rms
2 ohms
1500W rms*
* Note: 2 Ohm spec is at 1% THD
Bridged Mono
16 ohms
1200W rms
8 ohms
2200W rms
4 ohms
3000W rms*
* Note: 4 Ohm bridged spec is at 1% THD
Input Sensitivity
+1dBu for full output
Input Impedance
20 kohm
Input Connectors
1/4-inch TRS balanced phone jack, removab
Crown Pulse 21100 T r o u b l e s h o o t i n g
Checklist
Problem:
No output
Check:
Are the AC Present and Operate lights on?
Are the Fault & Temp lights off?
Are the Signal lights on?
Are the level controls turned up?
Are the speakers properly connected? (in particular check that older style ‘ring lock’ type
Speakons are rotated in the socket).
Problem:
Distorted sound
Check:
Are the Clip lights on?
Is any equipment before the amp being over driven?
Are any
T r o u b l e s h o o t i n g . . .
Status Indication
There is a microprocessor inside each PULSE amplifier responsible for monitoring all critical systems. The
status of which are displayed on the front panel lights.
Their indication is as follows:
Fault and both Temp lights flashing
The amplifier has just been plugged in and the microprocessor is carrying out a test sequence. This is
normal and will stop after about 7 seconds.
Power light on, Operate
Crown amplifiers are quality units that rarely require
servicing. Before returning your unit for servicing,
please contact Crown Technical Support to verify the
need for servicing.
This unit has very sophisticated circuitry which should
only be serviced by an authorized Crown Service Center..
This is one reason why each unit bears the following
label:
CAUTION: To prevent electric shock, do
not remove covers. No user serviceable
parts inside. Refer serv