6
Chapter 1 Introduction
This user’s manual is dedicated to MT850, a portable 2D scanner that can send data to the host
up to 20 meters away. This economical, ergonomic pocket-sized wireless 2D barcode scanner is
a high efficient companion for users who work with laptops, tablets, smart phones and other
mobile devices with iOS®, Android® and Windows®.
Specifications
Optic & Performance
Light Source
White LED
Visible red LED
Sensor
1280 x 800
Scan Rate
120 Frames/Sec
Resolution
3mil / 0.075mm
Scan Angle
Horizontal 40°
Vertical 30°
Pitch Angle
±60°
Skew Angle
±50°
Roll Angle
360°
Print Contrast Ratio
20%
Width of Field
141mm (13Mil Code39)
Memory
2MB (20,000 barcodes)
Scan Button
(Trigger)
LED Indicator
Exit Window
Micro USB port
(with protective cover)
Function Button
(iOS Hotkey Button)
(Delete Button)
MT850 User’s Manual V1.3
7
Guaranteed D.O.F
(Environment: 800 lux)
3 Mil Code 39 : 65 ~ 95mm
5 Mil Code 39 : 35 ~ 155mm
13 Mil UPC/EAN : 45 ~ 285mm
15 Mil QR Code : 40 ~ 210mm
6.67 Mil PDF417 : 50 ~ 145mm
10 Mil Data Matrix : 40 ~ 140mm
Physical Characteristics
Dimension
W42.5 x L102 x H21.5 mm
Weight
71g
Color
White
Material
PC
Cable
Micro(M) to USB A(M) Cable, 1.5M
Trigger
Scan Button (Trigger)
Function Button (iOS Hotkey/Delete Button)
Indicator
LED, Buzzer, Vibrator
Electrical
Operation Voltage
3.7 VDC ± 5%
Working Current
< 330mA
Standby Current
< 60mA
Battery
3.7V, 1000mAh, Li-Polymer Battery
Number of Scan
(per full charge)
> 10,000 scans
(1 scan/ 5 secs, Bluetooth connected)
Connectivity
Radio
Bluetooth 5.0 dual mode (Class 2)
Range
66 ft/ 20m (line of sight)
Interface/ Profile
BT HID
BT SPP
USB HID
USB VCP
Memory
User Environment
Operating Temperature
-10 ~ 50˚C
Storage Temperature
-20 ~ 60˚C
Humidity
0% ~ 95%RH (Non-condensing)
Drop Durability
1.5M
Sealing
IP55
Ambient Light
70,000 Lux (Sunlight)
1D Symbologies
UPC-A/ UPC-E, EAN-8/ EAN-13, Code128,
GS1-128, Code 39, Code32, Code 93,
Code11, Interleaved 2 of 5, Matrix 2 of 5,
MT850 User’s Manual V1.3
8
Industrial 2 of 5, Codabar, MSI, GS1 Databar
2D Symbologies
QR Code, Micro QR Code, Data Matrix,
PDF417, MicroPDF417, Aztec
Regulatory
ESD
Functional after 4KV contact, 8KV air
discharge
EMC/RF
TBA
Safety Approval
TBA
Environmental
WEEE, RoHS 2.0
Medical Compliance
ISO 22196 (JIS Z 2801), ISO 11737-1/2
Beeper Indication
Beeper
Status
Single beep
Good read
Single short beep
The scanner reads a Code39 ASCII during
multi-step configuration
Two beeps
Wireless connection
The scanner successfully reads a
configuration barcode
Three beeps
Wireless disconnection
Three short beeps
The scanner reads a barcode while
disconnected
The scanner reads an unexpected barcode
during multi-step configuration. (Please
scan “Abort” and start over)
Memory Full
Four beeps (Hi-Lo-Hi-Lo)
Out of range / Poor connection
Five beeps
Low power
LED Indication
LED
Status
Off
Power off / Standby / Connected
Flashing blue
Disconnected / Discoverable
MT850 User’s Manual V1.3
10
Chapter 2 General Settings
Barcode Configurability
Scanning below configuration barcodes will allow/prohibit user to change settings by scanning
configuration barcodes in this manual.
Enable Barcode Configurability*
Disable Barcode Configurability
Factory Default
Scanning below configuration barcode will reset all parameters to factory default settings (the ones
with * asterisk mark)
Factory Default
Check Version
To check firmware version, please scan below configuration barcode.
Check Version
MT850 User’s Manual V1.3
11
Good Read Indicator
Beep Tone
Off
Beep Low (2.0KHz)
Beep Medium (2.7KHz)
Beep High (4.0KHz)*
Beep Mode
Normal*
Warning Beep Only
Mute
Vibrator
Off*
On
MT850 User’s Manual V1.3
12
Data Format
UTF-8 to Unicode Conversion
Off*
On
HT/CR/ESC Converts to TAB/ENTER/ESCAPE
Off*
On
Note:
1. By default, HT [$I], CR [$M] and ESC [%A] is transmitted as <0x09>, <0x0D> and <0x1B>
respectively.
2. When enabled, HT [$I], CR [$M] and ESC [%A] is transmitted as , and
on keyboard respectively.
Function Code Conversion
Off
On*
MT850 User’s Manual V1.3
13
Note:
Once disabled, the scanner will output the original encoded data of the barcodes in Appendix –
Function/Navigation/Modifier Keys.
Numeric Key
Numeric Key
Alphanumeric Key*
Note:
1. By default, the alphanumeric key is used for 13ecommended13 digits. Scan NUMERIC KEY if
you want to use the keys on the numeric keypad.
2. If you select NUMERIC KEY, the Num Lock status of the physical keyboard should be ON.
Capslock Mode
Capslock Off*
Capslock On
Capslock Free
Note:
When barcode scanner is set to Capslock Free mode, no matter keyboard Capslock LED indicator
is ON or OFF, output will be always the same as the Original barcode. In other words, what you see
is what output is.
MT850 User’s Manual V1.3
14
Keyboard Layout
English (US)*
English (UK)
Danish
Spanish
Hungarian (QWERTZ)
Hungarian (QWERTY)
Canadian French
Dutch
Italian
French
German
Swiss German
MT850 User’s Manual V1.3
15
Swiss French
Swedish
Czech (QWERTZ)
Czech (QWERTY)
Norwegian
Belgian
Portuguese
Slovak
Brazilian (QWERTY)
Canadian (Traditional)
Japanese
Alt Code
MT850 User’s Manual V1.3
16
Intercharacter Delay
The configurable range is from 0 to 255ms. The larger the number, the longer the delay.
Set Intercharacter Delay
(Default = 10ms)
Example: Set Intercharacter Delay to 8ms
Step1: Scan Set Intercharacter Delay
Step2: Scan “0” “0” “8” in Appendix – Numbers
Step3: Scan Set Intercharacter Delay
Interblock Delay
The configurable range is from 0 to 2550ms. The larger the number, the longer the delay.
Set Interblock Delay
(Default = 0ms)
Example: Set Interblock Delay to 20ms
Step1: Scan Set Interblock Delay
Step2: Scan “0” “0” “2” in Appendix – Numbers
Step3: Scan Set Interblock Delay
MT850 User’s Manual V1.3
17
BCC (Binary Check Character)
On
Off*
Note:
Once enabled, a checksum will be added to the end of each data to conduct Xor calculation. For
Bluetooth SPP & USB VCP, the BCC is 1 byte. For Bluetooth HID & USB HID the BCC are 2 bytes.
Example:
The barcode data is “TEST” with terminator
Chapter 1 BT SPP & USB VCP:
Data Format = + + + + + + .
BCC = 54h ^ 45h ^ 53h ^ 54h ^ 0Dh ^ 0Ah = 11h
2. BT HID & USB HID:
Data Format = + + + + +
BCC = 54h ^ 45h ^ 53h ^ 54h ^ E7h = F1h
However, since control character cannot be displayed in Bluetooth HID & USB HID, BCC will be
converted into 2 bytes of characters.
As a result, the data will be: TEST + + F + 1
Imaging Settings
Inverse Barcode
Disable Inverse Barcode*
Enable Inverse Barcode
MT850 User’s Manual V1.3
18
Centering
Disable Centering*
Enable Centering
Note:
When enabled, the scanner only decodes the barcodes marked by aimer dot.
MT850 User’s Manual V1.3
19
Chapter 1 Interface
BT HID
Getting Connected
1. Press the scan button to power up the scanner.
2. Scan “Disconnect”, the scanner will emit two beeps. Alternatively you may press and hold
function for 5 seconds until two beeps.
Disconnect
3. Scan “BT HID”, the scanner will emit two beeps.
BT HID
4. Select “Wireless Scanner” from discovered device list.
5. If Bluetooth application prompts you to enter a pincode, please follow the steps in Pincode
Setup section.
6. The scanner will emit two beeps as indication that the Bluetooth connection has established
successfully.
7. While conneted with the scanner as physical keyboard, the touch keyboard on iOS/Android
device might disappear. To resolve this issue please do the following:
(1) For iOS device, simply press the function button once.
(2) For Android device, go to “Settings” > “Language & Input”, tap on “Default keyboard” and
turn off “Physical keyboard” or turn on “On-screen keyboard”.
MT850 User’s Manual V1.3
20
Pincode Setup
If Bluetooth application prompts you to enter a pincode, please follow the steps:
1. Scan “Pincode Start”
Pincode Start
2. Scan numeric barcodes below according to the pincode generated by the Bluetooth application.
0
1
2
3
4
5
6
7
8
9
3. Scan “Enter”
Enter
MT850 User’s Manual V1.3
21
4. Scan “Pincode Stop”
Pincode Stop
BT SPP
Getting Connected
1. Press the scan button to power up the scanner.
2. Scan “Disconnect”, the scanner will emit two beeps.
Disconnect
3. Scan “BT SPP Master”(21ecommended) or “BT SPP Slave”, the scanner will emit two beeps. If
host can’t auto-reconnect, use BT SPP Master. If host can auto-reconnect, use BT SPP Slave
to avoid conflict.
BT SPP Master
(Auto-reconnect)
BT SPP Slave
(No Auto-reconnect)
4. Select “Wireless Scanner” from discovered device list.
5. If Bluetooth application prompts you to enter a pincode, enter “1234” from the host.
6. Enter serial communication software on your host and open the port occupied by the scanner.
7. The scanner will emit two beeps as indication that the Bluetooth connection has established
successfully.
MT850 User’s Manual V1.3
22
Set SPP Pincode
By default, the pincode under BT SPP profile for the scanner is “1234”. It is configurable up to 8
numbers.
Set SPP Pincode
Example: Set SPP Pincode to 0000.
Step1: Scan “Set SPP Pincode”
Step2: Scan “0” “0” “0” “0” in Appendix – Numbers
Step3: Scan “Set SPP Pincode”
MT850 User’s Manual V1.3
23
General Bluetooth Settings
Power Off Timeout
The power off timeout is 3 minutes & 0 second by default. They are configurable from a minimum of
10 seconds (00:10) to a maximum of 60 minutes and 59 seconds (60:59)
Set Minute
(Default = 03)
Set Second
(Default = 00)
Example: Set Power Off Timeout to 5 minnutes and 30 seconds.
Step1: Scan “Set Minute”
Step2: Scan “0” “5” in Appendix – Numbers
Step3: Scan “Set Minute”
Step4: Scan “Set Second”
Step5: Scan “3” “0” in Appendix – Numbers
Step6: Scan “Set Second”
To disable Power Off Timeout (make scanner always on), scan below barcode:
Disable Timeout
MT850 User’s Manual V1.3
24
Set Bluetooth Device ID
Bluetooth device name is configurable up to 16 alphanumeric characters:
Set Bluetooth Device ID
Example: Set XYZ123 as Bluetooth Device ID
Step 1: Scan “Set Bluetooth Device ID”
Step 2: Scan “X” “Y” “Z” “1” “2” “3” in Appendix – Upper Case Alphabets & Numbers
Step 3: Scan “Set Bluetooth Device ID”
To reset Bluetooth Device ID to “Wireless Scanner”, scan below barcode:
Reset Bluetooth Device ID
Check Bluetooth Firmware Version
Check Bluetooth Firmware Version
MT850 User’s Manual V1.3
25
Check Device MAC Address
Check Device MAC Address
Check Host MAC Address
Check Host MAC Address
ScanLink
ScanLink is a connection method that turns the scanner into a master device, which initiates the
Bluetooth connection with the target host device (now a slave device). This, as a result, saves user
the trouble of going through numerous setup procedures on the host device to establish
connection.
Simply generate ScanLink barcode for the target slave device in below rule:
For BT HID profile, please encode:
HID in Code39 without checksum or QR Code.
For BT SPP profile, please encode:
SPP in Code39 without checksum or QR Code.
Example: Target Slave Device MAC Address = 00:15:83:52:2C:3B, Profile = BT HID
Encode HID001583522C3B in Code39 without checksum or QR Code.
MT850 User’s Manual V1.3
26
Memory Mode
Memory Mode
After scanning the above barcode, the scanner will be able to collect barcode data off-line. The
barcode data will be stored in the format of:
,
MT850 User’s Manual V1.3
27
Data Format
The default Data Format in memory mode is ,
MT850 User’s Manual V1.3
28
Date Format
The default Date Format is DD/MM/YYYY (Code = 09)
Date Format
Below are available Date Format and their setup codes:
Code Date Format
Code Date Format
01
DD-MM-YYYY
09
DD/MM/YYYY
02
MM-DD-YYYY
10
MM/DD/YYYY
03
DD-MM-YY
11
DD/MM/YY
04
MM-DD-YY
12
MM/DD/YY
05
YYYY-MM-DD
13
YYYY/MM/DD
06
YY-MM-DD
14
YY/MM/DD
07
DD-MM
15
DD/MM
08
MM-DD
16
MM/DD
Example: Set Date Format as MM/DD/YY (Code = 12)
Step1: Scan “Date Format”
Step2: Scan “1” “2” respectively in Appendix – Numbers
Step3: Scan “Date Format”
Time Format
The default Time Format is HH:MM:SS (Code = 01)
Time Format
Below are available Time Format and their setup codes:
Code
Time Format
01
HH:MM:SS
02
HH:MM
MT850 User’s Manual V1.3
29
Example: Set Time Format as HH:MM (Code = 02)
Step1: Scan “Time Format”
Step2: Scan “0” “2” respectively in Appendix – Numbers
Step3: Scan “Time Format”
Date & Time Setup
Set Date
Set Time
Example: Set date as 2021-07-27, set time as 08:10:30 am (HH:MM:SS)
Step1: Scan “Set Date”
Step2: Scan “2” “1” “0” “7” “2” “7” in Appendix – Numbers
Step3: Scan “Set Date”
Step4: Scan “Set Time”
Step5: Scan “0” “8” “1” “0” “3” “0” in Appendix – Numbers
Step6: Scan “Set Time”
MT850 User’s Manual V1.3
31
Chapter 4 Reading Mode
Trigger Mode
In Trigger Mode the LED will stay on once trigger is pressed and held, and will turn off automatically
once a barcode is read or LED Auto-Off timeout expires.
Trigger Mode*
Auto-sensing Mode
In Auto-sensing Mode the LED will turn off automatically after LED Auto-Off timeout expires. Any
change detected in image will make LED turn on again.
Auto-sensing Mode
MT850 User’s Manual V1.3
32
Chapter 5 Data Format
By default data format is as follows:
Code ID
Disable Code ID*
Enable Factory ID
Enable Set ID
Set ID
Set ID can be 0 ~ 2 alphanumerics for each symbology.
Set ID – Code39
Set ID – Codabar
Set ID – Interleaved 2 of 5
Set ID – Matrix 2 of 5
MT850 User’s Manual V1.3
33
Set ID – Industrial 2 of 5
Set ID – Code11
Set ID – MSI Plessey
Set ID – EAN-13
Set ID – UPC-A
Set ID – EAN-8
Set ID – UPC-E
Set ID – Code93
Set ID – Code128
Set ID – GS1 Databar
Set ID – QR Code
Set ID – Data Matrix
Set ID – PDF417
Set ID – MicroPDF417
MT850 User’s Manual V1.3
34
Set ID – Aztec
Example: Set Code39 Set ID as XY
Step1: Scan “Set ID – Code39”
Step2: Scan “X” “Y” in Appendix – Upper Case Alphabets
Step3: Scan “Set ID – Code39”
Data Length
Send Data Length Off*
Send Data Length On
Preamble
Preamble can be up to 16 bytes of data.
Set Preamble
Example: Set Preamble as XYZ123
Step 1: Scan “Set Preamble”
Step 2: Scan “X” “Y” “Z” “1” “2” “3” in Appendix – Upper Case Alphabets & Numbers
Step 3: Scan “Set Preamble”
MT850 User’s Manual V1.3
35
Postamble
Postamble can be up to 16 bytes of data.
Set Postamble
Example: Set Postamble as XYZ123
Step 1: Scan “Set Postamble”
Step 2: Scan “X” “Y” “Z” “1” “2” “3” in Appendix – Upper Case Alphabets & Numbers
Step 3: Scan “Set Postamble”
Clear Preamble/Postamble
Clear Preamble/Postamble
Terminator
None
*
*
MT850 User’s Manual V1.3
36
Note:
1. For USB HID/BT HID interface the default terminator is CR.
2. For USB VCP/BT SPP interface the default terminator is CR+LF
MT850 User’s Manual V1.3
37
Chapter 6 Symbologies
General Settings
Enable All Symbologies
Disable All Symbologies
Enable All 1D Symbologies
Disable All 1D Symbologies
Enable All 2D Symbologies
Disable All 2D Symbologies
Note: When all symbologies are disabled, configuration barcodes are still readable.
UPC-A
Enable/Disable UPC-A
Enable UPC-A*
Disable UPC-A
MT850 User’s Manual V1.3
38
Check Digit
Send Check Digit*
Not Send Check Digit
UPC-A to EAN-13
Enable UPC-A to EAN-13
Disable UPC-A to EAN-13*
UPC-E0
Enable/Disable UPC-E0
Enable UPC-E0*
Disable UPC-E0
Check Digit
Send Check Digit*
Not Send Check Digit
MT850 User’s Manual V1.3
39
UPC-E0 to UPC-A
Enable UPC-E0 to UPC-A
Disable UPC-E0 to UPC-A*
EAN-8
Enable/Disable EAN-8
Enable EAN-8*
Disable EAN-8
Check Digit
Not Send Check Digit
Send Check Digit*
EAN-13
Enable/Disable EAN-13
Enable EAN-13*
Disable EAN-13
MT850 User’s Manual V1.3
40
Check Digit
Not Send Check Digit
Send Check Digit*
ISBN
On
Off*
ISSN
On
Off*
UPC/EAN Supplement
Enable 2/5-digit Supplement
Disable 2/5-digit Supplement*
Auto 2/5-digit Supplement
42
Code128/GS1-128 Min/Max Length
Set Min Length
(Default = 04)
Set Max Length
(Default = 50)
Example: Set Min Length as 8, Max Length as 12 for Code128/GS1-128
Step1: Scan “Set Min Length”
Step2: Scan “0” “8” in Appendix – Numbers
Step3: Scan “Set Min Length”
Step4: Scan “Set Max Length”
Step5: Scan “1” “2” in Appendix – Numbers
Step6: Scan “Set Max Length”
Note: Configurable range for Min/Max Length is 01 ~ 50.
MT850 User’s Manual V1.3
43
Code 39
Enable/Disable Code 39
Enable Code 39*
Disable Code 39
Verification
Disable CDV*
CDV & Send CD
CDV & Not Send CD
Start/Stop
Not Send Start/Stop*
Send Start/Stop*
MT850 User’s Manual V1.3
44
Full ASCII Code39
Enable Full ASCII Code39*
Disable Full ASCII Code39
Code39 Min/Max Length
Set Min Length
(Default = 01)
Set Max Length
(Default = 50)
Example: Set Min Length as 8, Max Length as 12 for Code39
Step1: Scan “Set Min Length”
Step2: Scan “0” “8” in Appendix – Numbers
Step3: Scan “Set Min Length”
Step4: Scan “Set Max Length”
Step5: Scan “1” “2” in Appendix – Numbers
Step6: Scan “Set Max Length”
Note: Configurable range for Min/Max Length is 01 ~ 50.
MT850 User’s Manual V1.3
45
Code 32
Enable/Disable Code 32
Enable Code 32
Disable Code 32*
Notw: Please make sure Code39 is enabled with verification disabled before enabling Code32.
Leading/Tailing
Not Send Leading & Tailing
Send Leading Only
Send Tailing Only
Send Leading & Tailing*
MT850 User’s Manual V1.3
46
Code 93
Enable/Disable Code 93
Enable Code 93*
Disable Code 93
Code 93 Min/Max Length
Set Min Length
(Default = 04)
Set Max Length
(Default = 50)
Example: Set Min Length as 8, Max Length as 12 for Code93
Step1: Scan “Set Min Length”
Step2: Scan “0” “8” in Appendix – Numbers
Step3: Scan “Set Min Length”
Step4: Scan “Set Max Length”
Step5: Scan “1” “2” in Appendix – Numbers
Step6: Scan “Set Max Length”
Note: Configurable range for Min/Max Length is 01 ~ 50.
48
Code 11 Min/Max Length
Set Min Length
(Default = 04)
Set Max Length
(Default = 50)
Example: Set Min Length as 8, Max Length as 12 for Code11
Step1: Scan “Set Min Length”
Step2: Scan “0” “8” in Appendix – Numbers
Step3: Scan “Set Min Length”
Step4: Scan “Set Max Length”
Step5: Scan “1” “2” in Appendix – Numbers
Step6: Scan “Set Max Length”
Note: Configurable range for Min/Max Length is 01 ~ 50.
MT850 User’s Manual V1.3
49
Codabar (NW-7)
Enable/Disable Codabar
Enable Codabar*
Disable Codabar
Start/Stop
Send Start/Stop
Not Send Start/Stop*
Codabar Min/Max Length
Set Min Length
(Default = 04)
Set Max Length
(Default = 50)
Example: Set Min Length as 8, Max Length as 12 for Codabar
Step1: Scan “Set Min Length”
Step2: Scan “0” “8” in Appendix – Numbers
Step3: Scan “Set Min Length”
Step4: Scan “Set Max Length”
Step5: Scan “1” “2” in Appendix – Numbers
Step6: Scan “Set Max Length”
Note: Configurable range for Min/Max Length is 01 ~ 50.
MT850 User’s Manual V1.3
50
Interleaved 2 of 5
Enable/Disable Interleaved 2 of 5
Enable Interleaved 2 of 5*
Disable Interleaved 2 of 5
Verification
Disable CDV*
CDV & Send CD
CDV & Not Send CD
MT850 User’s Manual V1.3
51
Interleaved 2 of 5 Min/Max Length
Set Min Length
(Default = 05)
Set Max Length
(Default = 50)
Example: Set Min Length as 8, Max Length as 12 for Interleaved 2 of 5
Step1: Scan “Set Min Length”
Step2: Scan “0” “8” in Appendix – Numbers
Step3: Scan “Set Min Length”
Step4: Scan “Set Max Length”
Step5: Scan “1” “2” in Appendix – Numbers
Step6: Scan “Set Max Length”
Note: Configurable range for Min/Max Length is 01 ~ 50.
MT850 User’s Manual V1.3
52
Matrix 2 of 5
Enable/Disable Matrix 2 of 5
Enable Matrix 2 of 5*
Disable Matrix 2 of 5
Matrix 2 of 5 Min/Max Length
Set Min Length
(Default = 04)
Set Max Length
(Default = 24)
Example: Set Min Length as 8, Max Length as 12 for Matrix 2 of 5
Step1: Scan “Set Min Length”
Step2: Scan “0” “8” in Appendix – Numbers
Step3: Scan “Set Min Length”
Step4: Scan “Set Max Length”
Step5: Scan “1” “2” in Appendix – Numbers
Step6: Scan “Set Max Length”
Note: Configurable range for Min/Max Length is 01 ~ 50.
MT850 User’s Manual V1.3
53
Industrial 2 of 5
Enable/Disable Industrial 2 of 5
Enable Industrial 2 of 5*
Disable Industrial 2 of 5
Industrial 2 of 5 Min/Max Length
Set Min Length
(Default = 04)
Set Max Length
(Default = 24)
Example: Set Min Length as 8, Max Length as 12 for Industrial 2 of 5
Step1: Scan “Set Min Length”
Step2: Scan “0” “8” in Appendix – Numbers
Step3: Scan “Set Min Length”
Step4: Scan “Set Max Length”
Step5: Scan “1” “2” in Appendix – Numbers
Step6: Scan “Set Max Length”
Note: Configurable range for Min/Max Length is 01 ~ 50.
.
55
MSI Plessey Min/Max Length
Set Min Length
(Default = 04)
Set Max Length
(Default = 50)
Example: Set Min Length as 8, Max Length as 12 for MSI Plessey
Step1: Scan “Set Min Length”
Step2: Scan “0” “8” in Appendix – Numbers
Step3: Scan “Set Min Length”
Step4: Scan “Set Max Length”
Step5: Scan “1” “2” in Appendix – Numbers
Step6: Scan “Set Max Length”
Note: Configurable range for Min/Max Length is 01 ~ 50.
57
QR Code
Enable/Disable QR Code
Enable QR Code*
Disable QR Code
Micro QR Code
Enable/Disable Micro QR Code
Enable Micro QR Code*
Disable Micro QR Code
Data Matrix
Enable/Disable Data Matrix
Enable Data Matrix*
Disable Data Matrix
64
Appendix – Control Codes
NUL
SOH
STX
ETX
EOT
ENQ
ACK
BEL
BS
HT
LF
VT
FF
CR
SO
SI
MT850 User’s Manual V1.3
69
Appendix – Function Keys
F1
F2
F3
F4
F5
F6
F7
F8
F9
F10
F11
F12
Home
End
Enter (Numeric Key)
App
MT850 User’s Manual V1.3
70
Appendix – Navigation Keys
Cursor Left
Cursor Right
Cursor Up
Cursor Down
Page Up
Page Down
Tab
Back Tab
Esc
Enter
BS
Ins
Del
MT850 User’s Manual V1.3
71
Appendix – Modifier Keys
Alt (Left) make *1
Alt (Left) break
Alt (Right) make
Alt (Right) break
Shift (Left) make *2
Shift (Left) break
Shift (Right) make
Shift (Right) break
Win (Left) make
Win (Left) break
Win (Right) make
Win (Right) break
MT850 User’s Manual V1.3
72
Ctrl (Left) make *3
Ctrl (Left) break
Ctrl (Right) make
Ctrl (Right) break
Note:
*1: When “Alt (Left) make” is programmed, please scan “Alt (Left) break” to resume barcode setting.
*2: When “Shift (Left) make” is programmed, please scan “Shift (Left) break” to resume barcode
setting.
*3: When “Ctrl (Left) make” is programmed, please scan “Ctrl (Left) break” to resume barcode
setting.
Appendix – Abort
If there is an error reading data barcode during multi-step configuration, you may cancel
configuration by scanning below configuration barcode.
Abort
MT850 User’s Manual V1.3
73
Appendix – Default Table
Function
Default
Remark
General Settings
Barcode Configurability
ON
Beep Tone
High (4.0KHz)
Beep Mode
Normal
Vibrator
OFF
Data Format
UTF-8 to Unicode Conversion
OFF
HT/CR/ESC Converts to
TAB/ENTER/ESCAPE
OFF
Function Code Conversion
ON
Numeric Key
Alphanumeric Key
Capslock Mode
OFF
Keyboard Layout
English (US)
Intercharacter Delay
10ms
Interblock Delay
0ms
BCC (Binary Check Character)
OFF
Image Settings
Inverse Barcode
OFF
Interface
BT HID
Getting Connected
N/A
BT SPP
Getting Connected
N/A
Set SPP Pincode
1234
General Bluetooth Settings
Power Off Timeout
03:00
Set Bluetooth Device ID
Wireless Scanner
Memory Mode
Data Format
,,
Field Separator
,
Date Format
DD/MM/YYYY
Time Format
HH:MM:SS
Date & Time Setup
N/A
USB HID
N/A
USB VCP
N/A
Reading Mode
MT850 User’s Manual V1.3
74
Trigger Mode
Trigger Mode
Auto-sensing Mode
N/A
Data Format
Code ID
Disable
Set ID
N/A
Data Length
OFF
Preamble
N/A
Postamble
N/A
Terminator
CR (BT HID / USB HID)
CR+LF (BT SPP / USB VCP)
Symbologies
General Settings
N/A
UPC-A
Enable/Disable
ON
Check Digit
Send
UPC-A to EAN-13
OFF
UPC-E0
Enable/Disable
ON
Check Digit
Send
UPC-E0 to UPC-A
OFF
EAN-8
Enable/Disable
ON
Check Digit
Send
EAN-13
Enable/Disable
ON
Check Digit
Send
ISBN
OFF
ISSN
OFF
UPC/EAN Supplement
OFF
Code 128
Enable/Disable
ON
GS1-128
Enable/Disable
ON
Min Length
04
Max Length
50
Code 39
Enable/Disable
ON
Verification
Disable CDV
Start/Stop
Not Send
Full ASCII Code39
ON
MT850 User’s Manual V1.3
75
Min Length
01
Max Length
50
Code 32
Enable/Disable
OFF
Leading/Tailing
Send Leading & Tailing
Code 93
Enable/Disable
ON
Min Length
04
Max Length
50
Code 11
Enable/Disable
OFF
Verification
Disable CDV
Check Digit
Not Send
Min Length
04
Max Length
50
Codabar
Enable/Disable
ON
Start/Stop
Not Send
Min Length
04
Max Length
50
Interleaved 2 of 5
Enable/Disable
ON
Verification
Disable CDV
Min Length
05
Max Length
50
Matrix 2 of 5
Enable/Disable
ON
Min Length
04
Max Length
24
Industrial 2 of 5
Enable/Disable
ON
Min Length
04
Max Length
24
MSI Plessey
Enable/Disable
OFF
Verification
Send Check Digit, Single Check
Digit MOD10
Min Length
04
Max Length
50
GS1 DataBar (RSS-14)
MT850 User’s Manual V1.3
76
Enable/Disable
ON
GS1 DataBar Limited (RSS-Limited)
Enable/Disable
ON
GS1 DataBar Expanded
(RSS-Expanded)
Enable/Disable
ON
QR Code
Enable/Disable
ON
Micro QR Code
Enable/Disable
ON
Data Matrix
Enable/Disable
ON
PDF 417
Enable/Disable
ON
Micro PDF 417
Enable/Disable
ON
Aztec
Enable/Disable
ON
MT850 User’s Manual V1.3
77
Appendix – Factory ID
#
Symbology
Code ID
HEX
0
UPC-E0
E
45
1
UPC-A
A
41
2
EAN-8
S
53
3
EAN-13
F
46
4
Code 128/GS1-128/ISBT 128
K
4B
5
Code 39/Code32
M
4D
6
Code 93
L
4C
7
Code 11
J
4A
8
Codabar
N
4E
9
Interleaved 2 of 5
I
49
10
Matrix 2 of 5
Y
59
11
Industrial 2 of 5
V
56
12
GS1 DataBar
G
47
13
MSI Plessey
O
4F
14
PDF 417
Z
5A
15
Micro PDF 417
r
72
16
Data Matrix
X
58
17
QR Code/Micro QR Code
W
57
18
Aztec
z
7A
MT850 User’s Manual V1.3
78
Appendix – ASCII Table
Note: ASCII 0~31 are non-printable characters, ASCII 32~127 are printable characters.
Hex
Dec
ASCII
00
00
NUL (Null char.)
01
01
SOH (Start of Header)
02
02
STX (Start of Text)
03
03
ETX (End of Text)
04
04
EOT (End of Transmission)
05
05
ENQ (Enquiry)
06
06
ACK (Acknowledgment)
07
07
BEL (Bell)
08
08
BS (Backspace)
09
09
HT (Horizontal Tab)
0A
10
LF (Line Feed)
0B
11
VT (Vertical Tab)
0C
12
FF (Form Feed)
0D
13
CR (Carriage Return)
0E
14
SO (Shift Out)
0F
15
SI (Shift In)
10
16
DLE (Data Link Escape)
11
17
DC1 (XON) (Device Control 1)
12
18
DC2 (Device Control 2)
13
19
DC3 (XOFF) (Device Control 3)
14
20
DC4 (Device Control 4)
15
21
NAK (Negative Acknowledgment)
16
22
SYN (Synchronous Idle)
17
23
ETB (End of Trans. Block)
18
24
CAN (Cancel)
19
25
EM (End of Medium)
1A
26
SUB (Substitute)
1B
27
ESC (Escape)
1C
28
FS (File Separator)
1D
29
GS (Group Separator)
1E
30
RS (Request to Send)
1F
31
US (Unit Separator)
20
32
SP (Space)
21
33
! (Exclamation Mark)
22
34
“ (Double Quote)
80
4B
75
K
4C
76
L
4D
77
M
4E
78
N
4F
79
O
50
80
P
51
81
Q
52
82
R
53
83
S
54
84
T
55
85
U
56
86
V
57
87
W
58
88
X
59
89
Y
5A
90
Z
5B
91
[ (Left / Opening Bracket)
5C
92
\ (Back Slash)
5D
93
] (Right / Closing Bracket)
5E
94
^ (Caret / Circumflex)
5F
95
_ (Underscore)
60
96
‘ (Grave Accent)
61
97
a
62
98
b
63
99
c
64
100
d
65
101
e
66
102
f
67
103
g
68
104
h
69
105
I
6A
106
j
6B
107
k
6C
108
l
6D
109
m
6E
110
n
6F
111
o
70
112
p
71
113
q
72
114
r
MT850 User’s Manual V1.3
81
73
115
s
74
116
t
75
117
u
76
118
v
77
119
w
78
120
x
79
121
y
7A
122
z
7B
123
{ (Left/ Opening Brace)
7C
124
| (Vertical Bar)
7D
125
} (Right/Closing Brace)
7E
126
~ (Tilde)
7F
127
DEL (Delete)
MT850 User’s Manual V1.3
82
Version History
Rev
Date
Description
Issued
1.0
2021.08.25
Initial Release
Shaw
1.1
2021.08.31
Revised configurable range for Min/Max length
Shaw
1.2
2021.10.05
Revised number of scan to > 10,000 scans
Shaw
1.3
2021.12.02
Updated Range to 66ft/20m
Shaw
Maintenance instructions for the Fujitsu ScanSnap S1300 Scanner. The manual outlines system configuration and operating guidelines, backup procedures, service procedures.
Manual for safe operation of the Zebex Z-8072 Barcode Reader. This guide elaborates on device features and installation procedures, setup, system parameters.
Comprehensive user handbook for the Leica ScanStation P Series Remote Control. It includes maintenance procedures and testing procedures, regulatory notices, operational guidelines.