Homestyles 451 -95 Quick Start Manual

M4x22 Machine Screw 8 pcs. Handle 4 pcs. M3x16 Wood Screw for Leaf Support 6 pcs. (+1 extra) M3x16 Wood Screw for Magnet 4 pcs. (+1 extra) M3x25 Wood Screw (long) 24 pcs. (+1 extra) M3x25 Flat Head Screw 3 pcs. (+1 extra) M3x16 Wood Screw (short) 2 pcs. (+1 extra) 0 Hex Wrench 1 pc. M6x12 Head Cap Bolt for Caster 16 pcs. (+1 extra) M6x25 Head Cap Bolt 4 pcs. (+1 extra) M6x38 Head Cap Bolt (long) 4 pcs. (+1 extra) Magnet 2 pcs. A. Top 1 pc. M. Rack Side 1 pc. N. Rack Side 1 pc. P. Rack Bar 1 pc. O. Rack Base 1 pc. W. Base 1 pc. Q. Shelf 4 pcs. R. Door 1 pc. S. Door 1 pc. U. Leaf Support 1 pc. T ...

IMPORTANT � Use a soft cloth between these parts and the floor. � Do not use power tools above 8 volts to assemble. � Do not tighten all the bolts until each part is properly assembled. � Keep Hex Wrench as the bolts may need to be tightened in the future. STEP 2 Attach unit to Side Panel (C) with Head Cap Bolts. Head Cap Bolt STEP 3 Attach Arms (K) to Side Panel (B) with Head Cap Bolts. Head Cap Bolt K C B K STEP 1 Assemble Rack Sides (M), (N), Rack Base (O) and Rack Bar (P). P O N M ...

Lock Figure 1 Figure 2 STEP 4 Attach Back Rail ( ) H to Side Panel (C), then flip Locks. (See Figures 1 and 2) Attach Back Uprights ( ) G to unit. Slide Back Panels ( ) F into position. Attach Back Rail ( )I to unit, then flip Lock. Attach Side Panel (B) to unit, then flip Locks. Figure 3 STEP 5 Attach Base ( W) to unit with Head Cap Bolts (long), then flip Locks. (See Figure 3) Note: Arrow label indicates front of Base ( ). W F C F G F H G B I Arrow label at front W Head Cap Bolt (long) Lock ...

STEP 7 Turn unit over to its upright position. Attach Middle Panel (D) to unit, then flip Locks. Attach Front Rail (J) and Middle Panel (E) to unit, then flip Lock. Insert Wood Screws (short) into pre-drilled holes in unit, then tighten. Slide Towel Bar (L) into position. Figure 4 STEP 6 Attach Casters to unit with Head Cap Bolts for Caster into pre-drilled holes with Locking Casters at front. (See Figure 4) Note: Arrow label indicates front of unit. Arrow label at front Head Cap Bolt for Caster Non-Locking Caster Locking Caster Wood Screw (short) Lock L E J D ...

Figure 5 STEP 8 Attach Leaf Supports (U) and (V) to unit with Wood Screws for Leaf Support. (See Figure ) 5 Wood Screw for Leaf Support U V Wood Screw for Magnet Magnet STEP 9 Attach Magnets to Front Rail ( ) X by inserting Wood Screws for Magnet into pre-drilled holes, then tighten. (See Figure ) 6 Figure 6 X ...

Insert Adjustable Pins into side panels and middle panels at desired level. (See Figure 7) Place Shelves (Q) into position. Attach Doors (R) and (S) by sliding door hinges into side panel hinges. (See Figure 8) Attach Handles to Doors (R) and (S) with Machine Screws. (See Figure 9) Assembly Instructions 6/8 Figure 7 Figure 8 Figure 9 Adjustable Pin S Q Q Q Q Handle Machine Screw R X ...

Handle Drawer (T) Wood Screw (short) Roller at back Bottom STEP 11 Attach Drawer Front (T1) and Drawer Back (T2) to Drawer Side (T3) with Wood Screws (long). Attach Drawer Side (T4) to unit with Wood Screws (long). Wood Screw (long) Machine Screw Handle STEP 12 Slide Drawer Bottom (T5) into groove. Attach Drawer Bottom (T5) to unit with Wood Screws (short). Assembly Instructions / 7 8 T1 T2 T5 T3 T4 ...

STEP 14 Attach Top (A) to unit with Flat Head Screws, then flip Locks. Slide Drawers (T) into position. T A T Lock Flat Head Screw ...

finished furniture. Ammonia chemically attacks the finish. allow liquids to remain on furniture. Absorption causes parts to warp and split and finishes to delaminate. NEVER CARE INSTRUCTIONS Do not use rubber based placemats. PREVENT DISCOLORING Do not use commercial waxes and polishes. PREVENT YELLOWING Do not place hot objects on surface. PREVENT FINISH DAMAGE Do not write directly on surface. PREVENT MARKING Do not use power tools above 8 volts to assemble. PREVENT CRACKING Do not place in direct sunlight. PREVENT FADING with a soft cloth moistened in lukewarm soap and water. Buff with a dry clean cloth. CLEAN homestyles ...