Jedia J6CD-10 Operating Instructions Manual
Text of the manual
IMPORTANT NOTICE (중요사항)
SAFETY INSTRUCTIONS
C
1
1
1
4~5
RONT PANEL CONTROLS
F
2
NSTALLATIONS
I
H OW TO USE THE COMPACT DISC MAGAZIN (콤팩트 디스크 매거진 사용방법)
3
F EATURES (특징)
4
E RROR DISPLAY (에러발생시 대응법)
7
B LOCK DIAGRAM
9
S PECIFICATIONS
8
R EAR PANEL CONTROLS
6
6
5
4
3
2
1
J6CD-10
6CD CHANGER
MAIN
Read all safety instruction before operating the J6CD-10.
1. Install equipment as follow conditions.
The apparatus shall not be exposed to dripping or splashing and
no object filled with liquids, such as vases, shall be place on the
apparatus.
Install at the place, not bending curved.
Do not install this apparatus in a confined space such
I NSTALLATION (설치)
CR2023
RELEASE
STORAGE DISC
Be sure to keep discs away from CD changer during long-time not use.
Be sure to keep in the case.
Do not place or store disc in the following place.
1. Locations exposed to direct sunlight.
2. Locations directly exposed to a heat vent or heating appliance.
3. Humid locations.
USE OF BATTERIES
디스크 보
Inserting discs into the suppled magazine.
Up to 6 discs may be inserted into the magazine.
The discs are numbered from 1(bottom tray) to 6(top tray).
※Note : Do not touch the recorded side of a disc while inserting or
removing it.
INSERTING DISC
1. CD 매거진에 표시된 측변 방향으로 디스크를 삽입하십시오.(fig.1)
2. a.
CAR STEREO AUTO 6CD CHANGER DECK MECHANISM USE
특 징
PLAY/PAUSE FUNCTION
STOP FUNCTION
EJECT FUNCTION
TRACK SELECT FUNCTION (T-UP, T-DN)
REPEAT(DISC) FUNCTION(RPT)
RANDOM(DISC) FUNCTION(RDM)
SCAN(DISC) FUNCTION(SCAN)
PICK-UP(SONY)
PERMISSABLE REMOTE-CONTROL
L,R STEREO OUTPUT AND MONO OUTPUT
AC, DC24V USE
REMOTE-CONTROLLER RECEIVER SENSOR
LED
7. REMOTE-CONTROLLER SENSOR RECEIVING LIGHT
This is to receive infrared signal form card-type remote controller.
(Avoid any foreign substances or contamination)
9. EJECT BUTTON (EJECT)
Press eject button for take out magazine from the CD mechanism.
10. REPEAT PLAY BUTTON (TRACK OR DISC REPEAT)
It is used for repeating the play. Pressing this button once,"R
1. AC POWER
1. AC INLET
6
Plug AC input cord into AC out inlet.
3. DC POWER TERMINAL
Please note the +,- polarity, when connecting DC 24V terminal in
case of using emergency power source for unexpected AC power
failure.
4. MONO OUTPUT BALANCED
Audio signal output connector for mono output 0dB/600ohm balanced.
5. STEREO L,R OUTPUT
Audio signal output connecto
E RROR DISPLAY (에러 발생시 대응책)
Error 3
LOADING is not completed after a certain time(8 sec) passed.
Error 2
It is impossible to discharge magazine while ejecting.
Error 1
There's no magazine, and DISC is clamping.
Error 5
ELEVATOR does not reach to the target position after a certain time(8sec) passed. Hole separated.
Error 6
PICKUP is not mov
MONO 0dB(0.775V) / BAL
L, R 0dB(0.775V) / UNBAL(OPTION)
Digital Filter
8-TIMES OVER SAMPLING
T.H.D(1KHz)
LESS THAN 0.03% (JIS A)
Signal to Noise Ratio(1KHz)
MORE THAN 85dB (JIS A)
Dynamic Range(1KHz)
MORE THAN 70dB
Channel Separation(1KHz)
MORE THAN 70dB (JIS A)
Frequency Response
20Hz~20KHz(
3dB )
Wow / Flutter
BELOW