Lanner NCS2-VT04 Operation & User’s Manual

2 This manual describes the overview of the various functionalities of this product, and the information you need to get it ready for operation. It is intended for those who are: - responsible for installing, administering and troubleshooting this system or Information Technology professionals. - assumed to be qualified in the servicing of computer equipment, such as professional system integrators, or service personnel and technician ...

3 Taiwan Corporate Headquarters Lanner Electronics Inc. 7F, No.173, Sec.2, Datong Rd. Xizhi District, New Taipei City 22184, Taiwan 立端科技股份有限公司 221 新北市汐止區 大同路二段 173 號 7 樓 T: +886-2-8692-6060 F: +886-2-8692-6101 E: [email protected] China Beijing L&S Lancom Platform Tech. Co., Ltd. Guodong LOFT 9 Layer No. 9 Huinan Road, Huilongguan Town, Changping District, Beijing 102208 China T: +86 0 ...

4 Follow these guidelines to ensure general safety: Keep the chassis area clear and dust-free during and after installation. Do not wear loose clothing or jewelry that could get caught in the chassis. Fasten your tie or scarf and roll up your sleeves. Wear safety glasses if you are working under any conditions that might be hazardous to your eyes. Do not perform any action that creates a potential hazard to people or makes the equ ...

6 Ordering Information ................................................................................................................... 7 Optional Accessories .................................................................................................................... 7 System Specifications ................................................................................................................... 7 Physical Overview ...

7 The NCS2-VT04’s support for 10bit HEVC encoding enables de-interlacing, image scaling, frame rate conversion and graphical acceleration for transcoding efficiency that makes available high quality and bandwidth-hungry video content. SKU No. Main Features NCS2-VT04A VT04A + sub NCS2-VT04A (i7-1185G7E Tiger Lake U CPU) NCS2-VT04D VT04D + sub NCS2-VT04A (Celeron 6305E Tiger Lake U CPU) Type Description Storage M.2 SATA 2422 Card Syst ...

8 No. Description F1 Reset Button 1x Reset Button F2 LED Power/LAN/Status refer to Appendix A No. Description A CPU CPU B Memory SO-DIMM C Power Board Power Board F1 F2 B A C ...

9 The block diagram indicates how data flows among components on the board. Please refer to the following figure for your motherboard’s layout design. ...

10 To reduce the risk of personal injury, electric shock, or damage to the system, please remove all power connections and wear ESD protection gloves when handling the installation steps. 1. Power off the system and select an NCS2 slot on the system. Note: The system shown in the image below is for reference only. 2. Rotate clockwise and loosen the two lock- screws on the door. 3. Remove the door and insert the module. Align the golde ...

11 4. Once the module is firmly seated, rotate counter-clockwise and tighten the two (2) lock-screws. The NIC module has been successfully installed. ...

12 Revealing the M.2 Socket 1. Unscrew the four (4) screws holding down the motherboard. 2. Turn the motherboard over and unscrew the four (4) screws securing the heatsink. 3. Turn the motherboard back around and carefully lift up the heatsink. Disconnect the connector cable from the connector pin. Installing the M.2 Module Card 4. Locate the M.2 slot on the motherboard ...

13 5. Align the notch of the M.2 memory card with the socket key in the pin slot. 6. Insert the M.2 memory card pins at 30 degrees into the socket until it is fully seated. 7. Push down on the module and secure it with a screw. 8. Carefully place the heatsink back on the motherboard. Connect the heat sink connector cable to the connector pin. 9. Turn the motherboard around, and line up the four (4) holes and re- secure the heatsink on ...

14 10. Turn the motherboard back around and secure the motherboard with four (4) screws. ...

15 BIOS (Basic Input / Output System) is the program that controls the computer boot process. NCS2-TV04 supports Intel® Media SDK and OpenVINOTM Toolkit, for additional information, please inquire Lanner Technical Support. BIOS is a firmware embedded on an exclusive chip on the system’s motherboard. The module has AMI BIOS built-in, with a setup utility that allows users to configure required settings or to activate certain system ...

16 Setup main page contains BIOS information and project version information. Feature Description BIOS Information BIOS Vendor: American Megatrends Core Version: AMI Kernel version, CRB code base, X64 Compliancy: UEFI version, PI version Project Version: BIOS release version Build Date and Time: MM/DD/YYYY Access Level: Administrator / User System Date To set the Date, use to switch between Date elements. Default Range of Year: ...

17 Select the Advanced menu item from the BIOS setup screen to enter the “Advanced” setup screen. Users can select any of the items in the left frame of the screen. ...

18 Feature Options Description Intel (VMX) Virtualization Technology Enabled Disabled When enabled, a VMM can utilize the additional hardware capabilities provided by Vanderpool Technology. Active Processor Cores All 1 2 3 Number of cores to enable in each processor package. Hyper-Threading Enabled Disabled Enable or Disable Hyper-Threading Technology. BIST Enabled Disabled Enable/Disable BIST (Built-In Self Test) on reset ...

19 This feature can be available upon customer request, Standard will hide these features. This feature specifications have not yet been determined by customer. ...

20 Feature Options Description ME State Enabled Disabled Configure Management Engine Technology Parameters ...