Graco SD Composite Series Instructions Manual

Text of Graco SD Composite Series Instructions Manual

SD Composite, SD

and XD Series Hose Reels 313431H ENG For dispensing air, water, antifreeze, windshield washer solvent, transmission fluid, oil and grease. For professional use only. Not for use in explosive atmospheres. A complete list of Models, including Maximum Working Pressure, begins on page 2 Important Safety Instructions Read all warnings and instructions in this manual. Save these instructions. (HS Models) (HP Models) ti13193 ti13192

SD Composite Series (Parts List, page 27)

*Each HR or HP Model hose reel shown in the tables below is available in several colors. The last character of each Model No. indicates the hose reel color. For example: A = white, B = metallic blue, C = red, D = black, E = Mercedes blue, or F = yellow. (Other color choices may be available from your Graco Distributor.) On the table below this last character is represented by the generic # s

XD Series (Parts List page 30)

**Each HS or HN Model hose reel shown in the table below is available in either white, metallic blue or yellow. The last character of each Model No. indicates the hose reel color. For example: A = white, B = metallic blue, F = yellow. (Other color choices may be available from your Graco Distributor.) On the table below this last character is repre- sented by the generic # symbol. For example to show the comp

The following warnings are for the setup, use, grounding, maintenance, and repair of this equipment. The exclama-

tion point symbol alerts you to a general warning and the hazard symbol refers to procedure-specific risk. Refer back to these warnings. Additional, product-specific warnings may be found throughout the body of this manual where applicable. WARNING FIRE AND EXPLOSION HAZARD When flammable fluids are present in the wo

MOVING PARTS HAZARD

Moving parts can pinch or amputate fingers and other body parts. • Keep clear of moving parts. • Do not operate equipment with protective guards or covers removed. • Pressurized equipment can start without warning. Before checking, moving, or servicing equipment, follow the Pressure Relief Procedure in this manual. Disconnect power or air supply. PRESSURIZED EQUIPMENT HAZARD Fluid from the gun/dispense valve, le

Overhead-Mounted Hose Reel

Key: A Main air supply line B Pump air supply line C Air filter D Air regulator E Bleed-type master air valve (required) F Pump G Pump grounding wire (required) H Fluid drain valve (required) J Fluid shutoff valve K Fluid line L Hose reel fluid inlet kit M Hose reel N Dispensing valve P Mounting channel/base A ground wire (G), bleed-type master air valve (E) and fluid drain valv

The typical installations shown in FIG. 1 is only a guide

for selecting and installing a hose reel system. The com- ponents shown are the minimum requirements for all systems. However, it is not an actual system design. Contact your Graco distributor for assistance in design- ing a system to suit your needs. NOTE: The air and fluid accessories required for your pump must be properly sized to that pump. Refer to your spec

Installation Mounting Options

Mounting Adapter Kit for Replacing Series 500 Reels A Mounting Adapter Kit is available for installing an XD Series Hose Reel in the same location that a Series 500 Hose Reel was previously installed. Order Graco Kit No. 24A224. See FIG. 2 and page 35. A = Original Series 500 holes in mounting surface. B = Holes on the bottom of adapter bracket, predrilled to match original Series 500 hole configuration

NOTE: Always use all 4 large flat washers with 4 bolts to

mount the hose reel pedestal to any surface. All Models Select the reel bank mounting location. • For high ceilings, suspend a suitable support structure for the reels, so the hoses will be long enough to reach your service area. • A reel bank mounted in a one-lift service bay should be at least 6-ft (1.9m) from the center line of the lift (FIG. 6). • In a one-lift bay,

Graco Tools Owners Instructions: