Comelit UT1020 Technical Manual

Art. UT1020 Simplebus1 Ultra remote camera audio module Art. UT1010VC TECHNICAL MANUAL

systems in residential, commercial, industrial and public buildings. Installation All activities connected to the installation of Comelit products must be carried out by qualified technical personnel, with careful observation of the indications provided in the Manuals / Instruction sheets supplied with those products. Wires Disconnect the power supply before carrying out any operations on the wiring. Use wires with a cross-section suited to the distances involved, observing the instructions provided in the system manual. We advise against running the system wires through the same duct as power cables (230V or higher). Safe usage To ensure Comelit products are used safely: • carefully observe the indications provided in the Manuals / Instruction sheets, • make sure the system created using Comelit products has not been tampered with / damaged. Service Comelit products do not require maintenance aside from routine cleaning, which should be carried out in accordance with the indications provided in the Manuals / Instruction sheets. Any repairs must be carried out: • for the products themselves, exclusively by Comelit Group S.p.A., • for the systems, by qualified technical personnel. Disclaimer Comelit Group S.p.A. does not assume any responsibility for • any purpose other than the intended use, • failure to observe the indications and warnings contained in this Manual / Instruction sheet. Comelit Group S.p.A. reserves the right to change the information provided in this Manual / Instruction Sheet at any time and without prior notice.

Warning............................................................................................. 2 Description........................................................................................ 4 UT1020.......................................................................................................4 UT1010VC..................................................................................................4 Installation notes (Art. UT1020)....................................................... 6 Technical specifications.................................................................. 7 Art. UT1020................................................................................................7 Art. UT1010VC...........................................................................................8 Installation......................................................................................... 9 Flush-mounted installation composition table.....................................9 Surface-mounted installation composition table.................................9 Flush-mounted installation............................................................ 10 Removing nameplates (2A) / module (2B).............................................11 Installation with side-by-side boxes......................................................12 Wall-mounted installation.............................................................. 13 Optional........................................................................................... 13 Removing nameplates (2A) / module (2B).............................................14 Installation with side-by-side boxes......................................................15 Connections.................................................................................... 16 Connections for UT1020, UT1010VC.....................................................16 Variants....................................................................................................16 Remote camera connection (Art. UT1010VC only)...............................17 Module connection......................................................................... 18 Connection of button modules Art. UT9200......................................18 Connection of Touchscreen module Art. UT9270..............................18 Connection of number keypad module Art. UT9279M......................19 Programming.................................................................................. 20 Configuring the button type to maintain during normal operation (single/dual).............................................................................................20 Address button modules........................................................................20 Program call addresses..........................................................................20 Smart programming of consecutive addresses.......................... 21 Programming of specific addresses............................................. 22 Special programming via DIP Switch........................................... 23 Special programming table....................................................................24 Twilight sensor................................................................................ 26 Camera LED lighting and button backlighting management..............26 Checking twilight sensor operation......................................................27 Adjusting the brightness of the button LEDs and the camera light...28 Light-me function........................................................................... 29 Light-me function behaviour on the basis of the LED backlighting mode........................................................................................................29 Replacing the audio/video module with programming restore backup............................................................................................. 30 Configuring via PC......................................................................... 31 Errors and indications.................................................................... 31 System performance and layouts................................................. 31 Addressing table............................................................................. 32

and art. 4888C. Wide-angle colour video camera (field of vision: 120° horizontal, 90° vertical) UT1010VC Audio module designed for connection of an analogue remote camera with PAL standard for Ultra entrance panel, Simplebus1 system. To be used in systems with power supply unit art. 1595 and art. 4888C. Easy to install and simple to configure, thanks to the smart programming of call buttons. Twilight sensor for automatic nameplate backlighting switch-off during daylight hours. Omnidirectional digital microphone and double loudspeaker for high-fidelity audio. Audio-visual indications for disabled individuals assistance request can be activated via programming. Facility for 2 call buttons. To be finished with cap, single button or dual button made using aluminium or professional grade plastic treated to prevent yellowing and dulling. Adjustment and programming can take place without removing the module. Dimensions: 100 x 90 x 35 mm. ULTRA: the new and most technologically advanced entrance panel offering maximum ease of installation. Available in flush-mounted (10 mm protrusion from the wall) or surface-mounted (just 35 mm protrusion from the wall) variants.

7. 9. 10. 11. 12. 8. 1. 2. 2. 16. 17.   1. Indicator LEDs call sent (green) / system busy (red) lock-release enabled communication enabled   2. Loudspeakers   3. Colour video camera (with Art. UT1020 only)   4. Speaker volume control   5. S1 Button programming selector   6. S2 Special programming selector   7. Micro USB input for programming via computer   8. Twilight sensor   9. Addressing and programming Dip Switches 10. Microphone volume control 11. Programming confirmation button 12. Digital microphone Use screwdriver supplied 13. Terminal block for connection: RTE programmable RTE (local lock-release input) or DO input (door open indication) GND RTE or DO input reference negative IF door lock reference negative NO NC COM relay contacts V- V+ power supply LL bus line connection 14. Ethernet terminal block, only for use in case of additional modules with LAN 15. Connector for additional modules with LAN 16. 17. Connector for additional module connection 18. Remote camera connection (with Art. UT1010VC only): in flush-mounted installations, use the terminal; in surface-mounted installations, solder the wires and use the heat-shrink sheath.