EK-Quantum Vector Strix RTX 3070 Backplate Operation & User’s Manual

Carefully read the manual before beginning with the installation process. Remove your graphics card from the computer for the safest mounting process to prevent any possible damage to your GPU or its circuit board (PCB). EK Fittings require only a small amount of force to screw them f ...

TABLE OF CONTENTS BOX CONTENTS 4 WATER BLOCK DIMENSIONS 5 TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS 6 PREPARING THE GRAPHICS CARD  7 REMOVING THE STOCK COOLER  7 CLEANING THE PCB  7 CUTTING AND PLACING THERMAL PADS 8 APPLYING THERMAL COMPOUND 9 INSTALLING THE WATER BLOCK 9 PLACING THE BLOCK ON THE GRAPHICS CARD 9 ATTACHING THE BLOCK TO T ...

BOX CONTENTS 4 mm 4 mm 6 mm 8 mm M3x4 DIN7985 Screw (2 pcs) EK-Loop Multi Allen Key (1 pc) M2.5 Nut (6 pcs) M2.5x6 AX1 Screw (13 pcs) Allen Key 2.5 mm (1 pc) Thermal Pad F 1.0 mm (3 pcs) Thermal Grease (1 pc) M2.5x8 AX1 Screw (2 pcs) M2.5x4 AX1 Screw (16 pcs) EK-Quantum Vector TUF RTX 3070 D-RGB PVC Washer M2.5 (16 pcs) 120 mm 16 mm EK-Plug G1/4 (2 ...

TECHNICAL SPECIFICATIONS AND WATER BLOCK PARTS Technical Specification: - Dimensions (L x H x W): 254.5 x 149 x 20.5 mm - D-RGB cable length: 500 mm - D-RGB LED count: 9 - D-RGB connector standard 3-pin (+5V, Data, Blocked, Ground) Position EAN Description Quantity 1 101743 Terminal cover + D-RGB LED 1 2 8311 M4 x 20 DIN7984 Screw 3 3 101628 FC Termina ...

PREPARING THE GRAPHICS CARD STEP 1 REMOVING THE STOCK COOLER Place your graphics card on the flat surface and carefully remove the stock cooler. Do not forget to unplug all the LED and fan connectors. Pay attention to the following steps when installing EK-Quantum Vector TUF RTX 3070 water block onto your graphics card. STEP 2 CLEANING THE PCB Wipe off ...

STEP 1 Your GPU water block comes with thermal pads that have to be cut into smaller pieces to cover all the VRM components, such as COILs, MOSFETs, and drivers. You must remove the protective foil from both sides of the thermal pad before installation. Replacement thermal pads: 3x Thermal Pad F 1.0 mm – (120 x 16 mm) EAN: 3830046996732 STEP 1 Therma ...

Thermal Grease STEP 1 Apply the enclosed EK-TIM Ectotherm thermal grease (thermal compound) on the GPU heat spreader – IHS – as shown in the image. The layer of the thermal compound must be thin and even over the entire surface of the IHS. The excessive or uneven application of thermal grease may lead to poor performance! STEP 1 APPLYING THERMAL CO ...

For this Step, you will need: M 2.5 PVC Washer (14 pcs) M2.5 x 4 AX1 Screw (14 pcs) Phillips Head Screwdriver 4 mm STEP 2 M2.5 x 4 AX1 SCREW M2.5 PVC WASHER STEP 2 ATTACHING THE BLOCK TO THE GRAPHICS CARD Use fourteen (14) M2.5 x 4 AX1 Screws and fourteen (14) M2.5 PVC Washers. Tighten the screws evenly using the Phillips head screwdriver. EK recommen ...