CATSKILL 54230 Assembly Instructions Manual

Text of CATSKILL 54230 Assembly Instructions Manual

Butcher Block WorkCenter PLUS

GENERAL: 1. You have purchased model 54230. 2. Should you need assistance or need to replace a damaged or missing part simply give us a call M-F at 607-652-7321 from 7:30 am - 4:30 pm EST and we’ll send you the prepaid part via UPS usually that same day! You may also email us [email protected]. 3. Read the assembly instructions and the enclosed brochure before beginning assembly. As

Parts List Model 54230

Drawer Bottom (1) P/N DBOT-54230 Small Middle Shelf (2) P/N SMS-54230 Center Shelf (1) P/N CS-54230 Bottom Shelf (1) P/N BS-54230 Left Center Door (1) P/N DOR-54230LC Left Door (1) P/N DOR-54230LO Right Door (1) P/N DOR-54230RO Right Center Door (1) P/N DOR-54230RC Table Top (1) P/N TT-54230 Side Panel (2) P/N SP/HDL-54230 Divider Panel (2) P/N DP-54230 Back Panel (1) P/N BP-54230 Glide Support Stick (2) P/N GLDSUP-54230 Drawer Front

Hardware for 54230

1 3/4” Phillips Flat Head Bolt (8) 1 1/4” Phillips Flat Head #8 Screw (20) 7/8” Truss Head Machine Screw (8) 5/8” Pan Head Screw (8) 3/4” Long 3/16” DIA. Steel Pin (4) 1” Long 3/16” DIA. Steel Pin (22) 1 1/2” Long 3/16” DIA. Steel Pin (8) Caster Socket (4) 5/8 Wooden Disk (8) Nickel Handle (6) Towel Bar Post (2) Wheel Casters (2) Locking Wheel Casters (2) Magnet Plate (4) Magnet (4) 3/16” Flat Washer (8) 10-24 Hex N

A. Tap/insert ONE 1 1/2” pin into each end of all the doors. DON’T OVERDRIVE PINS! Pins should

stick up about 1/2” when seated. STEP 2 Take the 2 front braces and tap/insert one 3/4” steel pin into each end of both braces until seated. About 3/8” will stick out when seated. Ok if loose. 4 used in this step 3/4” Long 3/16” DIA. Steel Pin STEP 3 Assembly Spice Rack Insert retainer rods into holes Fasten Shelves with 1 1/4” Phillips Fla

A. Attach the Drawer Back to the Drawer Sides with four 1 1/4” #8 screws. There are left and right

sides. Make sure the slots that run the length of the Sides are aligned with the slot in the Drawer Back to accept the Drawer Bottom. B. Slide in Drawer Bottom, best side up, to inside of drawer. C. Take the 2 bastion posts, align the threaded end of the posts with the post holes located near the ends of the inside of the Drawer Front. Tighten posts

Post needs to be screwed deeper.

WRONG! Post needs to be backed out. CORRECT! Set screw secures post properly. Step 1 1. The Bastion fastening system consists of a steel post (threaded on one end with a hole through the shaft on the other end); a Barrel Nut (cylindrical barrel-shaped with threaded open end & holes through the sides); and a Set Screw (Phillips slot on one end, pointed on the other) 2. To attach Posts: A) Dip threads of Post in vegeta

A. Attach a Glide Support Stick to the top of each Side Panel using 1 1/4” #8 screws. The

countersunk holes (reamed out) in the stick are positioned as in illustration so that the glide holes are toward the lower edge. Sticks should be lush with top of panel. B. Attach the cabinet glide of the Drawer Glides to the Glide Support Stick using 5/8” #7 lat head screws. Left glide to left Side Panel, right glide to right Side Panel. The glides look a

CATSKILL Indoor Furnishing Owners Instructions: